Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for LG BE320-SD
Summary of Contents for LG BE320-SD
- Page 1 DLP Projector BE320-SD Owner's Manual www.lg.com P/N: SAC30190915 Rev. A...
-
Page 2: Table Of Contents
Table of Contents Appendices Table of Contents Troubleshooting ........... 37 Usage Notice Replacing the lamp ..........42 Compatibility Mode ..........44 Safety Instructions ..........2 Computer Compatibility (Analog, PC) ....44 RGB to RCA adapter ........44 Introduction Configurations of Terminals ......... 45 Product Features ........... -
Page 3: Usage Notice
Usage Notice Safety Instructions Please take note of the safety instructions to prevent any poten- tial accident or misuse of the projector. Safety Instructions are given in two forms as detailed below. WARNING : The violation of this instruction may cause serious injuries and even death. NOTES : The violation of this instruction may cause injuries or damage to the projector. After reading this manual, keep it in the place that you can access easily. - Page 4 Usage Notice Power WARNING Never touch the power plug with a Do not plug-in too many items into Prevent dust from collecting on the wet hand one power outlet. power plug pins or outlet. This may cause an electric shock- It may result in overheating of the This may cause a fire hazard! hazard!
- Page 5 Usage Notice Using WARNING If the projector is in a room that Don’t look at laser beam directly as Always open the lens door or experiences a gas leak, do not it can cause eye damage! remove the lens cap when the touch the projector.
-
Page 6: Introduction
Introduction Product Features SVGA (800x600) Native resolution ■ RGB monitor Loop Thru ■ (works on standby mode > 0.5 W) BrilliantColor Technology ■ RS232C control ■ Rapid shutdown ■ This device meets the EMC requirements ments for home applicaces (Class B) and is intended for home usage. This device can be used in all regions. English English... -
Page 7: Package Overview
Introduction Package Overview This projector comes with all the items shown below. Check to make sure your unit is complete. Contact your dealer immediately if anything is missing. Lithium Cell Projector Wireless Remote Control Battery Due to the differ- ence in applications for each country, some regions may have dif- ferent accessories. Battery is included inside the remote con- trol. Power Cable RGB Cable OWNER’S MANUAL PROJECTOR BE320-SD http://www.lg.com P/N 36.8PC01G001-A Copyright © 2012 LGE, All Rights Reserved. User’s Manual English... -
Page 8: Product Overview
Introduction Product Overview 1. Control Panel 2. Zoom Lever 3. Focus Ring 4. Lamp Cover Lamp Cove Screw 6. Remote Sensor 7. Tilt-Adjustable Feet 8. Lens 9. Ventilation (inlet) 10. Ventilation (outlet) English English... -
Page 9: Connection Ports
Introduction Connection Ports 1. VIDEO Connector 4. RS232C Control Port 2. RGB OUT Connector 5. AC IN 3. RGB IN Connector 6. Kensington Lock Kensington Security System T his projector has a Kensington Security System Connector on the back panel. Connect the Kensington Security System cable as below. F or the detailed installation and use of the Kensington Security System, refer to the user’s guide included with the Kensington Security System set. And for further information, contact http://www.kensington.com, the internet homepage of the Kensington company that deals with expensive electronic equipment such as notebook PCs or projectors. T he Kensington Security System is an optional item. English... -
Page 10: Control Panel
Introduction Control Panel Refer to the “Power On/Off the Pro- POWER jector” section on pages 16~17. AUTO Automatically synchronize the projector to the VGA(RGB) and Video signal input sources. Confi rm your item selection. MENU Press “MENU” to launch the on- screen display (OSD) menu. To exit OSD, press “MENU” again. SOURCE Press “SOURCE” to select an input signal. Four Direction- Use or or or to select items al Select Keys or make adjustments to your selec- tion. POWER LED Indicate the projector’s status. TEMP LED Indicate the projector’s temperature status. LAMP LED Indicate the projector’s lamp status. English English... -
Page 11: Remote Control Battery Installation
Introduction Remote Control Battery Installation Procedure 1. Remove the battery holder by holding down the side release fi rmly and pulling out the battery holder. 2. Insert a CR2025 coin cell battery and align the polarity correctly according to the marking in the battery holder. Ensure that the side with a “+” is facing up. Replace the battery holder. When you use the remote control for the fi rst time, there is a plastic sheet between the battery and its contact. Remove the sheet before use. Warning: To ensure safe operation, please observe the following precautions : ■ U se CR2025 type battery. ■ A void contact with water or liquid. ■ D o not expose the remote control to moisture or heat. -
Page 12: Remote Control
Introduction Remote Control You can only turn the projector on/off with POWER button on the projector. You can operate all of the functions of the projector via the remote control. Make sure not to lose the remote control. Infrared trans- Sends signals to the projector. mitter Press “RGB” to choose RGB connec- tor. Refer to the “Power On/Off the Pro- Power jector” section. (refer to pages 16~17) Video Press “Video” to choose VIDEO con- nector. English English... - Page 13 Introduction Sleep Press “Sleep” to set the countdown timer interval. The projector will auto- matically power off when the count- down has finished. (in minutes) Still Pause the screen image. Press again to resume the screen image. Blank Use this function to choose blank color. Menu Press “Menu” to launch the Onscreen display (OSD), back to the top level of OSD for the OSD main menu opera- tion Ratio Use this function to choose your desired aspect ratio. Confirm your section of items in sub menu operation. Four Use to select items or or or Directional or make adjustments to your selec- Select Keys tion.
