Peg-Perego POLARIS SPORTSMAN 400 Use And Care Manual page 6

b = blue
bk = black
r = red
w = white
b = azul
bk = negro
r = rojo
w = blanco
b = bleu
bk = noir
r = rouge
w = blanc
ENGLISH
•PEG PEREGO® thanks you for choosing this product. For over 50 years, PEG
PEREGO has been taking children for an outing: first with its famous baby
carriages and strollers, later with its pedal and battery operated toy vehicles.
•Read this instruction manual carefully to learn the use of the vehicle and to teach
your child safe and enjoyable driving. Please keep this manual for use as a
reference in the future.
•Our toys conform with the safety requirements provided by the Council of the
EEC, of the T.Ü.V.; of the I.I.S.G. Istituto Italiano Sicurezza Giocattoli, and the U.S.
Consumer Toy Safety Specification F963.
•Peg Perego reserves the right to modify or change its product. Price, literature,
manufacturing processes or locations or any combination of the above
mentioned entities may change at any time for any reason without notice with
impunity.
Years 2-4
CAUTION:
ELECTRIC VEHICLE NOT RECOMMENDED FOR CHILDREN
UNDER 2 YEARS OF AGE. AS WITH ALL ELECTRIC
PRODUCTS, PRECAUTIONS SHOULD BE OBSERVED
DURING HANDLING AND USE TO PREVENT ELECTRIC
SHOCK. RECHARGER INCLUDED.120 VOLTS, 60Hz, 15W
INPUT, 6 VOLTS (DC) OUTPUT.
CUSTOMER SERVICE
PEG PEREGO offers after-sales services, directly or through a network of
authorized service centers for repairs or replacement parts. See the back cover of
this instruction manual for contact information.
ASSEMBLY INSTRUCTIONS
CAUTION:
ADULT ASSEMBLY REQUIRED.
USE CARE WHEN UNPACKING AS COMPONENTS TO BE
ASSEMBLED MAY POSE A SMALL PARTS/SHARP EDGE
HAZARD.
BATTERY ALREADY INSTALLED IN VEHICLE.
ASSEMBLY
1 • Check the forecarriage to be sure it is correctly fastened at points (A). Remove
the protective caps (B).
2 • Insert an iron washer on the pin of the forecarriage, as shown in the figure.
3 • (1)Insert one of the two front wheels: make sure you use the wheel shown in
Figure A. (2)Insert an iron washer.
4 • Insert a self-locking washer on the provided tool (shown in the figure).
Caution: The tabs of the self-locking washer must face the inside of the tool
(see small picture A). NOTE: the bag contains 8 self-locking washers. Keep 4 of
MEIE0036
5 • Fasten the wheel as shown in the figure, pushing the self-locking washer
6 • Snap on the stud cover. Perform the same operations as the ones in Figure 2
7 • Insert a self-locking washer on the provided tool (shown in the figure).
8 • Remove the grey protective caps at the ends of the rear axle. Insert the axle on
9 • (1)Insert an iron washer on the axle. (2)Insert the axle into one of the two rear
10 • Insert the axle with the wheel into the hole of the gearmotor, pressing to be
11 • Turn the wheel slightly to match up the gearmotor pentagon with the one on
12 • Insert the bushing as shown in the figure, working from the other side of the
13 • Insert an iron washer as shown in the figure.
14 • Reposition the tool (used previously to insert the self-locking washer - see
15 • (1)Position the remaining wheel end insert an iron washer. (2)Insert a self-
16 • Snap on the remaining stud covers on both sides.
17 • Position the handle support.
18 • Slide on the handle, orienting it as shown in the figure.
19 • Fasten the handle with a washer and screw.
20 • Position the cap by inserting the tongue (1) into the rear notch of the support.
21 • Apply the silver decal.
22 • Apply the glass on the front light till it clicks.
23 • Snap the front luggage rack onto the bumper.
24 • Hook the bumper to the vehicle, inserting the hooks into the specific holes on
25 • Fasten the front luggage rack using the two supplied screws.
26 • Position and fasten the rear luggage rack using the four supplied screws.
27 • Rotate the red catch behind the saddle until bringing it to the position shown
28 • Connect the two plugs.
29 • Reposition the saddle by sliding the two pins into the holes on the tank. Turn
VEHICLE FEATURES AND INSTRUCTIONS FOR USE
30 • GEARSHIFT LEVER: Your child will have fun pretending to change gears using
31 • ACCELERATOR/ELECTRIC BRAKE PEDAL: The vehicle brakes automatically
REPLACING THE BATTERY
32 • Rotate the red catch behind the saddle until bringing it to the position shown
33 • Lower the catch (1) and, at the same time, push the battery fastener as
34 • Replace the battery. (NOTE:The replacement battery – separately available – is
them apart as spare washers.
down completely.
for the other front wheel.
Caution: The tabs of the self-locking washer must face the inside of the tool
(see small picture A).
the tool as shown in the figure.
wheels: make sure you use the wheel shown in Figure A.
sure it exits from the opposite side of the vehicle.
the wheel (Figure shows incorrect fastening of the wheel).
shaft until it is hooked to the body.
Figure 7) on the axle from the wheel side. Place the vehicle on one side,
keeping the wheel underneath. Make sure the tool cannot shift.
locking washer on the provided tool (shown in the figure). Caution: The tabs
of the self-locking washer must face the inside of the tool (see small picture
A). (3)Fasten the wheel as shown in the figure, pushing the self-locking washer
down completely.
Turn the cap (2).
the body (1). Turn the entire assembly as indicated by the arrow (2).
on figure. A: the saddle is locked. B: the saddle can be lifted. Lift up the saddle.
the red catch behind the saddle in order to fasten it. The vehicle is ready to
use.
this gearshift lever, which can be rotated into two positions.
when your child lift his/her foot off the pedal.
on figure 26 (figure B). Lift up the saddle. Unplug the terminals. Unscrew the
battery fastener.
indicated by the arrow (2) to release it. Remove the battery fastener.
a 6v/ 7Ah battery pack without fuse). Replace and screw back on the battery
fastener. Connect the two plugs. CAUTION: When you have finished,
remember to close and fix down the seat.