Page 1 ® Satellite A60/A65 Series User’s Guide If you need assistance: ❖ Toshiba Global Support Centre Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see page 165 in this guide. Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.
Page 2 AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE. YOU AGREE THAT TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS, PROFITS, PROGRAMS, DATA OR...
Page 3 Only Peripherals complying with the FCC Class B limits may be attached to this equipment. Operation with noncompliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's parallel port, monitor port, USB port, PS/2 port port and microphone jack.
Page 4: Industry Canada Requirement
Contact: Toshiba America Information Systems, Inc. 9740 Irvine Blvd. Irvine, CA 92618-1697 (949) 583-3000 Industry Canada requirement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conformé à la norme NMB-003 du Canada.
Page 5: Telephone Company Procedures
If trouble is experienced with this equipment, for repair or limited warranty information, please contact Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Toshiba, or the Toshiba Support Centre within the United States at (800) 457-7777 or Outside the United States at (949) 859-4273.
Page 6 Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. Instructions for IC CS-03 Certified Equipment NOTICE: The Industry Canada label identifies certified equipment.
Page 7: Wireless Interoperability
USOC RJ11C. Wireless Interoperability The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ❖...
Page 8: Wireless Lan And Your Health
Wireless LAN device prior to turning on the equipment. Regulatory Information The TOSHIBA Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards.
Page 9 ETS 300 328 Technical requirements for radio equipment ETS 300 826 General EMC requirements for radio equipment. English: Hereby, TOSHIBA Corp. Digital Media Network Company, declares that this Radio LAN device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Page 10 Radio LAN device in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Bij deze TOSHIBA Corp. Digital Media Network Company dat deze Radio LAN device voldoet aan de essentiële eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC.
Page 11 Caution: Exposure to Radio Frequency Radiation The radiated output power of the TOSHIBA Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits. Nevertheless, the TOSHIBA Wireless LAN Mini PCI Card shall be used in such a manner that the potential for human contact during normal operation is minimized.
Page 12 Caution: Radio Frequency Interference Requirements This device is restricted to indoor use due to its operation in the 5.15 GHz to 5.25 GHz frequency range. FCC requires this product to be used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems.
Page 13: Device Authorization
The interference range of this equipment is less than 40m. 2,400 MHz to 2,483.5 MHz. It is possible to avoid the band of mobile object identification systems. 3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-13-1100...
Page 14: Radio Approvals For Wireless Devices
Approval Number: D01-1128JP TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018, 03GZDA0017 The following restrictions apply: ❖ Do not disassemble or modify the device. ❖ Do not install the embedded wireless module into other device. ❖ 5.17 GHz to 5.23 GHz for indoor use only Radio approvals for wireless devices NOTE The following information is dependent on what type of wireless device is in...
Page 15 Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries België/ For private usage outside buildings across public grounds over less than Belgique: 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m.
Page 16 802.11a (5 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Turbo Mode (5 GHz) Canada Europe - Restrictions for use of 5 GHz Frequencies in European Community Countries European Community Countries Austria Belgium, France, Switzerland/Lichtenstein Denmark, Finland, Germany, Greece, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Sweden, UK...
Page 17 ❖ This device must not be operated in ad-hoc mode using channels in the 5 GHz bands in the European Community. Ad-hoc mode provides a direct communication between two client devices without a Wireless LAN Access Point. ❖ This device must be used with Access Points that have employed and activated a radar detection feature required for European Community operation in the 5 GHz bands.
Page 18 802.11a (5 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Turbo Mode (5 GHz) Canada Approved Countries/Regions for use for the Intel Wireless LAN 2100 3B Mini PCI Adapter This equipment is approved to the radio standard by the countries/regions in the following table.
Page 19: Bluetooth Wireless Technology Interoperability
New Zealand Portugal Sweden Bluetooth wireless technology Interoperability Bluetooth™ Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ❖...
Page 20: Bluetooth Wireless Technology And Your Health
Always use Bluetooth™ cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or http://www.pcsupport.global.toshiba.com in the United States for...
Page 21: Regulatory Statements
community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of Bluetooth wireless technology may be restricted by the proprietor of the building or responsible representatives of the organization.
Page 22 The radiated output power of the Bluetooth™ Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth™ Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized.
Page 23 Article 17 Any use of low power radio frequency electric machinery shall not affect the aviation safety and interfere with legal communications. In event that any interference is found, the use of such electric machinery shall be stopped immediately, and reusing of such products can be resumed until no interference occurs after improvement.
Page 24 This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems. 3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-13-1100 Direct Dial: 03-3457-5916...
Page 25 Copyright This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.
Page 26 ConfigFree is a trademark of Toshiba Corporation. Wi-Fi is a registered trademark of the Wireless Capability Ethernet Alliance. Dolby - Manufactured by Toshiba under license from Dolby Laboratories/ Dolby and the double-D symbol are trademarks of Dolby Laboratories. TouchPad is a trademark of Synaptics, Inc.
Page 27 Computer disposal information This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government or the Electronic Industries Alliance at www.eiae.org.
Page 28: Table Of Contents
Important information on your computer’s Setting up your computer ... 46 Setting up your software... 46 Registering your computer with Toshiba ... 47 Adding external devices ... 47 Connecting to a power source ... 48 Charging the main battery... 51...
Page 29 Your computer’s features and specifications... 53 Turning on the power... 53 Activating the power-on password... 54 Using the TouchPad™ ... 55 Using TOSHIBA Touch and Launch... 58 Installing additional memory (optional) ... 62 Removing a memory module... 66 Using an external keyboard... 68 Connecting a mouse ...
Page 30 Contents Windows Overlay keys... 83 Starting a program... 84 Starting a program from the Start menu... 85 Starting a program from Windows Starting a program from the Run dialog box ... 86 Saving your work ... 88 Printing your work ... 90 Backing up your files ...
Page 31 Going into Standby mode more quickly ... 113 Starting again from Standby ... 115 Toshiba’s online resources... 115 Chapter 3: Mobile Computing ... 116 Toshiba’s energy-saver design ... 116 Running the computer on battery power ... 116 Battery Notice ... 117 Power management ... 117 Using additional batteries ...
Page 32 Using PC Cards... 148 Inserting PC Cards ... 148 Removing PC Cards ... 149 Hot swapping... 150 Chapter 5: Toshiba Utilities ... 151 TOSHIBA Accessibility ... 152 Fn-esse ... 153 Starting Fn-esse... 153 Assigning a key to a program or document ... 154 Viewing existing key assignments ...
Page 33 TOSHIBA Console ... 157 Customize Your Computer ... 159 Security... 159 Power Management ... 159 Toshiba Hardware Setup ... 161 TOSHIBA Zooming Utility... 163 Application Launch Button ... 164 Chapter 6: If Something Goes Wrong ... 165 Problems that are easy to fix ... 165 Problems when you turn on the computer...