-
Page 14: Remote Control Operating Range
Introduction Remote Control Operating Range 23.0’ (7m) Approx.15° Point the remote control toward the projector (Infrared Re- mote Receiver) when pressing any button. Maximum operat- ing range for the remote control is about 23.0’ (7m) and 30° in front of the projector. English English... -
Page 15: Installation
Installation Connecting the Projector Connect to Computer/Notebook Due to the differ- ence in applications for each country, some regions may have differ- ent accessories. 1....................... Power cable 2...................Monitor out cable (optional) 3........................RGB cable 4..................RS232C cable (optional) Optional Extras To purchase optional extras, visit an electronics store or online shopping site or contact the retail store where you purchased the product. Without prior notice, optional extras are subject to change in order to improve the performance of the product, and new accessories may be added. English... -
Page 16: Connect To Video
Installation Connect to Video DVD player, Set-top Box HDTV receiver Video Output Due to the differ- ence in applications for each country, some regions may have dif- ferent accessories. ( ) If you want to connect the HDTV, it is recommended to buy the “RGB to RCA adaptor”. 1....................... Power cable 2................Composite video cable (optional) 3..............( ) RGB to RCA adaptor (optional) 4................3 RCA component cable (optional) Optional Extras To purchase optional extras, visit an electronics store or online shopping site or contact the retail store where you purchased the product. Without prior notice, optional extras are subject to change in order to improve the performance of the product, and new accessories may be added. English English... -
Page 17: Powering On/Off The Projector
Installation Powering On/Off the Projector Powering On the Projector 1. Ensure that the power cable and signal cable are securely connected. The POWER LED will turn orange. 2. T urn on the lamp by pressing “POWER ” on the remote control or the control panel . The POWER LED will fl ash green. When disappear startup screen, the POWER LED will turn green. 3. T urn on your source (computer, notebook, video player, etc.) The projector will detect your source automatically. If you connect multiple sources at the same time, press the “SOURCE” button on the control panel to switch between inputs. SVGA English... -
Page 18: Powering Off The Projector
Installation Powering Off the Projector 1. P ress the “POWER ” to turn off the projector, you will see a message as below on the on-screen display. Press the “ POWER ” again to confirm. 3. T he cooling fan continues to operate for cooling cycle and the POWER LED will flash orange. When the POWER LED is orange, the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the projector has completed the cooling cycle and has enter standby mode. Once in standby mode, simply press “POWER ” to restart the projector. 4. D isconnect the power cable from the electrical outlet and the projector. -
Page 19: Adjusting The Projected Image
Installation Adjusting the Projected Image Adjusting the Height of Projector Image The projector is equipped with adjustable feet to raise and lower the image to fi ll the screen. To raise/lower the image: Use “Adjustable feet” to fi ne-tune the display angle You can raise the projector front up by rotating the adjustable feet. Adjustable feet English... -
Page 20: Adjusting The Projector's Zoom And Focus
Installation Adjusting the Projector’s Zoom and Focus To focus the image, rotate the focus ring until the image is clear. The projector will focus at distances from 3.28 to 39.37 feet (1.0 to 12.0 meters) with mechanical travel. To turn the zoom lever to zoom in or out. Zoom Lever Focus Ring Adjusting Projection Image Size Projection Image Size from 22.9” to 255.0” (0.6 to 6.48 meters). Top View Screen Screen (W) Projection Distance (D) Width Screen (H) Screen Side View Offset (Hd) Projection Distance (D) English English... - Page 21 Installation Screen Size W x H Projection Distance (D) Diagonal length Offset (Hd) (inch) size of 4:3 (meter) (inch) (meter) (feet) Screen Width Height Width Height wide tele wide tele (feet) 0.610 0.457 1.183 1.301 3.880 4.268 0.069 0.225 0.813 0.610 1.577 1.735 5.173 5.691 0.091 0.300 1.219 0.914 2.365 2.602 7.760 8.536 0.137...
