Yamaha Motif-Rack XS Owner's Manual page 70

Voice Mode
Delay Time
Fade in Time
Hold Time
Fade out Time
LFO Set 1 – 3 Dest
(LFO Set 1 – 3 Destination)
LFO Set 1 – 3 Depth
LFO Set 1 – 3 Element Sw
LFO Set 1 – 3 Depth Offset
LFO Phase Offset
User LFO Cycle
User LFO Slope
70
MOTIF-RACK XS Owner's Manual
Determines the delay time between the moment a Note On message is received and the moment the
LFO takes effect. A higher value results in a longer delay time.
Settings: 0 – 127
Determines the amount of time for the LFO effect to fade in after the Delay time has elapsed. A
higher value results in a slower fade-in. When set to "0," the LFO effect will not fade in and reach the
maximum level immediately after the Delay time has elapsed.
Settings: 0 – 127
Determines the length of time for which the
LFO is held at its maximum level. A higher
value results in a longer Hold time. A
setting of hold produces no fade out.
Settings: 0 – 126, hold
Determines the amount of time for the LFO effect to fade out (after the Hold time has elapsed). A
higher value results in a slower fade-out.
Settings: 0 – 127
Determines the parameters which are to be controlled (modulated) by the LFO Wave. Three
Destinations can be assigned, and you can choose from several parameters per Destination.
Settings: insA1 – insA16, insB1 – insB16, A mod, P mod, F mod, reso, pan, LFOspd
insA1 – insA16, insB1 – insB16, (Effect parameters)
Each parameter of the selected Effect type is modulated cyclically. When one of those parameters is selected, the
corresponding parameter name of the selected Effect type is shown in the display.
A mod (Amplitude Modulation Depth)
A tremolo effect produced by cyclically modulating the volume.
P mod (Pitch Modulation Depth)
A vibrato effect produced by cyclically modulating the pitch.
F mod (Filter Modulation Depth)
A wah effect produced by cyclically modulating the tonal brightness.
reso (Resonance)
A special wah effect produced by cyclically modulating the resonance.
pan
An effect produced by cyclically modulating the stereo pan position.
LFOspd (Element LFO Speed)
When this is selected, the Common LFO speed cyclically modulates the Element LFO speed.
n
If one or more "LFO Set 1 – 3 Element Sw" is set to "off" in the one set on the MOTIF-RACK XS Editor and this
parameter is set to something other than one of the effect parameters, "!" indications are shown at right of the "LFO
Set 1 – 3 Dest" and "LFO Set 1 – 3 Depth" settings. This "!" mark indicates that the settings do not apply to all
Elements.
Determines the LFO Wave Depth for each set.
Settings: 0 – 127
Determines whether or not each Element is to be affected by the LFO on the MOTIF-RACK XS Editor.
When some buttons are set to "on", the appropriate Elements are to be affected by the LFO.
Determines the offset values of the "LFO Set 1
Elements on the MOTIF-RACK XS Editor. If the resultant "LFO Set 1
it will be set to 0, and if the resultant "LFO Set 1
127.
Settings: 0 – 127
Determines the offset values of the "Phase"
parameter in the Wave for the respective
Elements on the MOTIF-RACK XS Editor.
Settings: 0°, 90°, 120°, 180°, 240°, 270°
Determines the amount of steps for creating the wave on the MOTIF-RACK XS Editor.
Settings: 2, 3, 4, 6, 8, 12, 16
Determines the slope or ramp characteristics of the LFO wave on the MOTIF-RACK XS Editor.
Settings: off, up, down, up&down
off ...................................... Creates no slope.
up ...................................... Creates an upward slope.
down.................................. Creates a downward slope.
up&down ........................... Creates an upward then downward slope.
Fade in Hold
Max
3 Depth" parameter (above) for the respective
–
3 Depth" value is less than zero
–
3 Depth" value is greater than 127 it will be set to
–
0° 90° 180° 270°
Phase
240°
120°
Fade out
Time
Time