Page 34 Contents Contacting Toshiba ... 194 Other Toshiba Internet Web sites ... 195 Toshiba’s worldwide offices ... 195 Appendix A: Hot Keys ... 197 Volume Mute... 197 Instant password security... 197 Without a password ... 197 With a password ... 198 Maintaining security when the battery is not fully Power usage mode ...
Page 35: Introduction
XP Pro operating system. Your operating system offers exciting features and easy Internet access. This guide contains information about your operating system and how it functions with your Toshiba computer. For specific information on the software, see the Microsoft booklet that shipped with your computer.
Page 36: This Guide
Toshiba's Web site at pcsupport.toshiba.com. While Toshiba has made every effort at the time of publication to ensure the accuracy of the information provided herein, product specifications, configurations, prices, system/ component/options availability are all subject to change without notice.
Page 37: Other Icons Used
the seriousness of the risk, and the icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Page 38: Other Documentation
Toshiba Web site at pcsupport.toshiba.com. If you have a problem or need to contact Toshiba, see Something Goes Wrong” on page ®...
Page 39: Chapter 1: Getting Started
Chapter 1 Getting Started This chapter provides tips for working comfortably, describes how to connect components, and explains what to do the first time you use your notebook computer. Selecting a place to work Your computer is designed to be used in a variety of locations and situations.
Page 40: Keeping Yourself Comfortable
Getting Started Selecting a place to work ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones. ❖ Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters.
Page 41 Placement of the computer Proper placement of the computer and external devices is important to avoid stress-related injuries. ❖ Place the computer on a flat surface at a comfortable height and distance. You should be able to type without twisting your torso or neck, and look at the screen without slouching.
Page 42 Getting Started Selecting a place to work Whichever type you choose, use the following guidelines to adjust your chair for maximum computing comfort. ❖ Position your chair so that the keyboard is at or slightly below the level of your elbow. You should be able to type comfortably with your shoulders relaxed and your forearms parallel to the floor.
Page 43: Work Habits
Your LCD display has a brightness approaching that of a TV device. We recommend that you adjust the brightness of your LCD to a comfortable level to prevent possible strain on your eyes. Arms and wrists ❖ Avoid bending, arching, or twisting your wrists. Keep them in a relaxed, neutral position while typing.
Page 44: Other Precautions
Getting Started Selecting a place to work Other precautions Your notebook computer is designed to provide optimum safety and ease of use, and to withstand the rigors of travel. You should observe certain precautions to further reduce the risk of personal injury or damage to the computer. ❖...
Page 45: Important Information On Your Computer's Cooling Fan
Turning off the computer while it is reading from or writing to a disk may damage the disk, the drive, or both. ❖ Keep the computer and disks away from objects that generate strong magnetic fields, such as large stereo speakers.
Page 46: Setting Up Your Computer
Getting Started Setting up your computer Setting up your computer TECHNICAL NOTE: You must complete all set up steps up to “Setting up your software” before adding external or internal components to your computer. These components include, but are not limited to, a mouse, keyboard, printer, memory, and PC cards.
Page 47: Registering Your Computer With Toshiba
Internet via a voice-grade telephone line or a Local-Area- Network (LAN). NOTE If you chose not to register now, you may register with Toshiba by clicking the Register with Toshiba icon on the desktop. A window displays the message, “Thank you.”...
Page 48: Connecting To A Power Source
Getting Started Connecting to a power source ❖ Connect a mouse (see ❖ Connect a local printer (see page ❖ Install PC Cards (see ❖ Connect an external keyboard (see keyboard” on page ❖ Connect another display device (see display devices” on page ❖...
Page 49 Use only the AC adapter supplied with your computer or an equivalent adapter that is compatible. Use of any incompatible adapter could damage your computer. Toshiba assumes no liability for any damage caused by use of an incompatible adapter.
Page 50 Getting Started Connecting to a power source Plug the AC adapter into the DC-IN. Sample connecting the AC adapter to the computer Connect the power cable to a live electrical outlet. The AC power indicator glows when the computer is connected to an external power source.
Page 51: Charging The Main Battery
Charging the main battery Before you can use the battery to power the computer, you must charge it. Connect the computer to a live power outlet using the AC adapter and power cable. The AC power light glows green and the battery light glows amber to show that it is charging.
Page 52: Using The Computer For The First Time
Getting Started Using the computer for the first time Using the computer for the first time The computer is now ready for you to turn it on and begin using it. Opening the display panel Slide the display latch to the right. Lift the display panel.
Page 53: Your Computer's Features And Specifications
Over a period of time, and depending on the usage of the NOTE computer, the brightness of the LCD Screen will deteriorate. This is an intrinsic characteristic of LCD technology. Screen will dim when the computer is operated on battery power and you may not be able to increase the brightness of the screen.
Page 54: Activating The Power-On Password
When you first turn on your computer, no password is required. But you can set up your computer so that a password is required to complete the powering up process in the future. To activate the power-on password: Double-click the TOSHIBA Console icon on the desktop.
Page 55: Using The Touchpad
NOTE If you forget your power-on password and therefore cannot turn on your computer, take your computer to a Toshiba authorized service center for help. After the third incorrect password submission, the system automatically shuts down.
Page 56 Getting Started Using the TouchPad™ ❖ To move the cursor to the right side of the page, slide your finger across the TouchPad from left to right. ❖ To move it to the left side, slide your finger from right to left.
Page 57 Click the Mouse icon. Click the TouchPAD ON/OFF tab. The TouchPAD ON/OFF tab view window appears. Sample Mouse Properties window Select Disable or Enable, whichever is appropriate. Click Apply. Click OK. The Mouse Properties window closes. Close the Printers and Other Hardware window. Close the Control Panel window.
Page 58: Using Toshiba Touch And Launch
A blue circle within the TOSHIBA Touch and Launch window represents your finger location on the TouchPad. As you move the blue circle over an icon in the TOSHIBA Touch and Launch window, the icon is highlighted or selected. Release your finger from a selected icon to choose the icon's function.
Page 59 To close the TOSHIBA Touch and Launch window, release your finger when the blue circle is not on any icon. Or, highlight the Close icon in the upper right of the TOSHIBA Touch and Launch window. The TOSHIBA Touch and Launch window has the following...
Page 60 TOSHIBA Touch and Launch is controlled/adjusted via an icon on the system tray. The icon changes color when the TOSHIBA Touch and Launch is active. Double-click the icon to open the TOSHIBA Touch and Launch Settings window. Right-click the icon to see the following shortcut menu: ❖...
Page 61 The Option button allows you to define how folders will open, define visual affects and control when to show help. A list of tables appears in the Table section of the TOSHIBA Touch and Launch Settings window. These are the same items (icons) you can choose in the Corner Assignment section of the TOSHIBA Touch and Launch Settings.