-
Page 22: User Controls
User Controls On Screen Display The Projector has multilingual On-screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to operate T o open the OSD, press “MENU” on the Remote Control or Control Panel. W hen OSD is displayed, use keys to select any item in the main menu. While making a selection on a particular page, press or key to enter sub menu. 3. U se keys to select the desired item in the sub menu and adjust the settings using key. 4. Select the next item to be adjusted in the sub menu and adjust as described above. 5. Press “OK” to confirm, and the screen will return to the sub menu. 6. T o exit, press “MENU” repeat again. The OSD will be closed and the projector will automatically save the new settings. -
Page 23: Image
User Controls IMAGE Picture Mode T here are many factory presets optimized for various types of im- ages. Use the or to select the item. Presentation: This mode is suitable for showing in front of public in connection to the PC. High-Bright: This mode is recommended when you want maxi- mum brightness. When you change the items, the pic- C lassroom: This mode is recommended for projecting in a class- ture mode will be set room. “User1”. Movie: This mode is suitable for watching video. sRGB: Standardized accurate color. B lackboard: This mode should be selected to achieve optimum color settings when projecting onto a blackboard (green). User1/User2: Memorize user’s settings. Brightness Adjust the brightness of the image. (range: 0~100) Press the to darken image. ... - Page 24 User Controls Press the to decrease the contrast. Press the to increase the contrast. Sharpness Adjust the sharpness of the image. (range: 0~31) “Sharpness”, Press the to decrease the sharpness. “Saturation” and “Hue” functions are Press the to increase the sharpness. only supported under Saturation Video mode. Adjust a video image from black and white to fully saturated color. (range: 0~100) Press the to decrease the amount of color in the image. Press the to increase the amount of color in the image. Hue Adjust the color balance of red and green. (range: 0~100) Press the to increase the amount of green in the image. Press the to increase the amount of red in the image. English English...
-
Page 25: Image | Advanced
User Controls IMAGE | Advanced Gamma T his allows you to choose a gamma table that has been fine-tuned to bring out the best image quality for the input. Film: This mode is recommended for movie Video: This mode is recommended for video or TV. Graphics: This mode is recommended for image. PC: This mode is recommended for presentation. Blackboard: This mode is recommended for using blackboard (green). BrilliantColor P roduces an expanded on-screen color spectrum that delivers en- hanced color saturation for bright, true-to-life images. (range: 0~10) Color Temp. Adjust the color temperature. At cool temperature, the screen looks colder, at warm temperature, the screen looks warmer. At medium temperature screen looks between Cool and Warm temperature. -
Page 26: Image | Advanced | Color
User Controls IMAGE | Advanced | Color Color R ed Gain/Green Gain/Blue Gain/Cyan Gain/Magenta Gain/Yel- low Gain/Red Bias/Green Bias/Blue Bias: Use the or button to select Red, Green, Blue, Cyan, Magenta and Yellow Colors. Then use the or button to adjust the setting. (range: -50~50) Reset Choose “Yes” to return the factory default settings for “Color”. Exit Return to previous menu. IMAGE | Advanced | Input Input Use this option to enable / disable input sources. Press “OK” to en- ter the sub menu and select which sources you require. Press “OK” to finalize the selection. The projector will not search for inputs that are not selected. -
Page 27: Screen
User Controls SCREEN Aspect Ratio Use this function to choose your desired aspect ratio. 4:3: This format is for 4×3 input sources. 16:9: This format is for 16×9 input sources, like HDTV and DVD enhanced for Wide screen TV. 16:10: This format is for 16×10 input sources, like widescreen laptops. 15:9: This format is for non-16×9, letterbox sources and for users who use external 16×9 lens to display 1.67:1 aspect ratio using full resolution. 5 :4: This format is for 5×4 input sources. Native: This format displays the original image without any scaling. AUTO: Automatically selects the appropriate display format. Overscan O verscan function removes the noise in a video image. Overscan the image to remove video encoding noise on the edge of video source. (range: 0~3) Digital Zoom Adjust the size of projector’s display area. (range: -20~100) Press the to reduce the size of an image on the projection screen. Press the to increase an image on the projection screen. English... - Page 28 User Controls H Image Shift Shift the projected image position horizontally. (range: -50~50) V Image Shift Shift the projected image position vertically. (range: -50~50) V Keystone P ress the or to adjust image distortion vertically and makes a rectangular image. (range: -40~40) English English...
