Toshiba Satellite A60 Maintenance Manual

Toshiba Satellite A60 Maintenance Manual

Maintenance manual
Hide thumbs Also See for Satellite A60:
Table of Contents

Advertisement

Toshiba Personal Computer
Satellite A60/ Pro A60
Maintenance Manual
TOSHIBA CORPORATION
S/ No.
Satellite A60/ Pro A60 Maintenance Manual

Advertisement

Table of Contents
loading

Summary of Contents for Toshiba Satellite A60

  • Page 1 Toshiba Personal Computer Satellite A60/ Pro A60 Maintenance Manual TOSHIBA CORPORATION S/ No. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 2 The information presented in this manual has been reviewed and validated for accuracy. The included set of instructions and descriptions are accurate for the Satellite A60/ Pro A60 at the time of this manual's production. However, succeeding computers and manuals are subject to change without notice.
  • Page 3: General

    Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite A60/ Pro A60, referred to as Satellite A60/ Pro A60 in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field.
  • Page 4: Handling The Lcd Module

    The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Satellite A60/ Pro A60 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service.
  • Page 5 Text that you are instructed to type in is shown in the boldface type below: DISKCOPY A: B: The display Text generated by the XXXXX that appears on its display is presented in the type face below: Format complete System transferred Satellite A60/ Pro A60 Maintenance Manual...
  • Page 6: Table Of Contents

    Procedure 1 Replacement Check ............... 2-10 2.5-inch HDD ....................... 2-11 Procedure 1 Message Check ................2-11 Procedure 2 Partition Check ................2-11 Procedure 3 Format Check................. 2-12 Procedure 4 Test Program Check ..............2-13 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 7 IEEE 1394 Test (Optional)................... 2-24 Procedure 1 Test Program Check ..............2-24 Procedure 2 Connector Check ................2-24 2.14 Cooling Module....................2-25 Procedure 1 Test Program Check ..............2-25 Procedure 2 Connector Check and Replacement Check........2-25 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 8 Speaker ......................... 4-42 4.12 Top Cover with the Display Assembly ..............4-46 4.13 I/O Board......................4-50 4.14 System Board ....................... 4-51 4.15 Display Mask......................4-53 4.16 Inverter Board ...................... 4-55 4.17 LCD Module ......................4-57 viii Satellite A60/ Pro A60 Maintenance Manual...
  • Page 9 Appendix B Board Layout ....................B-1 Appendix C Keyboard Scan/Character Codes ..............D-1 Appendix D Key Layout.....................E-1 Appendix E Wiring Diagrams.................... F-1 Appendix F BIOS Rewrite Procedures ................G-1 Appendix G EC/KBC Rewrite Procedures................ H-1 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 10 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 11: Chapter 1 Hardware Overview

    Chapter 1 Hardware Overview...
  • Page 12 1 Hardware Overview 1-ii Satellite A60/ Pro A60 Maintenance Manual...
  • Page 13 1.5 CD-RW/DVD-ROM Drive .................... 1-16 1.6 DVD Multi ........................1-17 1.7 Power Supply ......................... 1-18 1.8 Batteries ......................... 1-19 1.1.1 Main Battery..................1-19 1.1.2 Battery Charging Control ..............1-19 1.1.3 RTC Battery ..................1-20 Satellite A60/ Pro A60 Maintenance Manual 1-iii...
  • Page 14 Table 1- 2 DVD-ROM drive specifications................ 1-15 Table 1- 3 CD-RW/DVD-ROM drive specifications ............1-16 Table 1- 4 DVD-Multi drive specifications................. 1-17 Table 1- 5 Battery specifications ..................1-19 Table 1- 6 Quick/normal charging time................1-20 1-iv Satellite A60/ Pro A60 Maintenance Manual...
  • Page 15: Features

    1 Hardware Overview 1.1 Features The Toshiba Satellite A60/ Pro A60 is a full size notebook PC based on the Intel Portability P4 processor, providing high-speed processing capabilities and advanced features. The computer employs a Lithium Ion battery that allows it to be battery-operated for a longer period of time.
  • Page 16 These ports support PnP installation and hot plugging. External monitor port A 15-pin external monitor port is provided, through which the computer automatically recognizes an external VESA DDC 2B compatible monitor. PC Card slot Satellite A60/ Pro A60 Maintenance Manual...
  • Page 17 PC card HDD boot does Not be supported. SD/MS Card This slot is BTO/CTO for your memory card requirements to provide memory card read on your computer Toshiba Pointing Device Toshiba Pointing Device has one kind of input devices TouchPad. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 18 Fast Serial InfraRed (FIR) communications port(optional) The FIR Port is optional integrated device. It provided an IrDA 1.1 compatible FIR port , enabling wireless communication at a high speed of 1.15 or 4 Mbps. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 19: Figure 1- 1 Parts Description Placement

    1.1 Features 1 Hardware Overview Figures 1-1 and 1-2 show the computer and its system unit configuration, respectively. Figure 1- 1 Parts description placement Satellite A60/ Pro A60 Maintenance Manual...
  • Page 20: Figure 1- 2 The Computer Block Diagram

    1 Hardware Overview 1.1 Features Figure 1- 2 The computer Block diagram Satellite A60/ Pro A60 Maintenance Manual...
  • Page 21: Figure 1- 3 System Board Configuration

    Speaker Phone Card Slot Right Ext. Cooling Modul AC Adapter LCD/FL Inverter System IEEE 1394 MINI PCI Board Touch PAD RJ-45 Keyboard RJ-11 Battery DVD-ROM n Battery Wireless Figure 1- 3 System Board configuration Satellite A60/ Pro A60 Maintenance Manual...
  • Page 22: System Unit Components

    DVD-ROM (02) DVD+RW DVD Super Multi USB P1 PCI-PC Bridge USB P2 Internal LPC EC/KBC Flash (LPC 47N249) Stick Point K/B Main Battery KPA AC E2PROM 1269A Figure 1- 4 System unit block diagram Satellite A60/ Pro A60 Maintenance Manual...
  • Page 23 − 512 MB (16M x 16 x 16P) − 512 MB (32M x 16 x 8P) − 1024 MB (32M x 16 x 16P) • 2.5 volt operation • No parity bit • 64-bit data transfer Satellite A60/ Pro A60 Maintenance Manual...
  • Page 24 − PCI master/slave interface (PCI R2.2 compliant) − PCI IDE controller − Support for ATA-100 (30/40/60/80 GB) − USB interface − SMBus interface − LPC interface − Power management control − Suspend/resume control 1-10 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 25 − Full-duplex (simultaneous record/replay capability) KBC/EC (Keyboard Controller/Embedded Controller) A single LPC 47N249 chip is used to serve as KBC/ EC and Super IO. • KBC − Scan controller function − Interface controller function Satellite A60/ Pro A60 Maintenance Manual 1-11...
  • Page 26 For fax: V.34,V.17,V.29 V.27 and V.21 Channal 2 V.253 Class 1 fax - AC97 interface LAN controller • REALTEK RTL8100CL − Wake-up On LAN support from S3 − PXE boot support − 100BASE-TX support 1-12 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 27 • Support following 2 kinds of mini PCI wireless LAN cards. − IEEE 802.11g(Askey) − IEEE 802.11a/g(Askey) − • Transfer Rate − IEEE 802.11g: max54Mbits/s • Frequency Channel − IEEE802.11g: 2.4GHz Super I/O • LPC 47N249 Satellite A60/ Pro A60 Maintenance Manual 1-13...
  • Page 28: Inch Hdd

    Table 1- 1 2.5-inch HDD specifications Specifications Toshiba HGST Toshiba Toshiba Item MK4025 IC25N040A MK4021GA MK40245G TMR04 Formatted 40.0007GB 40.0007GB 40.0007GB capacity (GB) User data 78,140,160 78,140,160 78,140,160 58,605,120 sectors Bytes/sector Rotational speed (RPM) 4200rpm 4200rpm 4200rpm 4200rpm 1-14 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 29: Dvd-Rom Drive

    Access time (ms) Average random access (ms) 100ms Average full stroke access (ms) Rotational speed (RPM) 5100 Max Data buffer size (Kbytes) Formats supported DVD-R/W, DVD-R (Read),DVD-RAM CD-ROM, CD-R, CD-R (Write), CD-RW (Write) Satellite A60/ Pro A60 Maintenance Manual 1-15...
  • Page 30: Cd-Rw/Dvd-Rom Drive

    Average full stroke access Rotational speed 4,670 Max 5100 Max 3300 Max (RPM) Data buffer size (Mbytes) Formats supported DVD: DVD-ROM(DVD-5,DVD-9,DVD-10,DVD-18),DVD-R Ver.1.0,Ver.2.0,DVD RW(Read Ver.1.1),DVD-RAM(Read Ver.2.1) CD-DA,CD+(E)G,CD-MIDI,CD-TEXT,CD-ROM,CD-ROM XA,MIXED MODE CD,CD-I,CD-I Bridge(Photo CD,Video CD),Muitisession CD(Photo CD,CD-EXTRA,Portfolio,CD-R,CD-RW),CD-R,CD-RW 1-16 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 31: Dvd Multi