Page 62: Installing Additional Memory (Optional)
Additional memory comes in various capacities (visit the Toshiba Web site at information). Your system has one memory slot available for user upgrades. If you use the computer for a long time, the memory module will become hot.
Page 63 Installing additional memory (optional) Do not try to install a memory module under the following conditions. You can damage the computer and the module. 1. The computer is turned on. 2. The computer was shut down using Standby or Hibernation mode.
Page 64 Getting Started Installing additional memory (optional) Sample using a Phillips-head screwdriver to remove the memory cover Remove the screw that holds the memory cover in place, and remove the memory cover. Remove the new memory module from its antistatic packaging. Static electricity can damage the memory module.
Page 65 Installing additional memory (optional) Sample inserting the memory module Avoid touching the connectors on the memory module or on the computer. Grease or dust on the connectors may cause memory access problems. The clips on either side of the module will click to secure the module.
Page 66: Removing A Memory Module
Getting Started Installing additional memory (optional) Removing a memory module If you use the computer for a long time, the memory module will become hot. If this happens, let the module cool to room temperature before you replace it. Do not try to remove a memory module with the computer turned on.
Page 67 Installing additional memory (optional) Pull the clips away from the memory module. The memory module pops partially out of the slot. Sample removing the memory module Carefully remove the module from the slot. Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up.
Page 68: Using An External Keyboard
Getting Started Using an external keyboard Checking total memory When you add or remove memory, you can check that the computer has recognized the change. To do this: Click Start, Control Panel Click Performance and Maintenance. Click System. The General tab view automatically appears and shows the recognized memory.
Page 69: Connecting A Printer
Connecting a printer You can connect a USB-compatible printer to your computer through the USB ports. You can connect a USB printer after you turn on the computer. Alternatively, you can connect a parallel printer to the computer’s parallel port. Connecting a USB printer To achieve the connection, you need a suitable USB cable, which may come with your printer.
Page 70 Getting Started Connecting a printer If your printer has not been detected automatically when connected to the computer, you must install the printer driver for the model of printer that is connected to your computer. You install the printer driver either by following the instructions indicated in your printer guide, or by using the operating system’s Add Printer Wizard.
Page 71 The Printers and Faxes window appears. Sample Printers and Faxes window Click Add a printer. The Add Printer Wizard window appears. Sample Add Printer Wizard Getting Started Connecting a printer...
Page 72: Connecting An Optional External Diskette Drive
Getting Started Connecting an optional external diskette drive Follow the on-screen instructions. HINT: If you are using more than one printer, make sure the name is descriptive enough to help you tell the difference. Connecting an optional external diskette drive You can attach an optional external USB diskette drive to use diskettes with your computer.
Page 73: Using External Display Devices
Using external display devices Your computer comes with a built-in LCD display, but you can easily attach an external monitor to your computer if you need a larger screen. Once you have connected an external display device, you can choose to use the internal display only, the external device only, or both simultaneously.
Page 74: Adjusting The Quality Of The External Display
Getting Started Using external display devices ❖ External device only ❖ Built-in display and TV (or other external video device) simultaneously ❖ TV (or other external video device) only Release the TECHNICAL NOTE: You can also change these settings using the Display Properties box in the Control Panel.
Page 75: Powering Off The Computer
enabled and the Display area (resolution) set to 640 x 480 or 800 x 600, the image on the internal display panel may appear stretched. NOTE The Windows display resolutions below 800 x 600. To display the 640 x 480 resolution, you may need to click the Settings tab in the Display Properties window, click Advanced, click the Adapter tab, click List all modes, and select 640 x 480.
Page 76: Caring For Your Computer
Cleaning the computer To keep your computer clean, gently wipe the display panel and exterior case with a lightly dampened cloth. Ask your Toshiba dealer for suggestions for appropriate cleaning products. Keep liquid, including cleaning fluid, out of the computer’s keyboard, speaker grille, and other openings.
Page 77: Moving The Computer
Although your notebook computer is built to withstand reasonable shock and vibration, transport it in a carrying case for long trips. You can purchase a carrying case from your Toshiba dealer or the Toshiba Web site at accessories.toshiba.com. Using a computer lock You may want to secure your computer to a heavy object such as your desk.
Page 78 Getting Started Caring for your computer Insert the cable’s locking end into the security lock slot, then rotate the key a quarter-turn and remove it. Sample locking the computer The computer is now securely locked to deter computer theft.
Page 79: Chapter 2: Learning The Basics
Chapter 2 Learning the Basics This chapter lists some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work temporarily stays in the computer’s memory until you save it to the disk. You will lose all unsaved work, if, for example, a system error occurs and you must restart your computer, or your battery runs out of charge while you are working.
Page 80 Learning the Basics Computing tips ❖ Back up your files to storage media on a regular basis. Label the backup copies clearly and store them in a safe place. If your hard disk suddenly fails, you may lose all the data on it unless you have a separate backup copy.
Page 81: Using The Keyboard
Using the keyboard Sample keyboard Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖ The spacebar creates a space character instead of just passing over an area of the page. ❖ The lowercase l (el) and the number 1 are not interchangeable.
Page 82: Ctrl, Fn, And Alt Keys
Learning the Basics Using the keyboard Ctrl, Fn, and Alt keys Ctrl Sample Ctrl, Fn and Alt keys , and Ctrl program you are using. For more information, see your program documentation. Function keys The function keys (not to be confused with the 12 keys at the top of the keyboard.
Page 83: Overlay Keys
Overlay keys Caps Lock Shift Ctrl Sample keyboard overlay keys The keys with numbers and symbols on the front of them form the numeric and cursor overlay. This overlay lets you enter numeric data or control the cursor as you would using the ten-key keypad on a desktop computer’s keyboard.
Page 84: Starting A Program
Learning the Basics Starting a program To use the cursor control overlay when the numeric overlay is on, press and hold down keys. To return to the numeric overlay, release To turn off the numeric keypad overlay, hold down the and press indicator panel goes out.
Page 85: Starting A Program From The Start Menu
❖ Use Windows Explorer to locate the program file ❖ Use the Run dialog box Starting a program from the Start menu When you install a program, the operating system usually puts an icon in the All Programs menu. To start a program that has an icon in the All Programs menu, follow these steps, which use the Windows Click Start, then point to All Programs.
Page 86: Starting A Program From The Run Dialog Box
Learning the Basics Starting a program Click Accessories. Click Windows Explorer. Click My Computer to expand the window. In the left part of the window, under the C: icon, double- click the folder containing the program, in this case Program Files. Windows folder on the right side of the window.
Page 87 Sample Run dialog box In the Run dialog box: ❖ If you know the program’s location, type the command line. For a program in the Windows program name. Otherwise, type the full file path. For example, to access WordPad, type: c:\Program Files\WindowsNT\Accessories\Wordpad, ❖...