-
Page 29: Screen
User Controls SETTING Language C hoose the multilingual OSD. Press or button into the sub menu and then use or or or button to select your pre- ferred language. Press “OK” to finalize the selection. Orientation Front-Desktop T he factory default setting. The image is projected straight on the screen. Rear-Desktop W hen you select this function, the projector reverses the image so you can project behind a translucent screen. Front-Ceiling W hen you select this function, the projector turns the image upside down for ceiling-mounted projection. English... - Page 30 User Controls Rear-Ceiling W hen you select this function, the projector reverses and turns the image upside down at same time. You can project from be- hind a translucent screen with ceiling mounted projection. Menu Location Choose the menu location on the display screen. Projector ID ID definition can be set up by menu (range 0~99), and allow user control an individual projector by RS232C. English English...
-
Page 31: Setting | Signal
User Controls SETTING | Signal Phase Synchronize the signal timing of the display with the graphic card. If the image appears to be unstable or flickers, use this function to correct it. (range: 0~31) “Signal” is only supported in Analog Clock VGA (RGB) signal. Change the display data frequency to match the frequency of your computer’s graphic card. Use this function only if the image appears to flicker vertically. (range: -5~5) H. Position (Horizontal Position) (range: -5~5) Press the to move the image left. Press the to move the image right. V. Position (Vertical Position) (range: -5~5) Press the to move the image down. -
Page 32: Setting | Advanced
User Controls SETTING | Advanced Logo Use this function to set the desired startup screen. If changes are made they will take effect the next time the projector is powered On: LG startup screen. (default) Off: No logo is displayed. Exit Return to previous menu. English English... -
Page 33: Options
User Controls OPTIONS Input Search When “On” is selected, the projector will search for other signals if the current input signal is lost. When “Off” is selected, the projector will only search a specified connection port. Fan Mode AUTO: The built-in fans automatically run at a variable speed according to the internal temperature. High Speed: The built-in fans run at high speed. Information Hide On: Choose “On” to hide the “searching” message. Off: Choose “Off” to show the “searching” message. Blank Color Use this feature to display a “Black”, “Red”, “Green”, “Blue” or “White” screen when no signal is available. Reset Resets all adjustments and settings to their factory settings. English... -
Page 34: Options | Lamp Settings
User Controls OPTIONS | Lamp Settings Lamp Hours Used (Normal) Display the projection time of normal mode. Lamp Hours Used (ECO) Display the projection time of ECO mode. Lamp Life Reminder On: Choose “On” to show the lamp end of life warning message. Off: Choose “Off” to hide the lamp end of life warning message. ECO Mode On: C hoose “On” to dim the projector lamp which will lower power consumption and extend the lamp life. Off: Choose “Off” to increase the brightness. Clear Lamp Hours Reset the lamp hour counter after replacing the lamp. Exit Return to previous menu. English English... -
Page 35: Options | Information
User Controls OPTIONS | Information Source Display the input connector type. All functions in Resolution (Resolution or Video) Information display the status of the Display the current display resolution. projector only. ECO Mode Display the ECO mode. Sleep Countdown Display the countdown timer interval. Exit Return to previous menu. English... -
Page 36: Options | Advanced
User Controls OPTIONS | Advanced Standby Mode Power-Saving: Choose “Standby” to save power dissipation further < 0.5 W. Normal: Choose “Normal” to return to normal standby mode and the “MONITOR OUT” port will be enabled. Direct Power On C hoose “On” to activate Direct Power mode. The projector will automatically power on when AC power is supplied, without POWER pressing the “ ” key on the projector control panel or POWER “ ” key on the remote control. Auto Power Off (min) Sets the countdown timer interval. The countdown timer will start, when there is no signal being sent to the projector. The projector will automatically power off when the countdown has finished. (range: 0~180 mim) Sleep Timer (min) Sets the countdown timer interval. The countdown timer will start, with or without a signal being sent to the projector. The projector will automatically power off when the countdown has finished. (range: 0, 30, 60, 90...360 mim) Auto Standby (hr) Sets the countdown timer interval. The countdown timer will start,... - Page 37 User Controls Control Panel Lock When the control panel lock function is “On”, the control panel will be locked however, the projector can be operated by the remote control. By selecting “Off”, you will be able to reuse the control panel. Press and hold the “OK” button on the projector to turn off “Control Panel Lock”. Exit Return to previous menu. English...