    16.7 (PIO mode 4, Multiword DMA mode 2) Access time (ms) Average random access Average full stroke access Rotational speed 4,670 Max 5100 Max (RPM) Data buffer size (Mbytes) Formats supported DVD: DVD-VIDEO,DVD-ROM,DVD,R(3.9G,4.7G),DVDRW(Ver.1.1),DVD- RAM,DVD+R,DVD+RW CD-DA,CD-ROM, CD-R,CD-RW,CD- ROMXA,PhotoCD(muitiSession),Video CD,CD-Extra(CD+),CD-Text Satellite A60/ Pro A60 Maintenance Manual 1-17...
  • Page 32: Power Supply

    • Monitors the voltage output to the system block (load/logic circuit side). • Monitors the voltage, overvoltage, input/output current of the battery pack. • Monitors the internal temperature of the battery pack. • Monitors the supply voltage from the AC adapter. 1-18 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 33: Batteries

    Battery Charging Control Battery charging is controlled by LPC 47N249. When the AC adapter and battery pack are attached to the computer, the LPC 47N249 controls the charge on/off state and detects a full charge. Satellite A60/ Pro A60 Maintenance Manual 1-19...
  • Page 34: Rtc Battery

    The charging time exceeds the fixed limit. 1.1.3 RTC Battery The RTC battery provides power to keep the current date, time and other system information in memory while the computer is turned off. 1-20 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 35: Chapter 2 Troubleshooting

    2 Troubleshooting Chapter 2 Troubleshooting Satellite A60/ Pro A60 Maintenance Manual...
  • Page 36 Procedure 3 Replacement Check ................ 2-8 System Board ......................2-9 Procedure 3 Replacement Check ..............2-10 2.5-inch HDD ....................... 2-11 Procedure 1 Message Check ................2-11 Procedure 2 Partition Check ................2-11 Procedure 3 Format Check................2-12 2-ii Satellite A60/ Pro A60 Maintenance Manual...
  • Page 37: Cooling Module

    IEEE 1394 Test(Optional)..................2-24 Procedure 1 Test Program Check ..............2-24 Procedure 2 Connector Check ................ 2-24 2.14 Cooling Module....................2-25 Procedure 1 Test Program Check ..............2-25 Procedure 2 Connector Check and Replacement Check......... 2-25 Satellite A60/ Pro A60 Maintenance Manual 2-iii...
  • Page 38 2 Troubleshooting Figures Figure 2-1 Basic flowchart ....................2-3 Tables Table 2-1 HDD error code and status................2-13 2-iv Satellite A60/ Pro A60 Maintenance Manual...
  • Page 39: Outline

    3. Cleaning disk kit (for ODD drive cleaning) 4. Bootable CD 5. PC Card loopback connector 6. Multimeter 7. External monitor 8. Headphone 9. Microphone 10. A-BEX TEST DVD 11. Music CD 12. DVD TSD-1 (TOSHIBA EMI DVD Test Media) Satellite A60/ Pro A60 Maintenance Manual...
  • Page 40: Basic Flowchart

    Make sure the Windows® XP Home Edition has been installed on the HDD. Any other operating system can cause the computer to malfunction. Make sure any piece of optional equipment has been installed. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 41 Follow the display diagnostic Message "In Touch with Procedure in Section 2.7 Tomorrow Toshiba" displayed See the previous page to "Password=" displayed ?? delete the password. Follow the HDD diagnostic OS started ?? Procedure in Section 2.5 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 42 Perform the continuous test to check if the error is intermittent. Identify the test resulting in the Any error detected by the error and perform the appropriate diagnostic program ?? diagnostic procedures The system is normal. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 43 10. If an error is detected by the IEEE 1394 test, follow the IEEE 1394 troubleshooting procedures in section 2.13. 11. If an error is detected by the Fan On/Off test, follow the cooling module troubleshooting procedures in Section 2.13. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 44: Power Supply

    Battery LED Power supply status On in Amber Battery being charged On in Green Battery fully charged, with AC adapter connected Blinking in Amber Battery low *1 while driving the computer (at equal intervals) Else Satellite A60/ Pro A60 Maintenance Manual...
  • Page 45 Make sure the DC IN LED goes on in Green. If it does not, go to Procedure 2. Check 2 Make sure the Battery LED goes on in Amber or Green. If it does not, go to Procedure 3. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 46: System Board

    Check 2. Check 2 Replace the system board with a new one. If the battery pack is still not working properly, perform Check 3. Check 3 Replace the CPU with a new one. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 47: Procedure 1 Message Check

    The error message appears when either data stored in RAM to be resumed is lost because the battery has been exhausted or the system board is faulty. If any other error message displays, perform Check 3 Resume failure and press any key to continue Satellite A60/ Pro A60 Maintenance Manual...
  • Page 48: Procedure 2

    Procedure 3 Replacement Check The system board, memory, or CPU may be defective. Disassemble the computer following the steps described in Chapter 4 and replace the system board, memory module or CPU with a new one. 2-10 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 49: Inch Hdd

    Type FDISK and press the Enter key. Choose “Display partition information” from the FDISK menu. If drive C is listed, perform Check 3. If drive C is not listed, return to the FDISK menu and choose the option to create a DOS Satellite A60/ Pro A60 Maintenance Manual 2-11...
  • Page 50 Enter FORMAT C:/S/U to format the HDD and transfer system files. If the following message appears on the display, the HDD has been formatted. Format complete If you cannot format the HDD using the test program, go to Procedure 4. 2-12 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 51: Procedure 4 Test Program Check

    Disk Controller Self Test Failed Disk Controller Test unexpected interrupt Failed Disk Controller action Test Failed disk dos not support SMART disk read attribute threshold error disk read attribute value error disk SMART attribute value error Satellite A60/ Pro A60 Maintenance Manual 2-13...
  • Page 52: Procedure 5 Connector Check And Replacement Check

    The System board may be damaged. Replace it with a new one following the disassembling instructions in Chapter 4. If the problem persists, perform Check 4. Check 4 The CPU may be damaged. Replace it with a new one following the disassembling instructions in Chapter 4. 2-14 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 53: Keyboard

    Chapter 4. If the problem persist, perform Check 5. Check 5 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one. Satellite A60/ Pro A60 Maintenance Manual 2-15...
  • Page 54: Display

    3. If there is still an error, perform Check 2. Check 2 The LCD/FL cable may be faulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 3. 2-16 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 55 The CPU may be faulty. Replace it with a new one following the instructions in Chapter 4. Check 10 The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persist, perform Check 10. Satellite A60/ Pro A60 Maintenance Manual 2-17...
  • Page 56: Odd (Optical Disk Drive)

    CD in the computer's CD, turn on the computer and run the test. Then insert a test ODD (Toshiba-EMI DVD-ROM TEST DISK TSD-1) into the ODD drive. See Chapter 3 for information on how to perform the test.
  • Page 57 Chapter 4. If the problem persist, perform Check 6. Check 6 The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persist, perform Check 3. Satellite A60/ Pro A60 Maintenance Manual 2-19...
  • Page 58: Lan

    Chapter 4. If the problem persist, perform Check 3. Check 3 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one. 2-20 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 59: Sd Card/Memory Stick(Optional)

    Chapter 4. If the problem persist, perform Check 3. Check 3 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one. Satellite A60/ Pro A60 Maintenance Manual 2-21...
  • Page 60: Parallel Port(Optional)

    Chapter 4. If the problem persist, perform Check 3. Check 3 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one. 2-22 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 61: Audio Test

    Chapter 4. If the problem persist, perform Check 5. Check 5 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one. Satellite A60/ Pro A60 Maintenance Manual 2-23...
  • Page 62: Ieee 1394 Test(Optional)

    Chapter 4. If the problem persist, perform Check 3. Check 3 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one. 2-24 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 63: Cooling Module

    Chapter 4. If the problem persist, perform Check 5. Check 4 The CPU may be faulty. Replace it with a new one following the steps in Chapter 4. Satellite A60/ Pro A60 Maintenance Manual 2-25...
  • Page 64 2 Troubleshooting 2.14 Cooling Module Check 5 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one. 2-26 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 65 Chapter 3 Diagnostic Programs...
  • Page 66: Chapter 3 Contents

    LOG Parameters Setting................ 22 3.3.7 Specify LOG Viewer................23 3.3.8 Display LOG File .................. 23 3.3.9 LOG Viewer ..................24 3.3.10 LOG File Sample................... 25 Subtests ........................27 System Test......................... 30 Memory Test....................... 34 Storage ........................39 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 67 3 Diagnostic Programs Video........................... 43 Communication (COMM) ..................52 3.10 Peripheral ........................56 3.11 Error Codes and description..................58 3.12 Quick Test Item List ...................... i Satellite A60/ Pro A60 Maintenance Manual...
  • Page 69: General