Page 88: Saving Your Work
Learning the Basics Saving your work Saving your work Before you turn off the computer, save your work to the hard disk drive. Always save your data even when you are using the Stand by. If your battery fully discharges, your information will be lost. Your computer can be configured to warn you when the battery is running low, see Saving files...
Page 89: File Names
Type a file name, then click Save. HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name. ® The Windows XP operating system supports file names of up to 255 characters;...
Page 90: Printing Your Work
Learning the Basics Printing your work To save: ❖ A file you are updating, open the program’s File menu and click Save. ❖ A new file, choose Save As from the File menu, type a name for the file, and click OK. HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name.
Page 91: Backing Up Your Files
Backing up your files Backing up your files means copying individual files to media, such as a CD. Or copying entire sections of your hard disk to another device such as a tape drive or to your network partition. To back up to a CD, optional diskette drive, or other media: Insert the media into the appropriate drive.
Page 92: Using The Dvd-Rom Or Multi-Function Drive
Learning the Basics Using the DVD-ROM or multi-function drive TECHNICAL NOTE: When restoring files, the backup program prompts you if you try to overwrite a file that already exists on the hard disk. Make sure the backup version is the one you want before overwriting the existing file.
Page 93: Dvd-Rom Or Multi-Function Drive Components
Using the DVD-ROM or multi-function drive DVD-ROM or multi-function drive components Your DVD-ROM or multi-function drive may look like this: Eject button Manual eject hole Sample DVD-ROM or multi-function drive Never press the eject button or turn off the computer while the drive-in-use indicator light is glowing.
Page 94: Inserting A Disc
Learning the Basics Using the DVD-ROM or multi-function drive The previous track button returns to the preceding track on the disc. The next track button skips to the following track on the disc. The play/pause button starts playing the disc or makes it pause if currently playing.
Page 95 Using the DVD-ROM or multi-function drive Hold the disc by its edges and check that it is clean and free of dust. Handle discs carefully. Avoid touching the surface of the disc. Grasp it by its center hole and edge. If you handle the disc incorrectly, you could lose data.
Page 96: Playing An Audio Cd
Learning the Basics Using the DVD-ROM or multi-function drive Spindle Disc Sample positioning the disc on the spindle Make sure the disc is properly positioned on the spindle. If you position the disc incorrectly, it can jam the disc tray. Close the disc tray by pressing gently on the center of the tray until it clicks indicating that it is locked.
Page 97 Learning the Basics Using the DVD-ROM or multi-function drive Sample Audio CD window ® The Windows Media Player window appears.
Page 98: Playing Cds Using Auto-Run
Learning the Basics Using the DVD-ROM or multi-function drive Rewind Play Stop Previous track Next track Sample Windows Media The Windows Media an ordinary compact disc player: ❖ To play the CD or to pause, click the Play/Pause button on the CD Player control panel. ❖...
Page 99: Creating A Cd
Using the DVD-ROM or multi-function drive Open the Start menu and select My Computer. Click the DVD-ROM/multi-function drive icon. The disk drive will run the CD. If your disk does not run using this method, try using an application that is associated with the media on the disk. For example, if it is a music CD, open Windows and point it to play the CD.
Page 100: Removing A Disc With The Computer On
Learning the Basics Using the DVD-ROM or multi-function drive Removing a disc with the computer on Never press the eject button or turn off the computer while the drive-in-use light is glowing. Doing so could damage the disk or the drive. Locate and press the eject button.
Page 101: Caring For Cd And Dvd Discs
Caring for CD and DVD discs ❖ Store your discs in their original containers to protect them from scratches and keep them clean. ❖ Never bend a disc or place heavy objects on top of it. ❖ Hold a disc by its outside edge. Fingerprints on the surface of a compact disc can prevent the drive from reading the data properly.
Page 102: Turn Off Or Shut Down Command
Learning the Basics Powering down the computer Each option has its advantages. TECHNICAL NOTES: Before using any of these options to power down your computer, save your files and make sure the disk activity lights are off. If you change your mind and decide to continue working after all, wait a few seconds before turning the computer on again.
Page 103: Restart Command
Restart command Restart is the same as Turn Off or Shut down but automatically powers up the computer. Use it when you need to reload the operating system, for example to activate changes to system settings. Hibernation command The Hibernation command shuts the computer down completely, but it first saves the current state of the computer to the hard disk.
Page 104: Standby Command
Learning the Basics Powering down the computer Standby command Standby puts the computer into a power-saving mode. Standby holds the current state of the computer in memory so that, when you restart the computer, you can continue working from where you left off. Factors when choosing Standby: ❖...
Page 105: Using Turn Off Or Shut Down
Using Turn Off or Shut down If you are using the Windows or are using the Windows and are not a member of a domain, power off the computer as follows: Click Start, Turn off computer. The Turn off computer window appears. Sample Turn off computer window Click Turn Off.
Page 106: Turning Off Or Shutting Down More Quickly
In addition to the method described above, you can turn off or shut down the computer by pressing the power button. To do so, you must preset the mode in Toshiba’s Power Saver utility. Open the Start menu, click Control Panel, then Performance and Maintenance.
Page 107 Sample TOSHIBA Power Saver Properties window Select Shut down for the options you want. ❖ When I press the power button Set this option to Shut down to have the computer shut down when you press the power button. ❖...
Page 108: Starting Again After Turn Off Or Shut Down
Learning the Basics Using Hibernation Starting again after Turn Off or Shut down To start the computer up again, press and release the power button. The on/off light turns on. Using Hibernation When Hibernation is enabled, you can put the computer into Hibernation in more than one way.
Page 109 Sample Turn off computer window with shift key held down to show Hibernate option Hold down the (“Hibernate” only appears when the The computer saves the state of the system, including all open programs and files, to the hard disk. Then the computer turns itself off.
Page 110: Going Into Hibernation Mode More Quickly
Open the Start menu, click Control Panel, then Performance and Maintenance. Click the Toshiba Power Saver icon. Click the Setup Action tab. The TOSHIBA Power Saver Properties window appears. Fn + F4. 201.
Page 111 Sample TOSHIBA Power Saver Properties window Select Hibernation for the options you want. ❖ When I press the power button Set this option to Hibernate so that the computer will go into Hibernation mode when you press the power button.
Page 112: Starting Again From Hibernation Mode
Learning the Basics Using Standby Starting again from Hibernation mode To start the computer from Hibernation mode, press and release the power button. The computer returns to the screen you were using. If you put the computer in Hibernation mode by closing the display panel, you can start it again by opening the display panel.
Page 113: Going Into Standby Mode More Quickly
mode. The on/off light ( machine is in Standby mode. If you are using the Windows system and are a member of a domain, power off the computer using the Standby command as follows: Click Start, then Shut down. The Shut Down window appears. Sample Stand by window Select Stand by from the drop-down list of options.