-
Page 38: Appendices
IBM/Lenovo [Fn]+[F7] Asus [Fn]+[F8] HP/Compaq [Fn]+[F4] Dell [Fn]+[F8] NEC [Fn]+[F3] LG [Fn]+[F7] Toshiba [Fn]+[F5] Mac Apple: System Preference Display Arrangement Mirror display If you experience difficulty hanging resolutions or your monitor ... - Page 39 Appendices Problem: The screen of the Notebook or PowerBook com- puter is not displaying a presentation If you are using a Notebook PC: S ome Notebook PCs may deactivate their own screens when a second display device is in use. Each has a different way to be reactivated. Refer to your computer’s documentation for detailed information. Problem: Image is unstable or flickering Adjust the “Phase” to correct it. Refer to the “SETTING|signal” section for more information. Change the monitor color setting from your computer. Problem: Image has vertical flickering bar Adjust the “Clock” to correct it. (refer to pages 30) ...
- Page 40 Appendices Problem: The image is stretched when displaying 16:9 DVD T he projector automatically detects 16:9 DVD and adjusts the aspect ratio by digitizing to full screen with 4:3 default setting. I f the image is still stretched, you will also need to adjust the aspect ratio by referring to the following: P lease select 4:3 aspect ratio type on your DVD player if you are playing a 16:9 DVD. If you can’t select 4:3 aspect ratio type on your DVD player, please select 4:3 aspect ratio in the on-screen menu. Problem: Image is too small or too large M ove the projector closer to or further from the screen. P ress “MENU” button on the remote control or projector panel, go to “SCREEN --> Aspect Ratio” and try the different settings. Problem: Image is reversed S elect “SETTING -->Orientation” from the OSD and adjust the ...
- Page 41 Appendices Problem: LED lighting message POWER-LED LAMP-LED TEMP-LED Message (Green) (Orange) (Red) (Red) Standby (Input power cable) Normal (Power on) Powering up (Warming up) Flashing Power off (Cooling: It can’t accept Flashing any key at this status) Error (Lamp failed) Error (Fan lock) Flashing Error (Over temp.) Error (Color wheel) Flashing Steady light => No light => English...
- Page 42 Appendices Problem: Message Reminders Over temperature - the projector has exceeded its recommended operating temperature and must be allowed to cool down before it may be used. Replacing the lamp - the lamp is about to reach its maximum life- time. Prepare to replace it soon. If this happens, after replacing the lamp, connect the power cord and then press the “POWER ” button on the remote control. This will allow you to turn on the projector. Clear the lamp hours by selecting “OPTIONS” -> “Lamp Settings” -> “Clear Lamp Hours” from the menu. Fan failed - the system fan is not working. English English...
-
Page 43: Replacing The Lamp
Appendices Replacing the lamp The projector will detect the lamp life itself. It will show you a warning message When you see this message, please contact your local reseller or service center to change the lamp as soon as possible. Make sure the projector has been cooled down for at least 45 min- utes before changing the lamp. Warning: Lamp compartment may be hot! Allow it to cool down before changing the lamp! Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shat- ter and cause injury if it is dropped. English... - Page 44 Appendices The screws on the lamp cover and the lamp cannot be removed. Do not touch the glass area of the lamp. Hand oil can cause the lamp to shatter. Use a dry cloth to clean the lamp module if it was accidentally touched. Lamp Replacing Procedure: POWER 1. S witch off the power to the projector by pressing the “ ”. 2. Allow the projector to cool down at least 45 minutes. 3. Disconnect the power cable. 4. Unscrew the one screw on the front cover. 5. Push and slide the top cover and then open the top cover. 6. R emove the 2 screws from the lamp module and pull up the lamp bar. 7. Pull out the lamp module by force. 8. I nstall the new lamp module by reversing the previous steps. 9. A fter replacing the lamp, turn on the power, and select the menu ->...