    A Service Diagnostic BOOT CD A Formatted FLOPPY DISK A Test Media CD (A-BEX TEST CD-ROM TCDR-702)(for CD-ROM test) A Test Media DVD (Toshiba-EMI DVD-ROM TEST DISK TSD-1) An External Monitor (for DISPLAY test) A CD-ROM Driver (for CD-ROM test)
  • Page 70 50KB spare space in the drive, system will save all log files into the root directory the diskette; otherwise, system will save all log files in the root directory of RAM disk. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 71: Quick Start

    When this item is selected, the system will run the diagnostic programs according to the procedures you defined. When the test is completed, a file named Custom.log will be saved in the defined location. Please see the following example-- Mouse test. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 72 Select ‘Test Mouse’ or press F8 to run the test. The prompt information would be displayed in the screen as below. This test item needs user to verify whether the mouse works normally. The test result will be displayed in the following screen: Satellite A60/ Pro A60 Maintenance Manual...
  • Page 73 CPU Speed Test (Step by Step): Select test item: Select System—CPU—CPU Speed, then, press the Enter key. Parameters Setting Choose the OK button after you set the proper parameters in the following window. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 74 As to the method adopted in CPU Speed test, user should highlight the test item and press Enter to start testing. And the user has to setup the parameters every time before running the test. Using this method, only one test item would be tested at one time. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 75: Keyboard Layout Test

    It requires user to press the key and check whether the key in the screen changes color or not. User can terminate test by typing ‘END’. When testing the ‘Fn’ key, it must press the ‘Enter’ key at the same time. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 76: Hot Key Test

    3.2.7 Memory Card Test Write/Read Test Check whether the Memory card(SD/MS) could be correctly accessed. 3.2.8 DMI Read Read the information from the system’s SMBIOS and display it in the screen as follows: Satellite A60/ Pro A60 Maintenance Manual...
  • Page 77: Dmi Write

    1 line before user’s editing. User can modify the attribute’s value in the 2 line and press Enter to confirm the current edition and continue editing the next attribute. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 78: System Information

    This function is used to read the system information. When the test is completed, a file named System.log will be saved in the defined location. During the reading process, the following screen will be displayed to indicate that the progress is in detection: Satellite A60/ Pro A60 Maintenance Manual...
  • Page 79: View Logs

    On the right column, the configuration information of the highlighted component is listed. Press ESC to exit this program. 3.2.11 View Logs User can enter one choice to view a log file in the screen as follows. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 80: Exit To Ms Dos

    Below is an example of running a test item. It includes the following parts: Diagnostics Windows, Test Status Area, Progress Bar, Error List, Test Item’s Title, Status Bar and Message Box. 1. Diagnostics Windows Satellite A60/ Pro A60 Maintenance Manual...
  • Page 81 When the user calls ABORT ALL, the following message box will prompt for his selecting. 4. Title Bar: Title Bar located at the top of the window, it includes information as follows: Program Name and Its Version: Service Diagnostic Ver1.01; Satellite A60/ Pro A60 Maintenance Manual...
  • Page 82 Break On Error: Display ‘HALT’ as shown in the above screen when ‘Break On Error’ is enabled; Wait On Error: Display ‘WAIT’ as shown in the above screen when ‘Wait On Error’ is enabled; Pause Enable: Display ‘PAUSE’ when “Pause Enable” is enabled; Satellite A60/ Pro A60 Maintenance Manual...
  • Page 83 3.2 Quick Start 3 Diagnostic Programs Manual Interrupt Method: Display ‘Esc: Break’ to tell the user how to manually interrupt the test process. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 84: Options

    Execute all selected test items in this editor. The hot key is F8. If “Interactive” option in batch parameters has not been selected, a warning message would be shown as below: • Edit Batch Parameters Satellite A60/ Pro A60 Maintenance Manual...
  • Page 85: Batch Parameters Configuration

    Exit to DOS Exit the Service Diagnostics Editor and back to DOS. 3.3.2 Batch Parameters Configuration The batch parameters configuration screen can be accessed through Service Diagnostics/OPTIONS -> EDIT BATCH PARAMETERS -> BATCH PARAMETERS: Satellite A60/ Pro A60 Maintenance Manual...
  • Page 86 When the option here is enabled, it would affect all the test items while the same option in “Item Parameters Configuration” only affect that test item. Monitor Battery Life Monitor the remaining battery capacity (percent). Satellite A60/ Pro A60 Maintenance Manual...
  • Page 87: Item's Parameters Configuration

    3.3.3 Item’s Parameters Configuration The test items’ parameters configuration screen can be accessed through Service Diagnostics/Options -> Edit Batch Parameters -> Item’s Parameters-> System- >CPU-> Basic Functionality: • Repeat count Repeat times of the test item. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 88: Load Batch Parameters

    3.3.4 Load Batch Parameters Batch parameter is saved in the script file whose extension name is INI (*.INI). Below is the screen shot of “Load Batch Parameters”. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 89: Save Batch Parameters

    In this window, you can specify the .INI files that you wanted to be edited or modified. 3.3.5 Save Batch Parameters Here you can save the edited or modified content to the batch parameters files. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 90: Log Parameters Setting

    If selecting this parameter, the end time of the test will be recorded. Log Errors Only If selecting this parameter, errors will be recorded only when the test fails. Log Errors Only with Time Satellite A60/ Pro A60 Maintenance Manual...
  • Page 91: Specify Log Viewer

    You can specify the Log file viewer in the Specify Log Viewer screen. The default viewing program of Service Diagnostics is LogView.exe. 3.3.8 Display LOG File You can specify the Log file for viewing in the Display Error Log File screen. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 92: Log Viewer

    In this screen, you can specify a Log file and view it with the viewer designated in Specify LOG Viewer. 3.3.9 LOG Viewer Service Diagnostic Log viewer: ↑, ↓ • Scroll a line backward or forward on the screen. • Page Up, Page Down Satellite A60/ Pro A60 Maintenance Manual...
  • Page 93: Log File Sample

    The following section is a sample of log file: DIAG REPORT <Module Name>: Service Diagnostic Ver 1.01 ... Memory Tester Build Date 2002.12.31 [Walk High] Begin Time: Mon Jan 05 10:45:36 2004 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 94 Begin Time: Mon Jan 05 10:48:54 2004 Touch Pad Test : FAIL ITEM TEST FAIL Function ID :502 Error Code :50202 Error Message :Touch Pad Test Fail End Time: Mon Jan 05 10:49:16 2004 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 95: Subtests

    03 Extended Pattern 01 Read/Write Cycle Test [XWRCycle] 02 Read Cycle Test [XRCycle] 04 Walking 1's Test [WalkHigh] 05 Walking 0's Test [WalkLow] 06 Memory Address [Address] 07 Refresh Test [Refresh] 08 Cache Memory [CacheOne] Satellite A60/ Pro A60 Maintenance Manual...
  • Page 96 [V800600_16] VESA 800x600x64K Mode [V800600_24] VESA 800x600x16M Mode [V800600_32] VESA 800x600x32bit Mode 1024X768 Video Modes VESA 1024x768x256 Mode [V1024768_15] VESA 1024x768x32K Mode [V1024768_16] VESA 1024x768x64K Mode [V1024768_24] VESA 1024x768x16M Mode [V1024768_32] VESA 1024x768x32bit Mode Satellite A60/ Pro A60 Maintenance Manual...
  • Page 97 03 Mac Address Detection [MAC Address] 04 1394 01 GUID Detection [1394 R/W Test] Peripheral 01 Keyboard 01 Keyboard Data Line [KBDataLn] 02 Keyboard Led [KBLED] 03 Keyboard Clock Line [KBClokLn] 02 Mouse 01 TouchPad [MSTpad] Satellite A60/ Pro A60 Maintenance Manual...
  • Page 98: System Test

    CPU Speed Comparison--Whether you want to make a comparison of the CPU speed with the value set in ‘Expected CPU Speed’, you should choose ‘Yes’; otherwise, ‘No’. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 99 Speedstep is a kind of energy-saving running mode that is supported by the Pentium III or above. This test item is to check whether the CPU supports Speedstep function according to the change of the CPU work frequency in different power Satellite A60/ Pro A60 Maintenance Manual...
  • Page 100 This test item is to check whether the system clock/calendar works normally. 4. PCI System This test item is to check whether the bus number, device number and function number in PCI bus are valid. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 101 2. Chipset Fan Speed Test This test item is to check whether Chipset Fan exists or not. If it exists, the test will check the speed of Chipset Fan at the status of Power On or Power Off. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 102: Memory Test

