Statement Of Conformity; Information To User - Shure M367 User Manual

Inputs
IMPEDANCE
Input Designed
for Use With
Mic 19 to 600
Line 10 k
Monitor 1 k
Mix Bus (M367) bal.;
1860 un-
bal.
Mix Bus (M267) 3.5 k
Outputs
IMPEDANCE
Output Designed
for Use With
Mic Low–Z inputs
Line 600
Phones 8 to 200
Mix Bus (M367) bal.;
1860 un-
bal.
Mix Bus (M267) 3.5 k
Equivalent Input Noise
–127 dBV with 150 source, 400 to 20,000 Hz
Output Noise
Master level full CCW: –100 dBV, 400 to 20,000 Hz
Master level full CW: –80 dBV, 400 to 20,000 Hz
Hum and Noise
Equivalent Input: 125 dBV, 20 to 20,000 Hz
Output: –95 dBV (Master CCW); –75 dBV (Master CW), 20 to
20,000 Hz
Common Mode Rejection Ratio
65 dB at 100 Hz, –20 dBV input
Polarity
Mic/Line In to Mic/Line Out
Mic/Line In to Phones
Mic/Line In to Mix Bus (tip)
Monitor to Phones
Mix Bus to Mic/Line Out
Overload and Shorting
Shorted outputs, even for prolonged periods, cause no dam-
age. Microphone inputs of up to 3 Vrms cause no damage.
Line and monitor can withstand signals of up to 30 Vrms.
Input Peak Indicators
6 dB below clipping level
Output Peak Indicator
Lights red at 6 dB below clipping level
Output Clipping Level
+18 dBm at line output into 600
Low–Cut Filters
7 dB down at 150 Hz; 6 dB/octave slope (3 dB down at 260 Hz)
Tone Oscillator
1 kHz 20%
Limiter
Threshold: Switchable: 0, +4, +8, +16 dBm
Attack Time: 1 ms 0.5 ms
Release Time Constant: 100 ms 30 ms
Indicator: Green when limiting by 1 dB or more
Input
Actual Clipping
(Internal) Level
1 k –10 dBV
50 k +36 dBV
13 k 0 dBV
bal.; +23 dBV
1860 un-
bal.
3.5 k –17 dBV
Output
Actual Clipping
(Internal) Level
1 –31 dBV
150 +18 dBm
300 +11 dBV
bal.; +11 dBV
1860 un-
bal.
3.5 k –28 dBV
Non–Inverting
Non–Inverting
Inverting
Non–Inverting
Inverting
Phantom Power
12 V Phantom: 12 V through 340
48 V Phantom : 48 V through 3.4 k
Mixer Power
AC. M367: 100–120 Vac, 50/60 Hz, 100 mA (can be rewired
for 220–240 Vac operation); M367E: 220–240 Vac, 50/60 Hz,
50 mA (can be rewired for 100–120 Vac operation); no–signal
current drain 25 mA
DC; meter illumination off. 18 Vdc nominal at 40 mA typical
no–signal, 45 mA typical at +4 dBm output; 13.5 Vdc minimum;
battery life approximately 8 hours at +4 dBm output in continu-
ous use.*
*Meter not illuminated; no phantom microphones; no headphones.
DC; meter illumination on. 18 Vdc nominal at 70 mA typical
no–signal, 75 mA typical at +4 dBm output; 13.5 Vdc minimum;
battery life approximately 4 hours at +4 dBm output in continu-
ous use.
Batteries. Two 9 V alkaline batteries, type NEDA 1604A (Du-
racell MN1604 or Eveready 522 recommended)
Temperature Range
Operating: –18 to 57 C (0 to 135 F)
Storage: –29 to 74 C (–20 to 165 F)
Overall Dimensions (H x W x D)
71.9 mm x 308 mm x 233 mm (2
ing feet
Weight (without batteries)
3 kg (6.6 lb)

STATEMENT OF CONFORMITY

This certifies that the Shure M367E Microphone Mixer meets
the specifications and regulations embodied in Vfg 243/1991,
amended 1992. The Bundesamt für Zulassungen in der Tele-
kommunikation has been notified that this device has been mar-
keted and has been provided the right to verify the device or sys-
tem for compliance with the specifications.
Conforms to European Union directives, eligible to bear CE
marking; VDE GS-Certified to EN 60 950; meets European Union
EMC Immunity Requirements (EN 50 082–1, 1992): RF radiated
(IEC 801–3): meets Criterion A, ESD: meets Criterion B, EFT
(IEC 801–4): meets Criterion B

INFORMATION TO USER

Changes or modifications not expressly approved by Shure
Brothers Inc. could void your authority to operate this equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device pursuant to Part 15 of the FCC
Rules and as set out in the Radio Interference Regulations of the
Canadian Department of Communications. These limits are de-
signed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guar-
antee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or tele-
vision reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for
help.
6
13 5 5
/ " x 12 / " x 9 / ") includ-
16 32 32