-
Page 45: Compatibility Mode
Appendices Compatibility Mode Computer Compatibility (Analog, PC) V-Sync H-Sync Modes Resolution (Hz) (kHz) 640 x 350 31.50 640 x 480 31.50 640 x 480 37.90 640 x 480 37.50 720 x 400 31.50 SVGA 800 x 600 35.20 800 x 600 37.90 800 x 600 48.10 800 x 600 46.90 1024 x 768 48.40 1024 x 768 56.50 Please note that using resolutions 1024 x 768 60.00 other than native 800 WXGA 1280 x 768... -
Page 46: Configurations Of Terminals
Appendices Confi gurations of Terminals Terminal: RS232 Pin Assignments Spec. Pin no. (from projector back) Received Data (RXD) Transmitted Data (TXD) English English... -
Page 47: Rs232 Protocol Function List
Appendices RS232 Protocol Function List Projector Return (Pass): P Baud Rate : 9600 Projector Return (Fail): F Data Bits: 8 1. T here is a <CR> after XX=00-99, projector's ID, Parity: None all ASCII commands. XX=00 is for all projectors Stop Bits: 1 2. 0 D is the HEX code Flow Control: None for <CR> in ASCII code. UART16550 FIFO: Disable SEND to projector --------------------------------------------------------------------------------------------------------------------------------------------------------- ASCII Code HEX Code Function Description ~XX00 7E 30 30 30 30 0 3 0D Power ON (Support the command on standby mode) ~XX00 0... - Page 48 Appendices ~XX6 n 7E 30 30 36 3 0 a 0D Overscan n = 0 (a=30) ~ 3 (a=33) ~XX6 n 7E 30 30 36 3 0 a 0D Digital Zoom n = -0 (a=D 3 30) ~ 00 (a=3 30 30) ~XX63 n 7E 30 30 36 33 0 a 0D H Image Shift...
-
Page 49: Read From Projector
Appendices SEND from projector automatically ------------------------------------------------------------------------------------------------------------------------------------------------------------------- ASCII Code HEX Code Function Projector Return Description when Standby/Warming/Cooling/Out of Range/Lamp fail/ INFOn n : 0///3///6/7 = Standby/Warming/Cooling/Out of Range/Lamp fail/ Fan Lock/Over Temperature/Lamp Hours Running Out Fan Lock/Over Temperature/Lamp Hours Running Out ------------------------------------------------------------------------------------------------------------------------------------------------------------------- READ from projector -------------------------------------------------------------------------------------------------------------------------------------------------------------------... -
Page 50: Dimensions
Appendices Dimensions 206.00 Lens center 96.15 29.00 9.00 FOCUS 288.00 Screw holes for ceiling mount 55.00 55.00 Screw: M3 Depth: 7.0 mm 70.80 134.80 153.20 Unit: mm English English... -
Page 51: Specifications
Appendices Specifications Rsolution (Pixel) 800 x 600 Aspect ratio Panel size 0.55” SVGA DMD Projection distance 1.0~12.0 m (Mechanical travel) Throw ratio 1.93~2.15, w/Zoom 1.1x Power supply AC 100 ~ 240 V @ 50/60 Hz • 180W Lamp @ Normal operation • 160W Lamp @ ECO operation Dimension (L x W x H) 220 mm x 288 mm x 77 mm Weight 2.2 kg Operation environment Temperature • Operating: 5°C ~ 40°C • Storage: -20°C ~ 60°C Humidity • Operating: 10~85%RH, non-condensing The specifications • Storage: 5~95%RH, non-condensing listed are subject to change without notice. Connection terminal Video, VGA-OUT, VGA-IN, RS232 (9pin) English... -
Page 52: Regulation & Safety Notices
Appendices Regulation & Safety Notices This appendix lists the general notices of your projector. FCC notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the device and receiver. • Connect the device into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/television technician for help. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. Caution Changes or modifications not expressly approved by the manufacturer could void the user’s authority, which is granted by the Federal Communications Commission, to operate this projector. -
Page 53: Operation Conditions
Appendices Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference and 2. This device must accept any interference received, including interference that may cause undesired operation. Notice: Canadian users This Class B digital apparatus complies with Canadian ICES-003. Remarque à l’intention des utilisateurs canadiens Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada. Declaration of Conformity for EU countries • EMC Directive 2004/108/EC (including amendments) • Low Voltage Directive 2006/95/EC • R & TTE Directive 1999/5/EC (if product has RF function) Disposal instructions Do not throw this electronic device into the trash when discarding.