Program Bank 3 Entry Mode Page 20 Program Bank 3 Feature Selections Page 21 Wiring Diagram Page 22 Notes Page 23 and 24 PATENTED: www.voxxintl.com/company/patents 128-8791b PRO9056C New Format Add Timing PASD & Light Blue + DBI Lock, Lock, Lock 5/2013 1 of 24...
Before You Begin PROFESSIONAL INSTALLATION IS STRONGLY RECOMMENDED Roll down window to avoid locking the keys in the vehicle during installation. Avoid mounting components or routing wires near hot surfaces or near moving parts like the steering wheel as it may prevent proper operation of the vehicle.
Page 3
12 Pin Main Wiring Harness #1123751 Yellow/Black (+) Output To Control Factory Alarm Green/Orange Tachometer Input Black Chassis Ground Gray/Black Negative Inhibit Shutdown Input (-) Light Blue Ground Output While Running (-) 300mA Green/Yellow Diesel Wait To Start Input Gray Shutdown Input (-) No Connection Brown...
Page 4
2 Pin Transponder Output Harness #1123292 Battery (+) 100mA Black (-) Output While Running 100mA 5 Pin Antenna Harness Part # 1123906 128-8791b 4 of 24...
This Remote Start/Alarm System is designed to be used with Automatic Transmission- Fuel Injection Gas or Diesel Vehicles Only! INSTALLATION OF THE MAJOR COMPONENTS: CONTROL MODULE: PART # 1365038 Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting location selected must be within 24"...
Page 6
3 Fused RED WIRE: + 12 Volt Battery 2 Source Locate the vehicle battery wire (s) at the ignition switch. Verification: These wires will register voltage in all positions of the ignition switch. Connect the Red wire to the vehicle's battery wire. This wire provides power for the start relay and the accessory relay.
Page 7
WIRING CONNECTIONS: 12 Pin Accessory Input/Output Harness PART # 1123751 1 Yellow/Black Wire: + 12 Volt Alarm By - Pass Output NOTE: You must disconnect the ignition input of the alarm from any other wire that it is presently connected to in the vehicle.
Page 8
B. Ignition 3 Output: Some newer vehicles use a third ignition wire, which is required to start and keep the vehicle's engine running. If this is the case, connect the Light Blue wire to terminal #86 of an external relay. Connect terminal #30 & #85 to a fused + 12 volt battery source rated for a minimum of 25 Amp.
Page 9
8 Brown Wire: Positive Inhibit Input 1 Any time + 12 Volts is applied to the Brown wire, the Remote Starter will stop operating, even if the signal is received from the transmitter. If the vehicle has a factory installed hood pin switch and that switch provides + 12 Volts to an under hood light, the Brown wire can be connected to the existing pin switch.
Page 10
WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS Part #1122585 The auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during different stages of the Remote Start unit's operation. Understanding these outputs and the time in which they occur will allow you to determine if they are needed for the particular vehicle you are working on as well as how to use them.
2 Pin Transponder Control Output: (Yellow Connector) Part # 1122392 a: When selected for while remote start on, the black wire will be active at the same time ign. 3 becomes active, and will remain active all the time the unit is operational under the control of the remote start. b: When selected for output during the start sequence, the black wire will be active at the same time Ign.
3. Connect the Yellow wire to a +12 volt ignition 1 source. This wire will have +12 volts with the ignition in the on and start position and have 0 volts with the ignition in the off position. 4. Connect the Green wire to the (Green) or (Orange/Green) tach input of the Audiovox remote start unit. 128-8791b...
TESTING YOUR INSTALLATION: WARNING!! The following procedure must be performed after the installation of any Remote Start Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury, property damage, or both. HOOD PIN SAFETY SHUT DOWN: The intent of the hood pin safety shut down is to prevent the Remote Start unit from being activated while a mechanic or vehicle owner is performing normal routine vehicle maintenance.
To Exit Remote Start Override Mode: 1) With the system disarmed, Press and Hold the PBLED on. 2) Turn the ignition switch on, off, on, off, on, off. 3) The LED turns off indicating that the R/S unit is fully functional one again. DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE OPERATION OF THE MANUAL SHUT DOWN / ENABLE FEATURE.
Mechanical Neutral Start Switch from starting in gear. AUDIOVOX ADVISES THAT YOU MAINTAIN THE FACTORY CIRCUIT WHENEVER POSSIBLE. The following two circuits may be used only if the above circuit is not available.
Page 16
5) Connect the cathode (striped) side of a 4002 series diode to this same wire, and connect the (non striped) side to the negative shut down safety wire (Gray / Black) of the Audiovox Remote Start Unit. 6) Connect terminal 86 of the relay to a fused +12 volt constant battery source.
To connect to the key in sensor circuit as shown for method 2: 1) Locate the control wire that connects the drivers door pin switch to the key in sensor switch. 2) Cut this wire and connect the ignition cylinder side to chassis ground. 3) Locate the key in sensor switch wire that connects the chime module to the ignition cylinder .
The transmitters are pre-programmed from the factory, If you find you need to program new or additional transmitters follow the instructions below. PROGRAMMING BANK 1 (TRANSMITTERS): 1) Turn the ignition key to the on position. 2) Press and release the valet/programming switch 3 times. (Siren Chirps) 3) Press the Button of each transmitter you want programmed until you hear the parking light relay click.
Page 20
PROGRAMMING BANK 3 (REMOTE START ): You can enter Bank 3 from Bank 2 by turning the ignition key off then on after you've made the changes you wanted in Bank 2, (Siren two Long Chirp), You can also go right to bank 3 by: 1) Turn the ignition key to the on position.