    Special Size, the test of Extended Momory will be taken according to the coverage range that user chooses or time. Extended Memory Start Address (MB) & Extended Memory End Address (MB): Set the range of extended memory that is to be tested, the Satellite A60/ Pro A60 Maintenance Manual...
  • Page 103 1 each time; 7. Incremental / Decrement Test Data Pattern is a series of data whose low byte is increasing data from 0x00 and high byte is decreasing data from 0xFF. Subtest 03 Extended Pattern Satellite A60/ Pro A60 Maintenance Manual...
  • Page 104: Memory Test

    Time Limit(m): Choose or Input the time (minute) of the defined range of the memory to be tested. 1. Write/Read Cycle Test Test by using both read and write instructions. 2. Read Cycle Test Test by using read instructions. Subtest 04 Walking 1’s Test Satellite A60/ Pro A60 Maintenance Manual...
  • Page 105 2. Random Increment Read/Write This test item is to check whether the memory could be correctly accessed with randomized memory address and a series of incremental data. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 106 This test item is to check whether the data bus works normally. Subtest 11 Memory Speed Test This test item is to check the data-transferring rate for the cache memory and the system memory. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 107: Storage

    Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested. Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested. Test Mode—Choose test mode from the following options: Satellite A60/ Pro A60 Maintenance Manual...
  • Page 108 Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested. 3. Performance Check the HDD’s seeking speed and transfer the data rate. 4. Controller Check Satellite A60/ Pro A60 Maintenance Manual...
  • Page 109: Storage

    Check the data transfer rate of the ODD drive. It will read data from the ODD disc and calculate the data transfer rate. This test needs a data CD. 3. Data CD Butterfly Seek Satellite A60/ Pro A60 Maintenance Manual...
  • Page 110 RW under LBA mode with the location address increasing in sequence. 6. Tray Eject Test Check the eject function of the ODD. It will eject the ODD and ask the user to confirm if the operation succeeds. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 111: Video

    It will be displayed as follows:. 2. Text Attribute This test item is to check whether the text attribute of normal, hi-intensity, inverse, and blinking in VGA text mode could be correctly displayed on the screen. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 112 This test item is to check whether the video memory could be correctly written and read in VGA text mode. According to the comparison of written data with read data, the program would report PASS or FAIL. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 113 8 colors). In the test, user is required to respond according to the instruction in the screen. 5. 80 * 25 Text Mode This test item is to check whether 80*25 Text Mode works normally. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 114: Video

    VESA Video Modes This test item is to check whether all the video modes supported by the video card works normally. In the test, user is required to respond following the instruction in the screen. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 115 6. 1600 X1200 Video Modes Test Subtest 04 VESA Video Memory This test item is to check whether VESA video memory could be correctly accessed (write data & read data). Below is the test item’s parameter dialog window: Satellite A60/ Pro A60 Maintenance Manual...
  • Page 116 This test item is to report the system’s Accelerated Graphics Port status and check whether AGP registers works normally. Subtest 07 LCD Panel Test This test item is to check whether there is any fault in its resolution by displaying the RGB gradient color screens. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 117 This test item is to check the video adapter’s composing ability of direct color in high and true color mode. In the test, user is required to respond according to the instruction in the screen. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 118 3.8 Video Subtest 11 DAC/Palette Address This test item is to check the function of DAC registers and Palette registers. In the test, user is required to respond according to the instruction in the screen. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 119 What should be done is to write the data of the type of BitBLT operation and the location of BitBLT source area and destination area into the BitBLT registers, and all those operations will be completed automatically by BitBLT engine with minimum CPU intervention. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 120: Communication (Comm)

    Check whether the data register and control register works normally. 2. IRQ Check Check whether LPT interrupt works normally. 3. External Loop back Check whether there is open or short circuit issue. 4. ECP Mode Satellite A60/ Pro A60 Maintenance Manual...
  • Page 121 Prepare a Master whose IrDA works normally, then run the test item in ‘Comm/IrMaster’ under Diagnostics menu; the master stays here to wait for slave requesting. Prepare a slave. User should choose the test item ‘Comm/IrSlave’ and set parameters. Below is the Slave Testing window. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 122 This test item is to check whether the module can detect the existence of the network card and display its related information. 1. Device ID Detection Detect the device ID of the network card. 2. Vendor ID Detection Satellite A60/ Pro A60 Maintenance Manual...
  • Page 123 Detect the vendor ID of the network card. 3. MAC Address Detection Detect the MAC address of the network card. Subtest 04 1394 GUID Detection This test item is used to read and display GUID from 1394 register. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 124: Peripheral

    Check whether the keyboard clock line works normally. Subtest 02 Mouse Test Check whether the point devices work normally. 1. Touch Pad Before test Touch Pad’s function, user should set a timeout time at below screen: Satellite A60/ Pro A60 Maintenance Manual...
  • Page 125 At the below screen of Touch Pad test, user can press the left button, right button, and move the mouse to verify its functions for times, and the test will end either by user break or test time is out. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 126: Error Codes And Description

    Change Error change of power mode. The CPU MMX register is MMX Test Error Replace the CPU. damaged. 02xx Memory The ROM BIOS has Physical Test this unit on multiple Read Error problems. machines. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 127 The frequency is beyond the Periodic Faster Error As above. standard. The frequency is below the Periodic Slower Error As above. standard. Update-ended Interrupt R/W errors with the RTC As above. Error refreshing interrupt controller. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 128 Check whether there is any Physical problems with the video Character Test Error physical problem with the video card. card. DAC/Palette Address Test As above. As above. Error Satellite A60/ Pro A60 Maintenance Manual...
  • Page 129 8bits Video Mode Test As above. As above. Error 15bits Video Mode Test As above. As above. Error 16bits Video Mode Test As above. As above. Error 24bits Video Mode Test As above. As above. Error Satellite A60/ Pro A60 Maintenance Manual...
  • Page 130: Audio

    09xx Keyboard Keyboard Map & Stroke Keyboard Map & Stroke Test Check the KBD connection and Test Fail fails. repeat the test. Clock Line Test Fail Clock Line Test fails. As above. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 131 Memory Card is damaged. repeat the test. Start Flash Media Tests As above. As above. Fail Verifying Firmware As above. As above. loaded Fail MMC or SD Media Card As above. As above. Present Fail Satellite A60/ Pro A60 Maintenance Manual...
  • Page 132 ROM for repair. CD Seek Error Either the disk or the CD-ROM Replace the disk or send the CD- is damaged. ROM for repair. Eject Error Wrong CD-ROM drive. Exit from the wrong drive. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 133: Quick Test Item List

    VESA Video Memory 10% or 3 minutes Color Purity Test Direct Color Test LCD Panel Sequential/Random R/W 25% or 3 minutes SMART Check LAN Card Device ID Detection Vendor ID Detection Mac Address Detection Satellite A60/ Pro A60 Maintenance Manual...
  • Page 134 Chapter 4 Replacement Procedures...
  • Page 135 4 Replacement Procedures 4-ii Satellite A60/ Pro A60 Maintenance Manual...
  • Page 136 Removing the HDD ................... 4-20 Installing the HDD..................... 4-22 Switch Cover and Hotkey Board ................4-23 Removing the Switch Cover and Hotkey Board..........4-23 Installing the Switch Cover and Hotkey Board ..........4-24 Keyboard........................4-25 Satellite A60/ Pro A60 Maintenance Manual 4-iii...
  • Page 137 Removing the North Bridge thermal module and MDC cable ......4-45 Installing the North Bridge thermal module and MDC cable......4-46 4.14 Display Mask ......................4-47 Removing the Display Mask................4-47 Installing the Display Mask ................4-48 4.15 FL Inverter Board ....................4-49 4-iv Satellite A60/ Pro A60 Maintenance Manual...
  • Page 138 LED Board ....................... 4-58 Removing the LED Board ................. 4-58 Installing the LED Board ................... 4-59 4.18 Touch Pad Board...................... 4-60 Removing the Touch Pad Board ................ 4-60 Installing the Touch Pad Board ................. 4-60 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 139 Figure 4-26 Removing the CPU ..................4-40 Figure 4-27 Installing the CPU.................... 4-41 Figure 4-28 Securing the CPU..................... 4-42 Figure 4-29 Removing the system board ................4-43 Figure 4 -30 Removing the North Bridge thermal module..........4-45 4-vi Satellite A60/ Pro A60 Maintenance Manual...
  • Page 140 Figure 4-39 Removing the 14.0-inch LCD module ............. 4-56 Figure 4-40 Removing the 14.0-inch LCD module ............. 4-56 Figure 4-41 Removing the LED board ................4-58 Figure 4-42 Removing the touch pad board ................ 4-60 Satellite A60/ Pro A60 Maintenance Manual 4-vii...
  • Page 142: General

