Advertisement
6) Keystone commands
The keystone commands are used for the keystone setting of this projector with the value. The value will vary
depending on the installation conditions, etc.)
ITEM
KEYSTONE(vertical)
KEYSTONE(horizontal) KSH
How to set the grade
Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code.
ASCII
'+'
'–'
HEX
2Bh
2Dh
7) Mute commands
screen is being displayed, the splash screen is not muted but only canceled.)
The mute commands are used for the mute setting of this projector with the 0(30h) and 1(31h).
ITEM
MUTE
8) Remote commands
splash screen is being displayed, the splash screen is only canceled.)
Some remote control operations can be achieved by the remote command codes. The remote commands have no data codes.
Button's name on remote
+ VOLUME
– VOLUME
KEYSTONE
EXPAND
PinP
MUTE
{
}
$
%
MENU
ENTER
AUTO POSITION
STILL
[Example] When displaying the MENU selection bar (Figures and symbols enclosed in quotation marks are
ASCII codes.):
Sending commands
from the PC, etc.
30 30 72 35 34 0D
'0' '0' 'r' '5' '4' '
'
9) Password lock commands
The password lock commands control the password lock. The password lock enabling or disabling command is
sent with a 4-digit figure (password) added to the end of the data code. When the password lock is enabled or
disabled successfully, the projector sends a return command comprising the data code, password, and "1" at
the end. When enabling or disabling the password lock fails, it sends a return command with "0" at the end.
There is no reconfirmation of the password. The password input command is for enabling projection of image
when password lock has been set to DISPLAY INPUT. The password input command is sent with a 4-digit
figure (password) at the end.
ITEM
ASCII
Password lock
PSLOCK
enabling/ disabling
Password input
PASS
is a 4-digit figure (password).
****
(Not executable in stand-by mode. Possible only to read during muting.)
ASCII
HEX
KS
4Bh
53h
4Bh
53h
'0'
'1'
'2'
'3'
30h
31h
32h
33h
(Not executable in stand-by mode. When the mute commands are sent while the splash
ASCII
HEX
MUTE
4Dh
55h
(Not executable in stand-by mode. When the remote commands are sent while the
ASCII
HEX
r06
72h
30h
r07
72h
30h
r43
72h
34h
r02
72h
30h
r04
72h
30h
ra6
72h
61h
r53
72h
35h
r2b
72h
32h
r4f
72h
34h
r59
72h
35h
r54
72h
35h
r10
72h
31h
r09
72h
30h
ra4
72h
61h
Status code from
the projector
30 30 72 35 34 0D
'0' '0' 'r' '5' '4' '
HEX
50h
53h
4Ch
50h
41h
53h
VALUE
±
45
±
48h
45
'4'
'5'
'6'
'7'
34h
35h
36h
37h
VALUE
0 (OFF), 1 (ON)
54h
45h
36h
37h
33h
32h
(For XL8U only)
34h
36h
33h
62h
66h
39h
34h
30h
39h
34h
'
VALUE
4Fh
43h
4Bh
0****(Disabling), 1****(DISPLAY INPUT)
2****(MENU ACCESS),
3****(SPLASH ID SCREEN)
53h
****
3
(For XL8U only)
'8'
'9'
38h
39h
Description
Command operating the same
as the MENU button
Command receipt confirmation
(Command echo back)
Advertisement