Page 114 Open the Start menu, click Control Panel then Performance and Maintenance. Click the Toshiba Power Saver icon. Click the Setup Action tab. The TOSHIBA Power Saver Properties window appears. Sample TOSHIBA Power Saver Properties window Select Standby for the options you want. ❖...
Page 115: Starting Again From Standby
Toshiba’s online resources Toshiba maintains a number of online sites to which you can connect. These sites provide information about Toshiba products, give help with technical questions, and keep you up to date with future upgrades.
Page 116: Chapter 3: Mobile Computing
Many of these energy-saving features have been set by Toshiba. We recommend you leave these features active, allowing your computer to operate at its maximum energy efficiency, so that you can use it for longer periods while traveling.
Page 117: Battery Notice
Toshiba Web site at accessories.toshiba.com. To ensure that the battery maintains its maximum capacity, operate the computer on battery power at least once a month until the battery is fully discharged.
Page 118: Using Additional Batteries
Users who are not completely familiar with the power management component of the system should use the preset configuration. For assistance with setup changes, contact the Toshiba Global Support Centre. Using additional batteries If you spend a lot of time traveling and need to work for many hours without an AC power source, you may want to carry additional charged batteries with you.
Page 119: Charging The Main Battery
Doing so may reduce the potential charge of the battery. Use only battery chargers designed to work with your notebook computer. You can order a Toshiba battery charger from Toshiba’s Web site at accessories.toshiba.com. Charging the main battery To charge the battery, plug the computer into a live wall outlet.
Page 120: Charging The Rtc Battery
Mobile Computing Charging the batteries Leave the power connected, and the battery should begin charging after a few minutes. HINT: Once the battery is fully charged, we recommend that you operate your computer on battery power until the battery discharges completely. Doing this extends battery life and helps ensure accurate monitoring of battery capacity.
Page 121: Monitoring Battery Power
It is seldom necessary to charge the RTC battery because NOTE it charges while the computer is on. If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date or stop working. When Hibernation mode is enabled and the RTC battery is completely discharged, a warning prompts you to reset the real-time clock.
Page 122 Open the Start menu, click Control Panel then Performance and Maintenance. Click the Toshiba Power Saver icon. The Toshiba Power Saver Properties window appears. Sample Toshiba Power Saver Properties window The remaining battery charge is indicated on the top left side of the dialog box.
Page 123: Conserving Battery Power
Toshiba has combined these options into preset power profiles. Using one of these profiles lets you choose between maximum power savings and peak system performance. You may also set individual power-saving options to suit your own needs.
Page 124: What To Do When The Battery Runs Low
To change the default alarm settings: Open the Start menu, click Control Panel then Performance and Maintenance. Click the Toshiba Power Saver icon. Click the Setup Action tab. Select the Alarm settings in the Setup Alarm section. ®...
Page 125: Changing The Main Battery
Changing the main battery When your battery power is running low, you have two options—connect the computer to an AC power source or install a charged battery. When handling a battery, be careful not to drop it or short- circuit its terminals. Also, do not drop, hit or otherwise impact the battery.
Page 126 Mobile Computing Changing the main battery If the battery lock latches are in the locked position (toward the left of the computer), slide them towards the right of the computer. Sample releasing the battery lock Slide the battery release latch to release the battery. Sample releasing the battery...
Page 127: Inserting The Battery In The Computer
While still holding the release latch in the open position, lift the battery pack out of the computer. Sample removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately following the advice in Inserting the battery in the computer Assuming you just removed the battery pack (see...
Page 128: Taking Care Of Your Battery
If a battery is leaking or damaged, replace it immediately. Use protective gloves when handling a damaged battery. ❖ To replace the main battery, use an identical battery that you can purchase through to Toshiba Web site at accessories.toshiba.com. ❖ A reverse polarity condition should be avoided with all batteries.
Page 129: Maximizing Battery Life
❖ Do not expose the battery pack to fire. The battery pack could explode. Maximizing battery life To maximize the life of your battery pack: ❖ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges.
Page 130: Disposing Of Used Batteries Safely
Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by Toshiba. After repeated use, the batteries will finally lose their ability to hold a charge and you will need to replace them. Under federal, state and local laws, it may be illegal to dispose of old batteries by placing them in the trash.
Page 131: Traveling Tips
❖ Always travel with the computer in a carrying case. Toshiba offers a choice of carrying cases for the computer. They all provide plenty of extra space for manuals, power cables, and compact discs. Contact your authorized Toshiba representative for more information.
Page 132: Chapter 4: Exploring Your Options
Chapter 4 Exploring Your Options In this chapter, you will explore some of the special features of your Satellite Exploring the desktop The desktop is the launching pad for everything you can do in the Windows system. You use its features to start programs, find documents, set up system components, and perform most other computing tasks.
Page 133: Finding Your Way Around The Desktop
Exploring Your Options Exploring the desktop Finding your way around the desktop Your computer’s desktop includes several standard features: icons, Start button, taskbar, system tray, and background pattern. Icons Taskbar Start button System tray ® Sample Windows XP operating system desktop Icons An icon represents a folder, file, or program that can be quickly activated by double-clicking the icon.
Page 134 Exploring Your Options Exploring the desktop Recycle Bin — Holds files you have deleted. You may be able to retrieve these files until you empty the Recycle Bin. TECHNICAL NOTE: If you delete a file from a diskette, it does not go into the Recycle Bin.
Page 135: System Tray
Taskbar Each time you open a program, a button associated with that program appears on the taskbar. With some programs, a button appears on the taskbar for each document or window you open. You can use these buttons to quickly switch between the programs or windows.
Page 136: Setting Up For Communications
To stay current on the most recent software and hardware NOTE options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at accessories.toshiba.com. Determining the COM port Your modem is connected to one of the computer’s COM (communications) ports.
Page 137 The following procedure is intended to support you if you need to either upgrade your modem or reset the port to the default settings. If you are having trouble connecting through the modem, you may need to determine the current COM port name and possibly change it.
Page 138: Connecting The Modem To A Telephone Line
Now you are ready to send a fax or use the modem to connect to an online service or the Internet. For more detailed information regarding your computer’s modem, visit Toshiba’s Web site at accessories.toshiba.com. Connecting your computer to a network You can connect your computer to a network to increase its capabilities and functionality using one of its communication ports.
Page 139 Setting up the connection To set up an office connection, consult your network administrator for network settings and additional considerations. To use a dial-up connection, have your network administrator configure your computer for the network and supply you with the telephone number for the dial-up connection. To set up the network connection, use the Dial-Up Networking Wizard: Click Start and point to All Programs.
