Table of Contents
Advertisement
Table Of Contents:
PRO9056TW New Format Add Timing PASD & Light Blue + DBI Lock, Lock, Lock 5/2013
PATENTED: www.voxxintl.com/company/patents
Model PRO9056TW
Installation Manual
Vehicle Remote Start System
Page 2
Page 3 & 4
Page 5
Page 5 & 6
Page 7 - 9
Page 10
Page 10
Page 11
Page 11
Page 12
Page 12
Page 13
Page 13
Page 13
Page 14
Page 15
Page 15 - 17
Page 18
Page 19
Page 18
Page 20
Page 21
Page 22
Page 22
Page 23
Page 24
1
128-8857b
1 of 24
Advertisement
Table of Contents
Related Manuals for Audiovox PurSuit PRO9056TW
Summary of Contents for Audiovox PurSuit PRO9056TW
-
Page 1: Table Of Contents
Programming Bank 3 (Remote Start) Page 22 Tach Rate Programming Page 22 RF Programmable Features Bank 3 Page 23 Wiring Diagram Page 24 PATENTED: www.voxxintl.com/company/patents 128-8857b PRO9056TW New Format Add Timing PASD & Light Blue + DBI Lock, Lock, Lock 5/2013 1 of 24... -
Page 2: Before You Begin
Before You Begin PROFESSIONAL INSTALLATION IS STRONGLY RECOMMENDED Roll down window to avoid locking the keys in the vehicle during installation. Avoid mounting components or routing wires near hot surfaces or near moving parts like the steering wheel as it may prevent proper operation of the vehicle. -
Page 3: Wire Harnesses Quick View
12 Pin Main Wiring Harness #1123751 Yellow/Black (+) Output To Control Factory Alarm Green/Orange Tachometer Input Black Chassis Ground Gray/Black Negative Inhibit Shutdown Input (-) Light Blue Ground Output While Running (-) 300mA Green/Yellow Diesel Wait To Start Input Grey Shutdown Input (-) No Connection Brown... - Page 4 2 Pin Transponder Output Harness Part #1123292 Battery (+) 100mA Black (-) Output While Running 100mA 6 Pin Antenna Harness Part # 1123908 128-8857b 4 of 24...
-
Page 5: Installation Of The Major Components
This Remote Start/Alarm System is designed to be used with Automatic Transmission - Fuel Injection Gas or Diesel Vehicles Only! INSTALLATION OF THE MAJOR COMPONENTS: CONTROL MODULE: PART # 1365036 Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting location selected must be within 24"... - Page 6 3 Fused RED WIRE: + 12 Volt Battery 2 Source Locate the vehicle battery wire(s) at the ignition switch. Verification: These wires will register voltage in all positions of the ignition switch. Connect the Red wire to the vehicle's battery wire. This wire provides power for the start relay and the accessory relay.
-
Page 7: Wiring Connections: 12 Pin Accessory Input/Output Harness
WIRING CONNECTIONS: 12 Pin Accessory Input/Output Harness PART # 1123751 1 Yellow/Black Wire: + 12 Volt Alarm By - Pass Output NOTE: You must disconnect the ignition input of the alarm from any other wire that is presently connected to the vehicle. This wire provides a + 12 Volt output when the ignition key is turned to the “ON”... - Page 8 B. Ignition 3 Output: Some newer vehicles use a third ignition wire, which is required to start and keep the vehicle's engine running. If this is the case, connect the Light Blue wire to terminal #86 of an external relay. Connect terminal #30 &...
- Page 9 8 Brown Wire: Positive Inhibit Input 1 Any time + 12 Volts is applied to the Brown wire, the Remote Starter will stop operating, even if the signal is received from the transmitter. If the vehicle has a factory installed hood pin switch and that switch provides + 12 Volts to an under hood light, the Brown wire can be connected to the existing pin switch.
-
Page 10: Wiring The 4 Pin Auxiliary Output Harness
WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS Part #1122585 The auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during different stages of the Remote Start unit's operation. Understanding these outputs and the time in which they occur will allow you to determine if they are needed for the particular vehicle you are working on as well as how to use them. -
Page 11: Pin Transponder Control Output
2 Pin Transponder Control Output: (Yellow Connector) Part # 1123292 a: When selected for while remote start on, the Black wire will be active at the same time ign. 3 becomes active, and will remain active all the time the unit is operational under the control of the remote start. -
Page 12: Diagnostics
3. Connect the Yellow wire to a +12 Volt ignition 1 source. This wire will have +12 Volts with the ignition in the on and start position and have 0 Volts with the ignition in the off position. 4. Connect the Green wire to the (Green) or (Orange/Green) tach input of the Audiovox remote start unit. 128-8857b... -
Page 13: Testing Your Installation
TESTING YOUR INSTALLATION: WARNING!! The following procedure must be performed after the installation of any Remote Start Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury, property damage, or both. HOOD PIN SAFETY SHUT DOWN: The intent of the hood pin safety shut down is to prevent the Remote Start unit from being activated while a mechanic or vehicle owner is performing normal routine vehicle maintenance. -
Page 14: Neutral Start Safety Test
To Exit Remote Start Override Mode: 1. With the system disarmed, Press and Hold the PBLED on. 2. Turn the ignition switch on, off, on, off, on, off. 3. The LED turns off indicating that the R/S unit is fully functional one again. DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE OPERATION OF THE MANUAL SHUT DOWN / ENABLE FEATURE. -
Page 15: Mechanical Neutral Safety Switch Considerations
Mechanical Neutral Start Switch from starting in gear. AUDIOVOX ADVISES THAT YOU MAINTAIN THE FACTORY CIRCUIT WHENEVER POSSIBLE. The following two circuits may be used only if the above circuit is not available. - Page 16 5. Connect the cathode (striped) side of a 4002 series diode to this same wire, and connect the (non striped) side to the negative shut down safety wire (Gray / Black) of the Audiovox Remote Start Unit. 6. Connect terminal 86 of the relay to a fused +12 volt constant battery source.
- Page 17 METHOD 2: To connect to the key in sensor circuit as shown for method 2: 1. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. 2. Cut this wire and connect the ignition cylinder side to chassis ground. 3.
-
Page 18: Completing The Installation
COMPLETING THE INSTALLATION 1. Mount the control module up and behind the dash securing it in place with cable ties or screws. Be certain that the chosen mounting location will not inhibit any of the controls of the vehicle. 2. Securely harness and tie all wiring up and away from all hot and moving parts that they may come in contact with under the dash board or in the engine compartment areas. -
Page 19: Installation Notes
INSTALLATION NOTES 128-8857b 19 of 24... -
Page 20: Programming Bank 1 (Transmitters)
The transmitters are pre-programmed from the factory, If you find you need to program new or additional transmitters follow the instructions below. PROGRAMMING BANK 1 (TRANSMITTERS): 1. Turn the ignition key to the on position. 2. Press and release the valet/programming switch 3 times (Siren Chirps). 3. -
Page 21: Selectable Features
128-8857b 21 of 24... -
Page 22: Programming Bank 3 (Remote Start)
PROGRAMMING BANK 3 (REMOTE START ): You can enter Bank 3 from Bank 2 by turning the ignition key off then on after you've made the changes you wanted in Bank 2, (Siren two Long Chirp), You can also go right to bank 3 by: 1. - Page 23 128-8857b 23 of 24...
-
Page 24: Wiring Diagram
For technical support go to www.pursuitcarsecurity.com or call 1 800 225 6074 © 2013 Audiovox Electronics Corp., Hauppauge, NY 11788 128-8857b 128-8857b 24 of 24...