    LAN card, all of which are shown above the top cover with the display assembly. • For removing the LCD Module First, remove the display mask and FL inverter board, both of which are shown above the LCD module. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 143: Safety Precautions

    DANGER: Always use the genuine batteries or replacement batteries authorized by Toshiba. Batteries other than those differ in specifications and are incompatible with the computer. They may burst or explode. Never heat or disassemble the battery packs to avoid leakage of alkaline solutions.
  • Page 144 Inside the PC are components that become hot during operation (such as the CPU and cooling module). To avoid burns, let the hot components cool down before starting inspection or repair task. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 145: Before You Begin

    See the appropriate explanations and figures for screw sizes. To avoid personal injury, use care to handle components that have sharp edges or corners. After you have replaced an FRU, check that the FRU works correctly to ensure normal computer operation. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 146: Disassembly Procedures

    Check that all the required screws are used to fix the FRUs. Using wrong screws can damage the threads or heads of the screws or does not ensure firm FRU fixing. After installing an FRU, make sure that the FRU and computer can work normally. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 147: Tools And Equipment

    0.22 N・m (2.2 kgf・cm) M2.5 (2.5 mm) 0.36 N・m (3.5 kgf・cm) M3 (3 mm) 0.51 N・m (5.0 kgf・cm) M2.5x4 PSP TITE screws 0.204 N・m (2.0 kgf・cm) M2.5x6 GIZA TITE screws 0.36 N・m (3.5 kgf・cm) Satellite A60/ Pro A60 Maintenance Manual...
  • Page 148: Colors Of Screw Shanks

    U (stands for unique-pan head screws, studs, etc.) Symbol examples 6 mm bind screw 12 mm bind screw 5 mm stud (The numeral represents the rounded length of the threaded portion irrespective of the entire stud length.) Satellite A60/ Pro A60 Maintenance Manual...
  • Page 149: Removing The Battery Pack

    3. Slide the battery release latch and remove the battery pack from the computer. Figure 4-1 Removing the battery pack NOTE: Dispose of the used battery packs as required by local ordinances or regulations. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 150: Installing The Battery Pack

    NOTE: Visually check the battery's terminals. If they are dirty, clean them with a dry cloth. 1. Gently insert a new or recharged battery pack into place. Check that the battery release latch slides in and stops with a click. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 151: Removing The Optional Pc Card

    1. Push the eject button for the PC card to be removed until it stops and release the button. 2. When the eject button popped out slightly, push it again. 3. When the PC card popped out, grasp it and pull it out. Figure 4-3 Removing the PC card 4-10 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 152: Installing The Optional Pc Card

    2. After checking that the PC card is seated securely, push the PC card release lever slightly. After the PC card is installed, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the PC card in compatible with the current hardware configuration. Satellite A60/ Pro A60 Maintenance Manual 4-11...
  • Page 153: Removing The Optional Memory

    2. Remove one M2.5x4 black bind screw. 3. Remove the memory cover. CAUTION: Do not touch the connectors on the memory modules or in the computer. Contaminated connectors can cause memory access problems. Figure 4-4 Removing the memory cover 4-12 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 154 4. Spread out the two memory lock stoppers so that the memory module can be raised. 5. Pull the memory module up and out at an angle, using care to the connectors. Figure 4-5 Removing the optional memory Satellite A60/ Pro A60 Maintenance Manual 4-13...
  • Page 155: Installing The Optional Memory

    TSETUP program to make sure that the installed memory module has been recognized by the system. If it has not been recognized yet, check the connections. CAUTION: To prevent system malfunctions, always use Slot a first to insert the memory modules. 4-14 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 156: Removing The Mdc Card

    2. Remove the M2.5x4 black bind screws. 3. Remove the MDC cover. CAUTION: Do not touch the connectors on the MDC card or in the computer. Contaminated connectors can cause MDC card failures. Figure 4-6 Removing the MDC cover Satellite A60/ Pro A60 Maintenance Manual 4-15...
  • Page 157 5. Raise the MDC card and disconnect it from CN502 on the system board. 6. Disconnect the MDC cable from the connector JP1 on the MDC card. Figure 4-7 Removing the MDC card 4-16 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 158: Installing The Mdc Card

    After the computer is turned on, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the installed MDC card has been recognized by the system. If it has not been recognized yet, check the connections. Satellite A60/ Pro A60 Maintenance Manual 4-17...
  • Page 159: Wireless Lan Card

    5. Spread out both the left and right stoppers for fixing the wireless LAN card until the card can be raised. 6. Pull the wireless LAN card up and out at an angle. Figure 4- 8Removing the wireless LAN card cover 4-18 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 160: Installing The Wireless Lan Card

    CAUTION: Do not touch the connectors on the wireless LAN card and in the computer with bare hands. Wireless LAN cards can fail if they are contaminated with sweat, natural oils, etc. from your hands. Satellite A60/ Pro A60 Maintenance Manual 4-19...
  • Page 161: Hdd

    1. Remove one M2.5x3.5 black flat-head screw for fixing the HDD cover. 2. Remove the HDD cover. 3. Remove the HDD pack sliding it in the direction of the arrows. Figure 4-10 Removing the HDD pack cover 4-20 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 162 5. Place the HDD pack on a flat surface (such as a desk), and remove the two M3x4 black flat-head screws. 6. Remove the HDD bracket. Figure 4-12 Removing the HDD chassis CAUTION: Do not apply pressure to the top or bottom of the drive. Satellite A60/ Pro A60 Maintenance Manual 4-21...
  • Page 163: Installing The Hdd

    2. Install the HDD pack into the correct position in the computer. Connect the HDD pack to the computer, holding the HDD pack by its sides. 3. Insert the HDD pack. 4. Secure the HDD cover with one M2.5x4 black flat-head screw. 4-22 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 164: Switch Cover And Hotkey Board

    4. Disconnect the SUMI-card (flat cable) from CN2001 on hotkey board. Figure 4-13 removing the switch cover screw Remove the two M2.5 x4 black flat-head screws for securing the hotkey board. Remove the hotkey board. Satellite A60/ Pro A60 Maintenance Manual 4-23...
  • Page 165: Installing The Switch Cover And Hotkey Board

    4. Place the switch cover in the correct position and secure the following 11 latches, in that order: - Six bottom latches - One latch on the left and right sides - Three front latch 4-24 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 166: Keyboard

    2. Move the keyboard in the direction of the arrow until the keyboard connector appears. 3. Turn the keyboard upside down. 4. Disconnect the keyboard cable from CN16 on the system board and remove the keyboard. Satellite A60/ Pro A60 Maintenance Manual 4-25...
  • Page 167: Installing The Keyboard

    1. Connect the keyboard cable to CN16 on the system board. 2. Align the latches on the rear of the keyboard with the latch holes on the top cover. 3. Secure the keyboard with the two M2.5x3 black bind screws. 4-26 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 168: Odd Bay Modules

    4. Push out the ODD bay module in the direction of the arrow. CAUTION: Handle the ODD bay module carefully, because it becomes hot during operation. Figure 4-16 Removing the ODD bay module Satellite A60/ Pro A60 Maintenance Manual 4-27...
  • Page 169: Installing The Odd Bay Module

    1. Place the ODD bay module in the correct position and slide it in. 2. Push it until it clicks into place. 3. Close the display and turn the computer over. 4. Fix the ODD bay module with one M2x8 black bind screw. 4-28 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 170: Disassembling The Odd Drive

    Figure 4-18 Removing the bracket from the ODD drive Assembling the ODD Drive Assemble the ODD drive according to the following procedures and Figures 4-18. 1. Secure the bracket with the two M2x3 white flat-head screws. Satellite A60/ Pro A60 Maintenance Manual 4-29...
  • Page 171: Display Assembly

    3. Remove four M2.5x4 black flat-head screws and M2x3 white flat-head screw. 4. Disconnect the LCD/FL cable from CN13 on the system board. 5. Remove the wireless antenna cables from the hole. 6. Remove the display module. 4-30 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 172: Installing The Display Assembly

    3. Securing display assembly with four M2.5x4 black flat-head screws. 4. Close the display panel and turn the computer upside down and fix it with two M2.5x20 black bind screws. Satellite A60/ Pro A60 Maintenance Manual 4-31...
  • Page 173: Top Cover

    - Two M2.5x14 black bind screws - Twelve M2.5x6 black bind screws - Eleven M2.5x3 black flat-head screws Figure 4-21 Removing the screws from the bottom of the computer 2. Restore the normal computer placement. 4-32 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 174 4.8 Top Cover 4 Replacement Procedures Figure 4-22 Removing the top cover 3. Disconnect the LED board flat cable from CN17. 4. Lift up the top cover. 5. Disconnect the lid switch cable from CN23. Satellite A60/ Pro A60 Maintenance Manual 4-33...
  • Page 175: Installing The Top Cover