Page 140: An Overview Of Using The Internet
Your computer may have an integrated Wi-Fi Wireless LAN Mini PCI module. It is recommended that you do not remove the module from your computer. For assistance, contact a Toshiba Wireless Authorized Service Partner. For systems equipped with Wi-Fi, flip the wireless on/off switch to the On position.
Page 141: The World Wide Web
The World Wide Web The World Wide Web (or “Web”) is a subset of the Internet— a collection of interlinked documents (located on computers connected to the Internet) that work together using a specific Internet protocol called Hypertext Transfer Protocol (HTTP). The World Wide Web offers information as text, images, audio, or video to be referenced from anywhere in the world.
Page 142: Surfing The Internet
Exploring Your Options An overview of using the Internet Once you have established an ISP account, you can connect to the Internet. Connect your computer’s modem to a telephone line. For more information on connecting a modem, see the modem to a telephone line” on page Start your Web browser.
Page 143: Internet Features
Internet features The Internet offers many types of communication tools to help you perform many tasks. ❖ Internet email To send and receive your own email, you need a mailbox on the Web or an email address. If you have an account with an ISP, you can probably set up an email address at the same time you sign up for the service.
Page 144: Exploring Video Features
Exploring Your Options Exploring video features Exploring video features Your computer’s video features enable you to view ® Windows presentations or DVD movies on the computer screen (display panel or external monitor). For information on connecting an external monitor, see “Using external display devices”...
Page 145: Playing Dvds
The Monitor Settings window appears and asks if you want to keep the settings. Click Yes. To change the settings back, repeat steps Playing DVDs Your computer must be on for you to use the DVD-ROM or multi-function drive. Open the DVD-ROM or multi-function drive tray. Place the DVD in the DVD-ROM or multi-function drive.
Page 146: Recording Sounds
Exploring Your Options Exploring audio features Recording sounds You can make audio recordings and save them as .wav files by connecting an external microphone or other sound source to the microphone jack and using the Sound Recorder feature in the operating system. DEFINITION: A .wav (pronounced “wave”) file is a format for storing sound in files.
Page 147: Adjusting Recording Settings
Click the Record button and speak normally into the microphone. You can only record 60 seconds at a time. NOTE When you have finished recording, click the Stop button. To hear what you just recorded, click the Play button. To save the file, select Save from the File menu. Adjusting recording settings The better the quality of the recording, the more disk space the sound file requires.
Page 148: Using Pc Cards
Exploring Your Options Using PC Cards TECHNICAL NOTE: Use amplified speakers that require an external power source. Other types of speakers will be inadequate to produce sound from the computer. To play back sound files through external speakers or headphones: Locate the headphone jack.
Page 149: Removing Pc Cards
To insert a PC Card: Turn off the computer. You may also hot swap a PC Card (see page 150). Align the card connectors with the PC Card slot and carefully slide the card into the slot until it locks into place.
Page 150: Hot Swapping
Exploring Your Options Using PC Cards Sample removing a PC Card Remove the PC Card and store it properly. Hot swapping One of the great things about PC Cards is that you can replace one PC Card with another while the computer is on. This is called “hot swapping.”...
Page 151: Chapter 5: Toshiba Utilities
Together, these allow you to ascertain certain system details, set additional options, or change default options. These utilities are described in this chapter: ❖ TOSHIBA Accessibility ❖ Fn-esse ❖ Hotkey utility ❖ TOSHIBA Console ❖ TOSHIBA Zooming Utility ❖ Application Launch Button...
Page 152: Toshiba Accessibility
Toshiba Utilities TOSHIBA Accessibility TOSHIBA Accessibility The TOSHIBA Accessibility utility allows you to use the Fn key to create a hot key combination with one of the function keys without pressing the two keys simultaneously as is usually required. Using Accessibility enables you to make the Fn key a sticky key, meaning you can press it once, release it and then press a function key to activate the hot key function.
Page 153: Fn-Esse
You can assign any key that is not associated with a hot key or a keyboard overlay. Starting Fn-esse To access Fn-esse, click Start, All Programs, Toshiba, Utilities and Fn-esse. The Fn-esse keyboard appears. Sample Fn-esse keyboard...
Page 154: Assigning A Key To A Program Or Document
Toshiba Utilities Fn-esse The keys are color-coded as follows: ❖ Available keys are white. ❖ Assigned keys and keys associated with a popup list are shown on the Fn-esse keyboard in the selected color. ❖ Unavailable keys are dark gray.
Page 155 Select the desired folder. The left side of the Application Explorer window displays the folders in the Programs menu. The right side lists the programs and documents in the folder. These are the items that appear in the popup list. Toshiba Utilities Fn-esse key, then press...
Page 156: Viewing Existing Key Assignments
Toshiba Utilities Fn-esse ❖ To create a popup list with items from various folders, or to pick only a few items from a folder, create a new folder containing only the desired programs and documents. If you are unsure how to do this, refer to your operating system documentation.
Page 157: Hotkey Utility
TOSHIBA Console The TOSHIBA Console provides quick access to computer functions and allows you to customize a range of computer settings. To access the TOSHIBA Console, do one of the following: ❖ Double-click the TOSHIBA Console icon on the desktop.
Page 158 ❖ Use the Start menu. If you use the Start menu, do the following: Click Start, then click All Programs. Point to TOSHIBA, then Utilities, then click the resulting Console selection. The TOSHIBA Console window appears. Sample TOSHIBA Console window The TOSHIBA Console offers the following features: ❖...
Page 159: Customize Your Computer
(See “Fn-esse” on page ❖ Toshiba Hardware (See “Toshiba Hardware Setup” on page ❖ ConfigFree (See “Using ConfigFree™ with your Toshiba Computer” on page Security The features available in this category are: ❖ Supervisor password ❖ User password Power Management The Power Management feature enables you to control your computer’s power usage, regardless of the source, and use the...
Page 160 You can either use one of the preset modes or create and use your own customized profile. The preset profiles cannot be deleted. By changing the options that appear in the TOSHIBA Power Saver Properties window and clicking OK, you can reconfigure that function. Any options that you change become effective when you click either OK or Apply.
Page 161: Toshiba Hardware Setup
Keep in mind however, that by default, these actions will apply to all profiles. Toshiba Hardware Setup Toshiba Hardware Setup is the Toshiba configuration management tool. To access it: In the TOSHIBA Console, click the Toshiba Hardware icon. Toshiba Utilities TOSHIBA Console...
Page 162 Toshiba Utilities TOSHIBA Console Sample TOSHIBA HWSetup window The TOSHIBA HWSetup window appears with tabs for the following: ❖ Boot Priority — Allows you to change the sequence in which your computer searches the drives for the operating system. You can also manually choose the Boot Priority by pressing the power button, then quickly pressing the key, or the right or left arrow keys.
