Fj Error Messages - Denon AVR-1709 Owner's Manual

ENGLISH
( Step 4 : Check
When analysis is complete, "Parameter Check<" is displayed.
<l
Press and check the analysis results for the following four items.
CD
Make your selection using 1:::. \l and press
• Presence and size of speaker
"SpConfig. Check<"
• Distance of speaker from listening position
"Distance Check<"
• Speaker channel level
"Ch Level Check<"
•
• Crossover Frequency
"CrossoverCheck<"
@ Use 1:::. or \l to change which speaker is displayed.
OTo switch to another analysis result item
ENTER.
Press
This returns you to analysis results items, so repeat operation
o
To proceed to "Step 5 : Store"
During display of crossover frequency result or analysis results item, press
• "Store<" is displayed.
• To proceed to "Step 5" without checking the analysis result, use
while "Parameter Check<" is displayed.
• Values that are different from the actual distance may be set for speakers with built-in filters
(subwoofers, etc). This is because filters add electrical delay to the signal that should be
compensated.
( Step 5 : Store
The auto setup measurement results are stored in the AVR-1709.
CD
<l
Press while "Store<" is displayed.
• "Storing" blinks on the display panel while the results are being stored.
• When storing is complete, "Completed" is displayed followed by "Disconnect Mic".
@ Disconnect the setup microphone from the AVR-1709.
OTo cancel storing
Use 1:::. or \l to display "Cancek" while "Store<" is displayed and press
• All the measured auto setup data will be erased.
-n·..
4
Do not turn the power off while the settings are being stored.
21
<l.
CD.
ENTER.
1:::. \l to select "Store<"
<l.
)
IPJ
Error Messages
If
the auto setup procedure could not be completed due to speaker installation, the measuring environment,
etc. an error message is displayed. Check the relevant items and be sure to take the necessary measures. After
addressing any issues, perform the auto setup procedure over again.
Error messages (examples)
I I·
1'1, '.::' ,- 5 r1 (; n
F : E'
-----'------'------'--=--:..-----'-::...:....-----'------'--'-=-_ _
---..J •
I •
F: ;., b ; en t rj c ; s e
1
-----'-:..:..:..::....:....::..:..-----'----'-'------'--=-=---_ _
---..J
• Speaker or subwoofer sound is too • Check the speaker installation and the
I·
;~
rj co n
C a '-' t ; co n " 5
F
1
---='--'t::....::......:....:.-=--'---=--------'-.:....::.....:...:::.--
The messages alternate
I----'--'-'-FI;· I
)
•
I
t
---=-=-=------=-----'----'------='-=--=------
The messages alternate
~=----
_ _
1---=--=-_, I
L'
Select" Retry" to make the measurements again.
-n...
4
Be sure to turn the power off before checking speaker connections.
Cause
:~~~~~~~~ed ~~~r~~~tone ~~e<SE~~c~u~~g>.
setup microphone is not •
Not all speakers could be detected. • Check the speaker connections.
:~~ur~~c~e:~~~:~:nt~~o ~~o::;ad~r ~~~:r~~~o~: i~~~~~Vice
•
Try again when the surroundings are
•
quieter.
low for accurate measurements to be direction in which the speakers are
made. facing .
• Adjust the subwoofer's volume.
~~~~~~~~d
speaker could not be. Check
displayed speaker.
.
The front L and front R speakers
were not properly detected.
· Only one channel of the surround
speakers was detected.
· Sound was output from the R
channel when only one surround
back speaker was connected.
· The surround back speaker was
detected, but the surrounds were
not detected.
with • Check the polarities of the displayed
Displayed speaker connected
the polarities reversed. speaker.
• For
message may be displayed even if the
speaker is properly connected. If the
connection is correct, use the
buttons to display "Skip<" and then
press
Measures
setup
generating
the connections of the
some speakers, this error
1:::. or \l
<l.