    3. Connect the LED board flat cable to CN17 on the system board. 4. Turn the computer upside down and fix it with the following 25 screws: - Two M2.5x14 black bind screws - Twelve M2.5x6 black bind screws - Eleven M2.5x3 black flat-head screws 4-34 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 176: Speakers

    2. Remove the speaker cables from the guides (grooves) on the bottom cover. 3. Disconnect the speaker cables from CN20 on the system board. 4. Remove the left and right speakers. Figure 4-23 Removing the speakers Satellite A60/ Pro A60 Maintenance Manual 4-35...
  • Page 177: Installing The Speakers

    1. Connect the speaker cables to CN20 on the system board. 2. Place the left and right speakers in their correct position and push the speaker cables into the guides on the top cover. 3. Stick the speaker cables by the tape. 4-36 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 178: Cooling Module

    2. Release the one screw next to the fan. 3. Release the four screws on the cooling module using the numbered order shown to the screw. 4. Remove the cooling module. Figure 4-24 Removing the cooling module Satellite A60/ Pro A60 Maintenance Manual 4-37...
  • Page 179: Installing The Cooling Module

    Please according to the number sequence sealed on heatsink module and secure the relevant screws on the mainboard. NOTE: Apply silicon greases with a special syringe to cover the surface of the CPU chip completely. Figure 4-25 Applying silicon greases 4-38 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 180 3. Secure the four screws on the cooling module using the numbered order shown on the screws. 4. Secure one screw next to the fan. 5. Connect the cooling module cable to CN14 on the system board. Satellite A60/ Pro A60 Maintenance Manual 4-39...
  • Page 181: Cpu

    1. Unlock the CPU by rotating the bar on the CPU socket 90 degrees to the up with hand (in the order shown in the figure below). 2. Remove the CPU. NOTE: After the CPU is removed, should lower the bar before proceeding to prevent damage. Figure 4-26 Removing the CPU 4-40 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 182: Installing The Cpu

    2. Attach the CPU to the correct position in the CPU socket. Align the CPU with the CPU socket by using the triangle as a guide. Figure 4-27 Installing the CPU CAUTION: Place the CPU by aligning the triangle with the shaded area. Satellite A60/ Pro A60 Maintenance Manual 4-41...
  • Page 183 4 Replacement Procedures 4.11 CPU 3. Secure the CPU by rotating the bar 90 degrees to the down with hand. Figure 4-28 Securing the CPU 4-42 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 184: System Board

    4. Remove the lever of the wireless kill switch. 5. Remove two M2.5x4 black flat-head screws for securing the system board. 6. Remove the system board. Figure 4-29 Removing the system board Satellite A60/ Pro A60 Maintenance Manual 4-43...
  • Page 185: Installing The System Board

    4. Seat the HDD tray and secure it with one M2.5x4 black flat-head screw. 5. Press the kill switch button through the opening in the side. Be sure the prongs are fully engaged. 4-44 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 186: North Bridge Thermal Module

    3. Remove two M2x3 black bind screws and washers. 4. Remove North Bridge thermal module. 5. Remove the black sheet. 6. Remove one M2.5x2.5 white bind screws. 7. Removing the CD tray. Figure 4 -30 Removing the North Bridge thermal module Satellite A60/ Pro A60 Maintenance Manual 4-45...
  • Page 187 6. Secure the two washers and M2x3 black bind screws. 7. Place the CD tray in the correct position. 8. Secure one M2.5x2.5 white bind screws. 9. Stick the black sheet in the correct position. 4-46 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 188: Display Mask

    3. Release the following 18 latches on the display mask, in that order: - Four bottom latches - Five latches on each of the left and right sides - Six top latches Figure 4-32 Removing the display mask Satellite A60/ Pro A60 Maintenance Manual 4-47...
  • Page 189: Installing The Display Mask

    3. Place the display mask in the correct position and fasten the following 8 seals, in that order: - Four black seals on the bottom - Four black seals on the top 4-48 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 190: Fl Inverter Board

    Figure 4-33 Removing the FL inverter board 2. Raise the FL inverter board and disconnect the LCD/FL cable from LCD/FL connecter. 3. Disconnect the HV cable from HV connecter and remove the FL inverter board. Satellite A60/ Pro A60 Maintenance Manual 4-49...
  • Page 191: Installing The Fl Inverter Board

    1. Connect the LCD/FL cable to LCD/FL connecter, and connect the HV cable to HV connecter. 2. Place the FL inverter board in the correct position. 3. Fasten the M2.5x4.5 black flat-head screw to secure the FL inverter board. 4-50 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 192: Lcd Modules

    LCD module. 2. Carefully tilt the LCD module toward you. 3. Remove the three M2x3 black bind screws on each of the left and right sides for fixing the LCD bracket. Satellite A60/ Pro A60 Maintenance Manual 4-51...
  • Page 193 4 Replacement Procedures 4.16 LCD Module Figure 4-35 Removing the 15.0-inch LCD module and screws 4-52 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 194 4. Remove the LCD brackets. 5. Turn the LCD upside down. 6. Remove the LCD/FL cable connector. Then disconnect the LCD/FL cable. Figure 4-36 Removing the 15.0-inch LCD module Figure 4-37 Removing the 15.0-inch LCD module Satellite A60/ Pro A60 Maintenance Manual 4-53...
  • Page 195: Installing The 15.0-Inch Lcd Module

    5. Place the LCD module in the correct position and secure it with the two M2.5x4.5 black flat-head screws and two M2x5 white bind screws. 4-54 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 196: Removing The 14.1-Inch Lcd Module

    2. Carefully tilt the LCD module toward you. 3. Remove the three M2x3 black bind screws on each of the left and right sides for fixing the LCD bracket. Figure 4-38 Removing the 14.0-inch LCD module and screws Satellite A60/ Pro A60 Maintenance Manual 4-55...
  • Page 197 4 Replacement Procedures 4.16 LCD Module 4. Remove the LCD/FL cable connector. Then disconnect the LCD/FL cable. Figure 4-39 Removing the 14.0-inch LCD module Figure 4-40 Removing the 14.0-inch LCD module 4-56 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 198: Installing The 14.0-Inch Lcd Module

    3. Place the LCD module in the correct position and secure it with the two M2.5x4.5 black flat-head screws and two M2x5 white bind screws. Satellite A60/ Pro A60 Maintenance Manual 4-57...
  • Page 199: Led Board

    4. Disconnect the touch pad flat cables from J1 on the touch pad and remove the LED board. 5. Disconnect the touch pad flat cables from CN2000 and LED board flat cable from CN2002 on the LED board. Figure 4-41 Removing the LED board 4-58 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 200: Installing The Led Board

    3. Secure LED board to top cover with two M2.5x3 black flat round bind screws. 4. Stick touch pad flat cable by ESD tape on touch pad left side. 5. Stick LED board flat cable by ESD tape. Satellite A60/ Pro A60 Maintenance Manual 4-59...
  • Page 201: Touch Pad Board

    Install the Touch Pad Board according to the following procedures and Figure 4-42. 1. Place the touch pad board in the correct position. 2. Secure the touch pad board with the two M2.5x4 black flat-head screws. 4-60 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 202 次 6000 1 Appendices...
  • Page 203 Appendices App-ii Satellite A60/ Pro A60 Maintenance Manual...
  • Page 204 CN502 MDC I/F Connector (30-pin)..............C-11 C.20 CN503 Memory Slot Connector (202-pin) ............C-12 C.21 CN2000 Touch Pad Connector (12-pin) ............. C-15 C.22 CN2002 LED Connector (24-pin)............... C-15 C.23 JACK1 DC_IN Connector (2-pin) ..............C-15 Satellite A60/ Pro A60 Maintenance Manual App-iii...
  • Page 205: Ec/Kbc Rewrite Procedures

    C.24 JACK2 Ext_Microphone Connector (6-pin) ............C-16 C.25 JACK3 Headphone Connector (6-pin)..............C-16 Appendix D Keyboard Scan/Character Codes..............D-1 Appendix E Key Layout .....................E-1 Appendix F BIOS Rewrite ....................F-1 Appendix G EC/KBC Rewrite Procedures..............G-1 App-iv Satellite A60/ Pro A60 Maintenance Manual...
  • Page 206: Appendix A Handling The Lcd Module

    LCD cover before securing the module with four screws. Do not force the module into place, because stress can affect its performance. Also, the panel’s polarized surface is easily scarred, so be carefully when handling it. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 207 Also, never scratch the surface. 4. If water or other liquid is left on the panel’s surface for a long period, it can change the screen’s tint or stain it. Be sure to quickly wipe off any liquid. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 208 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 209 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 210 9. Do not disassemble the LCD module. Disassembly can cause malfunctions. 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panel’s polarization. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 211 Appendices Apx. A Handling the LCD Module Satellite A60/ Pro A60 Maintenance Manual...
  • Page 212: Appendix B Board Layout

