Related Manuals for Q-See QSTC201
Summary of Contents for Q-See QSTC201
-
Page 1: Quick Start Guide
Remote Internet Monitoring Quick Start Guide For IP Camera Models: QSTC201 QSTC211... -
Page 3: Connection Diagram
*Note the IP Address for this example is 192.168.0.105, the Subnet Mask is 255.255.255.0 and the Default Gateway is 192.168.0.1 b. Insert the installation CD for the Q-See IP Camera and Install the Q-See IP Camera as prompted by the pop-up menu that appears on your screen. - Page 4 Q-SEE IP CAMERA MODEL QSTC201/211 QUICK INSTALLATION GUIDE With New Firmware v 1.3.0 Build 20091022 (Figure 2) *Note that the example of this IPTOOL screen above lists an IP Camera with the Device Name of “name”, an IP Address of 192.168.1.201, a Subnet Mask of 255.255.255.0 and a Gateway of 192.168.1.1 d.
- Page 5 Log on as directed in Figure 5 and you will see a video feed from your Q-See IP Camera as illustrated in Figure 6. Click the [Setup] button on the top of your toolbar (Number 11, Figure 6) and a configuration menu will appear on the left of your screen (see Figure 7).
- Page 6 Router’s manual for more accurate and detailed information. h. Run the IPTOOL program again to ensure that your new Q-See IP Camera is detected by your Router. If not, station your camera closer to your Router.
- Page 7 (as illustrated in Figure 3). This will generate a prompt for your User Name and Password (see Figure 5). Enter your information accordingly and you will see a live feed from your Q-See IP Camera in your IE Browser. Click on the Setup button on the toolbar within your Q-See IP Camera Live Feed screen (Figure...
- Page 8 Q-SEE IP CAMERA MODEL QSTC201/211 QUICK INSTALLATION GUIDE With New Firmware v 1.3.0 Build 20091022 (Figure 9) b. After you click the Setup button, a menu will appear on the left hand side of your screen (Figure 9). Click on the [Mail Config] option from the menu (circled in red, Figure 9). This will generate a configuration...
- Page 9 After you have completed the email setup process outlined above, you will now need to enable the Motion Alarm (alert) function for your Q-See IP Camera. From the menu on the left hand side of your setup screen (Figure 11), choose the [Motion Alarm] option. This will generate a “Motion Alarm Setting”...
- Page 10 Q-SEE IP CAMERA MODEL QSTC201/211 QUICK INSTALLATION GUIDE With New Firmware v 1.3.0 Build 20091022 (Figure 12) (Figure 13) 8 | P a g e...
- Page 11 Protocol Suite to notify a DDNS host to change the active DNS configuration of its hostnames or addresses. This is a useful feature that your Q-See IP Camera is equipped with and can be helpful in avoiding any issues that might occur due to frequent or unplanned changes to your Public/WAN IP address. Enabling DDNS on your Q-See IP camera will allow you to connect to your device through a DDNS host such as myq-see.com.
- Page 12 Click on the [Save] button at the bottom of your screen (Figure 16). j. Once you have completed the registration process and configured you DDNS settings, you can log in to your Q-See IP Camera from anywhere by entering your domain address in the address bar of your IE Browser.
- Page 13 Q-SEE IP CAMERA MODEL QSTC201/211 QUICK INSTALLATION GUIDE With New Firmware v 1.3.0 Build 20091022 Questions or Comments? Contact Us: Mailing Address: Customer Service: DPS Inc. Phone: 877-998-3440 x 538 8015 E. Crystal Dr. Email: cs@dpsi-usa.com Anaheim, CA 92807 Live Chat from our Website...
- Page 14 Digital Peripheral Solutions, Inc. 8015 East Crystal Drive Anaheim, CA 92807 www.Q-See.com Q-See is a registered trademark of Digital Peripheral Solutions, Inc.