Page 163: Toshiba Zooming Utility
Microsoft Office ❖ Windows Media Player ❖ Adobe Reader ❖ Icons on the desktop To configure the Toshiba Zooming Utility, double-click the Toshiba Zooming Utility on the task bar. The TOSHIBA Zooming utility screen appears. Toshiba Utilities TOSHIBA Zooming Utility...
Page 164: Application Launch Button
Initially, the button is assigned to launch Internet Explorer. You can reassign the button to launch Microsoft Outlook, TOSHIBA Console, TV Out, as well as browse for specific applications. key and press key and press ;...
Page 165: Chapter 6: If Something Goes Wrong
This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter.
Page 166 If Something Goes Wrong Problems that are easy to fix To close a program that has stopped responding: Press Ctrl The Windows Task Manager window appears. Click the Applications tab. If a program has stopped responding, the words “not responding” appear beside its name in the list. Select the program you want to close, then click End Task.
Page 167: Problems When You Turn On The Computer
Press Enter describing what you were doing when you received the message. Save the file and refer to it when you contact the software manufacturer. Problems when you turn on the computer These problems may occur when you turn on the power. The computer will not start.
Page 168: The Windows Operating System Is Not Working
If Something Goes Wrong The Windows diskette drive, press the left or right arrow key and choose your boot-up device. HINT: Press F12 as you power on the computer to access the boot priority menu. The computer displays the message. The computer was placed in Standby mode and the battery has discharged.
Page 169: Using Startup Options To Fix Problems
The Windows ❖ The operating system responds differently from the normal routine. ❖ The screen does not look right. Unless a hardware device has failed, problems usually occur when you change the system in some way such as installing a new program or adding a device.
Page 170: Internet Problems
If Something Goes Wrong The Windows ❖ Reboot ❖ Return to OS Choices Menu See your Windows TECHNICAL NOTE: If your computer is connected to a network, the Startup menu may display different versions of Safe mode. Internet problems My Internet connection is very slow. Many factors contribute to the speed with which you can surf the Internet.
Page 171: Resolving A Hardware Conflict
To access Windows Click Start, then click Help and Support. The Help and Support Center window appears. Then do one or both of the following: ❖ In the search field, type in the topic of the problem with which you need help and follow the on-screen instructions.
Page 172: Resolving Hardware Conflicts On Your Own
If Something Goes Wrong Resolving a hardware conflict The recommended procedure for getting multiple devices to work together is to add and set up one device at a time. After you add each device, test it to make sure it and all previously connected devices work.
Page 173 Plug and Play With Plug and Play and the Windows avoiding hardware conflicts is easy. Plug and Play is a computer standard that helps the system BIOS (basic input/ output system) and the operating system to automatically assign resources to Plug and Play-compliant devices. In theory, if every device connected to the computer is Plug and Play-compliant, no two devices will compete for the same system resources.
Page 174: Fixing A Problem With Device Manager
If Something Goes Wrong Resolving a hardware conflict Fixing a problem with Device Manager Device Manager provides a way to check and change the configuration of a device. Changing the default settings using Device Manager can cause other conflicts that make one or more devices unusable. Device Manager is a configuration tool for advanced users who understand configuration parameters and the ramifications of changing them.
Page 175 To check a device’s properties: Click Start, Control Panel, Performance and Maintenance, Administrative Tools. Double-click the Computer Management icon. In the left pane, click Device Manager. To view the device(s) installed, double-click the device type. To view the properties, double-click the device. The operating system displays the Device Properties window, which provides an array of tabs.
Page 176: Memory Module Problems
If Something Goes Wrong Resolving a hardware conflict Memory module problems Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up. To avoid damaging the memory module, be careful not to touch its gold connector bar (on the side you insert into the computer).
Page 177: Power And The Batteries
Power and the batteries Your computer receives its power through the AC adapter and power cable or from the system batteries (main battery and real-time clock (RTC) battery). Power problems are interrelated. For example, a faulty AC adapter or power cable will neither power the computer nor recharge the batteries.
Page 178: Keyboard Problems
If Something Goes Wrong Resolving a hardware conflict If the battery light does not glow after 20 minutes, the battery may have reached the end of its useful life. Try replacing it. The battery appears not to power the computer for as long as it usually does.
Page 179: Display Problems
You have connected an external keyboard and the operating system displays one or more keyboard error messages. If you have a second keyboard, try it. If it works, the first keyboard may be defective or incompatible with your computer. Display problems Here are some typical display problems and their solutions: The display is blank.
Page 180 If Something Goes Wrong Resolving a hardware conflict If you are using an external monitor: ❖ Check that the monitor is turned on. ❖ Check that the monitor’s power cable is firmly plugged into a working power outlet. ❖ Check that the cable connecting the external monitor to the computer is firmly attached.
Page 181 To change the display properties: Point at the desktop and click with the secondary button. The Display Properties window appears. Click Properties, then click the Settings tab. Adjust the screen resolution and/or color quality. Click OK. The display mode is set to Simultaneous and the external display device does not work.
Page 182: Disk Drive Problems
If Something Goes Wrong Resolving a hardware conflict Disk drive problems Problems with the hard disk or with a diskette drive usually show up as an inability to access the disk or as sector errors. Sometimes a disk problem may cause one or more files to appear to have garbage in them.
Page 183 Your hard disk seems very slow. If you have been using your computer for some time, your files may have become fragmented. Run Disk Defragmenter. To do this, click Start, then click All Programs, point to Accessories and System Tools, and click Disk Defragmenter.
Page 184: Dvd-Rom Or Multi-Function Drive Problems
If Something Goes Wrong Resolving a hardware conflict The drive cannot read a diskette. Try another diskette. If you can access the second diskette, the first diskette (not the drive) is probably causing the problem. Run Error-checking on the faulty diskette (for instructions, see DVD-ROM or multi-function drive problems You cannot access a disc in the drive.
Page 185 Some discs run correctly, but others do not. If the problem is with an application CD-ROM, refer to the software’s documentation and check that the hardware configuration meets the program’s needs. The color of the materials used to make the disc can affect its reliability.
Page 186: Sound System Problems
If Something Goes Wrong Resolving a hardware conflict Sample Secondary IDE Channel Properties window Click the Advanced Settings tab. Look at Device 0. The current transfer mode should be Ultra DMA Mode 2. If it is not, select Ultra DMA Mode 2 from the pull-down menu and click OK.
Page 187: Pc Card Problems
If Something Goes Wrong Resolving a hardware conflict in the Mixer Utility (default Enabled), may cause feedback. Revert to the default settings. PC Card problems PC Cards (PCMCIA-compatible) include many types of devices, such as a removable hard disk, additional memory, or a pager.
Page 188 If Something Goes Wrong Resolving a hardware conflict PC Card checklist ❖ Make sure the card is inserted properly into the slot. “Using PC Cards” on page 148 Cards. ❖ Make sure all cables are securely connected. ❖ Occasionally a defective PC Card slips through quality control.