    Appendix B Appendix B Board Layout System Board Front View Figure B-1 Board layout (front) Table B-1 System board connectors (front) Satellite A60 Maintenance Manual...
  • Page 213 USB I/F Connector C JACK2 Ext_Microphone Connector Headphone Connector JACK3 Keyboard Connector Internal CN17 LED Status and IR Connector Keyboard Connector CN16 Internal Battery Bay Connector CN19 CN22 BIOS Chip Connector CN15 Cooling Module Connector Satellite A60/ Pro A60 Maintenance Manual...
  • Page 214 Apx. B Board Layout Appendices Figure B-2 Board layout ( back ) Table B-2 System board ICs and connectors (back) Satellite A60/ Pro A60 Maintenance Manual...
  • Page 215 Appendices Apx. B Board Layout Mark Number Name MINI PCI Connector A’ CN501 MDC Connector B’ CN502 C’ CN504 Serial Connector D’ CN503 Memory Slot A Connector Satellite A60/ Pro A60 Maintenance Manual...
  • Page 216: Appendix C Pin Assignments

    Table C-2 External monitor connector pin assignments (15-pin) Pin No. Signal Name Pin No. Signal Name GREEN BLUE VGA GND VGA GND VGA GND VGA GND +V5S VGA GND DDC DATA CRT_HSYNC CRT_VSYNC DDCCLK Satellite A60/ Pro A60 Maintenance Manual...
  • Page 217: Cn3 Rj45 (12-Pin+4Led

    /USB_PN0_B /USB_PP0_B DGND DGND DGND DGND DGND CN6 TV OUT Connector (4-Pin) Table C-5 TV OUT connector pin assignments (4-pin) Pin No. Signal Name Pin No. Signal Name DGND DGND LUMA_Y CHROMA_C DGND DGND Satellite A60/ Pro A60 Maintenance Manual...
  • Page 218: Cn7 Pc Card Slot Connector (68-Pin

    DGND /A_CD1# /A_CDAT(11) /A_CDAT(12) /A_CDAT(13) /A_CDAT(14) /A_CDAT(15) /A_CE2# /A_VS1 /A_IORD# /A_IOWR# /A_CADR(17) /A_CADR(18) /A_CADR(19) /A_CADR(20) /A_CADR(21) ACARDVCC ACARDVPP /A_CADR(22) /A_CADR(23) /A_CADR(24) /A_CADR(25) /A_VS2 /A_RESET /A_WAIT# /A_INPACK# /A_REG# /A_BVD2_SPKR /A_BVD1_STSCHG_R /A_CDAT(8) /A_CDAT(9) /A_CDAT(10) /A_CD2# DGND Satellite A60/ Pro A60 Maintenance Manual...
  • Page 219: Cn9 Sd/Ms Connector (23-Pin

    Table C-7 SD/MS connector pin assignments (23-Pin) Pin No. Signal Name Pin No. Signal Name /SD_DAT3 /SD_CMD DGND VCC_CARD /SD_MS_CLK DGND /SD_DAT0 /SD_DAT1 /SD_DAT2 /SD_CD# DGND /SD_WP DGND DGND /MS_BS VCC_CARD /MS_SDIO /MS_INS# /SD_MS_CLK VCC_CARD DGND Satellite A60/ Pro A60 Maintenance Manual...
  • Page 220: Cn11 Usb I/F Connector-C (4-Pin

    /SDD_R(3) /SDD_R(13) /SDD_R(2) /SDD_R(14) /SDD_R(1) /SDD_R(15) /SDD_R(0) /SDDRQ_35_R DGND /SDIOR#_3_R /SDIOW#_3_R DGND /SDIORDY_35_R /SDDACK#_35_R /IRQ15_3_R /SDA_R(1) /SDA_R(0) /SDA_R(2) /SDCS1#_3_R /SDCS3#_3_R /MBDASP#_5 +V5S +V5S +V5S +V5S +V5S DGND DGND DGND DGND DGND DGND DGND DGND Satellite A60/ Pro A60 Maintenance Manual...
  • Page 222: Cn13 Lcd/Fl Inverter Connector (42-Pin

    /INV_PWM_3 /BLON# DGND DGND DGND DGND DGND C.11 CN14 Cooling Module Connector (1) (3-Pin) Table C-11 Cooling Module connector (1) pin assignments (3-Pin) Pin No. Signal Name Pin No. Signal Name +V5S DGND /FAN_TACH1 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 224: Cn15 Cooling Module Connector (2) (3-Pin

    Pin No. Signal Name +V5S +V5S /SCAN_OUT(4) /SCAN_OUT(2) /SCAN_IN(2) /SCAN_IN(1) /SCAN_OUT(1) /SCAN_OUT(0) /SCAN_IN(0) /SCAN_IN(3) /SCAN_OUT(5) /SCAN_OUT(6) /SCAN_IN(5) /SCAN_IN(6) /SCAN_IN(4) /SCAN_OUT(12) /SCAN_OUT(7) /SCAN_OUT(3) /SCAN_IN(7) /SCAN_OUT(13) /SCAN_OUT(9) /SCAN_OUT(8) /SCAN_OUT(11) /SCAN_OUT(10) /SCAN_OUT(14) /SCAN_OUT(15) +V5S /CAPS_LED#_3 /SCROLL_LED#_3 /NUM_LED#_3 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 226: Cn18 Hdd Connector (44-Pin

    +V5S +V5S DGND DGND DGND C.15 CN19 Main Battery Connector (7-Pin) Table C-15 Main battery connector pin assignments (7-Pin) Pin No. Signal Name Pin No. Signal Name +VBAT +VBAT BATT_SCL BATT_SDA THRM0 DGND DGND Satellite A60/ Pro A60 Maintenance Manual...
  • Page 227: Cn20 Internal Left Speaker Connector (4-Pin

    CN501 MINI PCI Connector (126-Pin) Table C-18 MINI PCI connector pin assignments (126-Pin) (1/3) Pin No. Signal Name Pin No. Signal Name WLON DGND /PIRQB#_3 +V5S /PIRQB#_3 DGND /CLK_MINIPCI_EXT /PCI_RESET#_3 DGND /MPCIREQ0#_3 /MPCIGNT0#_3 DGND /PCI_AD(31) /PCI_PME#_3 /PCI_AD(29) Satellite A60/ Pro A60 Maintenance Manual...
  • Page 228 /PCI_AD(16) /PCI_IRDY#_3 DGND /PCI_FRAME#_3 /CLKRUN#_3 /PCI_TRDY#_3 /PCI_SERR#_3 /PCI_STOP#_3 DGND /PCI_PERR#_3 /PCI_DEVSEL#_3 /PCI_CBE#(1) DGND /PCI_AD(14) /PCI_AD(15) DGND /PCI_AD(13) /PCI_AD(12) /PCI_AD(11) /PCI_AD(10) DGND DGND /PCI_AD(9) /PCI_AD(8) /PCI_CBE#(0) /PCI_AD(7) /PCI_AD(6) /PCI_AD(5) /PCI_AD(4) /PCI_AD(2) /PCI_AD(3) /PCI_AD(0) +V5S /PCI_AD(1) DGND DGND Satellite A60 Maintenance Manual...
  • Page 230: Cn502 Mdc I/F Connector (30-Pin

    DGND DGND DGND DGND DGND C.19 CN502 MDC I/F Connector (30-Pin) Table C-19 MDC I/F connector pin assignments (30-Pin) Pin No. Signal Name Pin No. Signal Name /PHONE /A97SYC /A97SDO /A97DI1 /A97RST# /A97DI1 /BITCLK_3_MDC Satellite A60/ Pro A60 Maintenance Manual...
  • Page 232: Cn503 Memory Slot Connector (202-Pin

    /M_CLK_DDR0 +V2.5' /M_CLK_DDR0# DGND DGND DGND /M_DATA_R(16) /M_DATA_R(20) /M_DATA_R(17) /M_DATA_R(21) +V2.5' +V2.5' /M_DQS_R(2) /M_DM_R(2) /M_DATA_R(18) /M_DATA_R(22) DGND DGND /M_DATA_R(19) /M_DATA_R(23) /M_DATA_R(24) /M_DATA_R(28) +V2.5' +V2.5' /M_DATA_R(25) /M_DATA_R(29) /M_DQS_R(3) /M_DM_R(3) DGND DGND /M_DATA_R(26) /M_DATA_R(30) /M_DATA_R(27) /M_DATA_R(31) Satellite A60/ Pro A60 Maintenance Manual...
  • Page 233 /M_A(8) DGND DGND /M_A(7) /M_A(6) /M_A(5) /M_A(4) /M_A(3) /M_A(2) /M_A(1) /M_A(0) +V2.5' +V2.5' /M_A(10) /M_A(14) /M_A(13) /M_RAS_R# /M_WE_R# /M_CAS_R# /M_CS0# /M_CS1# /M_A(15) DGND DGND /M_DATA_R(32) /M_DATA_R(36) /M_DATA_R(33) /M_DATA_R(37) +V2.5' +V2.5' /M_DQS_R(4) /M_DM_R(4) /M_DATA_R(34) /M_DATA_R(38) Satellite A60/ Pro A60 Maintenance Manual...
  • Page 234 +V2.5' /M_DQS_R(6) /M_DM_R(6) /M_DATA_R(50) /M_DATA_R(54) DGND DGND /M_DATA_R(51) /M_DATA_R(55) /M_DATA_R(56) /M_DATA_R(60) +V2.5' +V2.5' /M_DATA_R(57) /M_DATA_R(61) /M_DQS_R(7) /M_DM_R(7) DGND DGND /M_DATA_R(58) /M_DATA_R(62) /M_DATA_R(59) /M_DATA_R(63) +V2.5' +V2.5' /SMBDATA_3 DGND /SMBCLK_3 DGND +V3S' DGND /N$69423 DGND DGND Satellite A60/ Pro A60 Maintenance Manual...
  • Page 236: Cn2000 Touch Pad Connector (12-Pin

    Pin No. Signal Name Pin No. Signal Name +V3A_CN /DCIN_OLED#_CN /DCIN_GLED#_CN /BAT0_OLED#_CN /BAT0_GLED#_CN +V5S_CN +V5S_CN /IDELED#_CN +V3S_CN +V3S_CN /WLON_LED#_CN +V3_CN /PWR_OLED#_CN /PWR_GLED#_CN /IM_CLK_CN /IM_DAT_CN /IR_TX_CN /IR_RX_CN /IR_SD_CN PGND PGND PGND PGND PGND PGND PGND Satellite A60/ Pro A60 Maintenance Manual...
  • Page 238: Jack1 Dc_In Connector (2-Pin

    Signal Name ANAGND AREF ANAGND ANAGND AREF ANAGND ANAGND C.25 JACK3 Headphone Connector (6-Pin) Table C-25 Headphone connector pin assignments (6-Pin) Pin No. Signal Name Pin No. Signal Name ANAGND ANAGND ANAGND ANAGND ANAGND Satellite A60/ Pro A60 Maintenance Manual...
  • Page 240: System Board

    C.21 CN2000 Touch Pad Connector (12-Pin)..............C-1 C.22 CN2002 LED Connector (24-Pin) ................C-1 C.23 JACK1 DC_IN Connector (2-Pin)................C-1 C.24 JACK2 Ext_Microphone Connector (6-Pin) ............C-1 C.25 JACK3 Headphone Connector (6-Pin) ..............C-1 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 241 Keyboard Scan/Character Codes Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Note Keytop Make Break Make Break ‘ ~ 7 & BkSp Satellite A60/ Pro A60 Maintenance Manual...
  • Page 242 Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Note Keytop Make Break Make Break Caps Lock ‘ “ Enter Shift (L) No.102 , < . > Shift (R) Satellite A60/ Pro A60 Maintenance Manual...
  • Page 243 Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Note Keytop Make Break Make Break Ctrl Alt (L) Space ALT (R) ← Home ↑ ↓ PgUp PgDn → Satellite A60/ Pro A60 Maintenance Manual...
  • Page 244 5. * This key corresponds to key No. 42 in a 102-key model. 6. * Refer to Table D-6, No. 124 key scan code. 7. * Refer to Table D-7, No. 126 key scan code. 8. * 205~207 are for JAPAN keyboard only Satellite A60/ Pro A60 Maintenance Manual...
  • Page 245 Shift key, scan codes are changed as listed below: With left Shift With right Shift Set 1 E0 AA __________ E0 B6 E0 2A ___________ E0 36 Set 2 E0 F0 12 ________ E0 F0 59 E0 12 ___________ E0 59 Satellite A60/ Pro A60 Maintenance Manual...
  • Page 246 Make Break Make Break ← Home ↑ ↓ PgUp PgDn → Table D-4 Scan codes with Fn key Code set 1 Code set 2 Keytop Make Break Make Break CTRL LALT ARROW NUMERIC Scrl Satellite A60/ Pro A60 Maintenance Manual...
  • Page 247 Code set 2 Make Break Make Break (–) Table D-6 No.124 key scan code Shift Code set 1 Code set 2 Make Break Make Break Prt Sc Common Ctrl + Shift + Alt + Satellite A60/ Pro A60 Maintenance Manual...
  • Page 248 Table D-7 No.126 key scan code Shift Code set 1 Code set 2 Make Make Pause Common* E1 1D E1 F0 Ctrl* E0 46 7E E0 F0 *: This key generates only make codes. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 249: Appendix E Key Layout

    Apx E Key Layout Appendices Apx. E Key Layout Appendix E Key Layout United States (US) Keyboard Figure E-1 US keyboard JAPAN (JP) Keyboard Figure E-2 JP keyboard Satellite A60/ Pro A60 Maintenance Manual...
  • Page 251 Apx E Key Layout Appendices Spanish (SP) Keyboard Figure E-3 SP keyboard Korean (KR) Keyboard Figure E-4 KR keyboard Satellite A60/ Pro A60 Maintenance Manual...
  • Page 253 Apx E Key Layout Appendices Canadian-French (CF) Keyboard Figure E-5 CF keyboard French (FR) Keyboard Figure E-6 FR keyboard Satellite A60/ Pro A60 Maintenance Manual...
  • Page 255 Apx E Key Layout Appendices German (GR) Keyboard Figure E-7 GR keyboard Italian (IT) Keyboard Figure E-8 IT keyboard Satellite A60/ Pro A60 Maintenance Manual...
  • Page 257 Apx E Key Layout Appendices Taiwan (TC) Keyboard Figure E-9 TC keyboard E.10 Portuguese (PT) Keyboard Figure E-11 PT keyboard Satellite A60/ Pro A60 Maintenance Manual...
  • Page 258 Appendices Apx E Key Layout E.11 DU, UE, US International (USE) Keyboard Figure E-12 USE keyboard E.12 Arabic (AR) Keyboard Figure E-13 AR keyboard Satellite A60/ Pro A60 Maintenance Manual...
  • Page 259 Apx E Key Layout Appendices E.13 Belgian (BE) Keyboard Figure E-14 BE keyboard E.14 Russian (RU) Keyboard Figure E-15 RU keyboard Satellite A60/ Pro A60 Maintenance Manual...
  • Page 260 Appendices Apx E Key Layout E.15 Swiss/Switzerland (SL) Keyboard Figure E-16 SL keyboard E.16 Swedish (SW) Keyboard Figure E-17 SW keyboard Satellite A60/ Pro A60 Maintenance Manual...
  • Page 261 Apx E Key Layout Appendices E.17 Norwegian (NO) Keyboard Figure E-18 NO keyboard E.18 Danish (DK) Keyboard Figure E-19 DK keyboard Satellite A60/ Pro A60 Maintenance Manual...
  • Page 263 Apx E Key Layout Appendices E.19 Turkey (TR) Keyboard Figure E-18 TR keyboard E.20 Greek (GK) Keyboard Figure E-19 GK keyboard Satellite A60/ Pro A60 Maintenance Manual...
  • Page 265 Apx E Key Layout Appendices E.21 Estonia (ES) Keyboard Figure E-19 ES keyboard E.22 Herbrew (HE) Keyboard Figure E-19 HE keyboard Satellite A60/ Pro A60 Maintenance Manual...
  • Page 266 Appendices Apx E Key Layout E.23 Czech (CZ) Keyboard Figure E-18 CZ keyboard E.24 Lithuanian (LI) Keyboard Figure E-18 LI keyboard Satellite A60/ Pro A60 Maintenance Manual...
  • Page 267 Apx E Key Layout Appendices E.25 Hungary (HU) Keyboard Figure E-18 HU keyboard E.26 Slovakia (SA) Keyboard Figure E-18 SA keyboard Satellite A60/ Pro A60 Maintenance Manual...
  • Page 268 Appendices Apx E Key Layout E.27 Yugoslavia (YU) Keyboard Figure E-19 YU keyboard Satellite A60/ Pro A60 Maintenance Manual...
  • Page 269: Appendix F Bios Rewrite Procedures

    ] key (on the left of the space key). (Keep holding down the key until a message appears on the screen.) The BIOS rewriting starts. 6. When the process is completed, eject the BIOS/EC/KBC rewriting disk and the system is automatically reset. Satellite A60/ Pro A60 Maintenance Manual...
  • Page 270 (maximum), depending on the conditions of the computer or ICs. The computer is not hung up. Allow sufficient time. Never reboot or turn off the power to the computer before the rewriting is completed. Satellite A60/ Pro A60 Maintenance Manual...

This manual is also suitable for:

Satellite pro a60

Table of Contents