Page 189 The computer stops working (hangs) when you insert a PC Card. Remove the PC Card. If removing the PC Card does not resolve the problem, try restarting the computer. If the computer still does not work, contact the PC Card’s manufacturer.
Page 190: Printer Problems
If Something Goes Wrong Resolving a hardware conflict Printer problems This section lists some of the most common printer problems: The printer will not print. Check that the printer is connected to a working power outlet, turned on and ready (on line). Check that the printer has plenty of paper.
Page 191: Modem Problems
4800, 9600, 14400, 28800, 33600 bps (bits per second) or higher. Refer to the program’s documentation and the modem guide for information on how to change these settings. For more information, visit toshiba.com. The modem is on, set up properly and still will not transmit or receive data.
Page 192: Develop Good Computing Habits
If Something Goes Wrong Develop good computing habits Develop good computing habits Make sure you are prepared. Save your work frequently. You can never predict when your computer will lock, forcing you to close a program and lose unsaved changes. Many software programs build in an automatic backup, but you should not rely solely on this feature.
Page 193: If You Need Further Assistance
GO, and then clicking the Detailed Specs link from the menu on the left. Or just refer to the computer documentation shipped with your product. For the number of a Toshiba dealer, see contact” on page If Something Goes Wrong...
Page 194: Contacting Toshiba
To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at accessories.toshiba.com. Toshiba voice contact Before calling Toshiba, make sure you have: ❖...
Page 195: Other Toshiba Internet Web Sites
Other Toshiba Internet Web sites toshiba.com computers.toshiba.com www.toshiba.ca www.toshiba-Europe.com www.toshiba.co.jp/index.htm http://servicio.toshiba.com Toshiba’s worldwide offices Australia Toshiba (Australia) Pty. Limited 84-92 Talavera Road North Ryde NSW 2113 Sydney Australia France Toshiba Systèmes (France) S.A. 7, Rue Ampère; B. P. 131 92800 Puteaux Cédex...
Page 196 Toshiba America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 United States For more information on additional Toshiba worldwide locations, please visit: www.toshiba.co.jp/index.htm. Mexico Toshiba de México S.A. de C.V. Sierra Candela No.111, 6to. Piso Col. Lomas de Chapultepec.
Page 197: Appendix A: Hot Keys
Appendix A Hot Keys Hot keys are keys that, when pressed in combination with the key, turn system functions on and off. Hot keys have a legend on or above the key indicating the option or feature the key controls. Volume Mute This hot key enables/disables volume mute on your computer.
Page 198: With A Password
Hot Keys Instant password security make the display’s content reappear, if no password is set for the current user. With a password key combination turns off the display and activates Fn + F1 instant security. If you set a blank screen saver, pressing the combination to activate instant security will cause the screen to go blank.
Page 199: Power Usage Mode
To set up a password with a screen saver, go to Windows Help for instructions: Click Start, Help and Support. In the Search field, type Press Enter Click the Protect your files with a screen saver password link located under the suggested topics. Follow the steps listed in the Windows password-protected screen saver.
Page 200: Standby Mode
Hot Keys Standby mode Standby mode This hot key puts the computer into Standby mode. Sample Standby confirmation box ❖ A message box is displayed by default to confirm that the computer is going into Standby mode. This message box can be set so it does not display.
Page 201: Hibernation Mode
Hibernation mode This hot key puts the computer into Hibernation mode. Sample Hibernation confirmation box Hibernation mode ❖ If Hibernation mode is enabled (the default) a message box is displayed by default to confirm the computer is going into Hibernation mode. The message box can be set so it does not display.
Page 202: Display Modes
Hot Keys Display modes Display modes This hot key cycles through the power-on display options. The display modes are: In order to use a simultaneous mode, you must set the resolution of the internal display panel to match the resolution of the external display device. Display brightness Sample display brightness window ❖...
Page 203: Disabling Or Enabling The Touchpad
For more information, see Zooming Utility” on page This hot key turns the Zooming utility to zoom- out. For more information, see Zooming Utility” on page “Overlay keys” on page Hot Keys “Disabling or enabling “TOSHIBA 163. “TOSHIBA 163.
Page 204: Appendix B: Power Cable Connectors
Appendix B Power Cable Connectors Your notebook computer features a universal power supply you can use worldwide. This appendix shows the shapes of the typical AC power cable connectors for various parts of the world. USA and Canada UL approved CSA approved Australia AS approved...
Page 205: Appendix C: Using Configfree™ With Your Toshiba Computer
Appendix C Using ConfigFree™ with your Toshiba Computer ConfigFree™ is a set of utilities that makes it easy to control communication devices and network connections. ConfigFree also lets you identify communication problems and create profiles for easy switching between locations and communication networks.
Page 206: Getting Started
Networking, ConfigFree. ❖ Double-click the ConfigFree icon ❖ Press the Toshiba Console button (if applicable to your system) to open the Toshiba Console, and then click the ConfigFree icon. ❖ Click the ConfigFree icon click the desired utility. If your computer is not connected to a network, the ConfigFree NOTE icon on the taskbar is displayed with an “X.”...
Page 207: Configfree Utilities
Sample ConfigFree Launcher ConfigFree Utilities Connectivity Doctor The Connectivity Doctor lets you analyze your network connections and fix network-connection problems. Using Connectivity Doctor, you can view detailed network information by simply moving the mouse pointer. The Connectivity Doctor works with the following network devices: ❖...
Page 208 ConfigFree Utilities Sample Connectivity Doctor screen Moving the mouse pointer over a wired or wireless network device icon displays information about the device, such as its IP address, subnet mask, and MAC address. A wireless network device also shows information such as the network SSID and the device’s Wired Equivalent Privacy (WEP) key settings.
Page 209 If a problem, or potential problem, is detected, a triangle containing an exclamation point appears in the Connectivity Doctor screen and an orange frame describes the relevant location. You can then view a possible cause and solution for the problem by clicking the exclamation point. For example, if the connection to a wireless network cannot be established because the wireless communication switch is turned off, an exclamation point appears next to the wireless...
Page 210: Search For Wireless Devices
ConfigFree Utilities Search for Wireless Devices The Search for Wireless Devices utility searches for wireless LAN devices and Bluetooth devices currently used in the neighborhood, and displays information about them on a virtual map. To search for wireless devices: Click the Click Search for Wireless Devices.
Page 211 ConfigFree Utilities Sample viewing Wi-Fi devices The following screen shows an example of Bluetooth devices that are detected. As with the Wi-Fi screen, moving the mouse pointer over a device icon displays information about the device. Sample viewing Bluetooth devices You can connect to devices shown on the Bluetooth map: Click the icon of a Bluetooth device.
Page 212: Profile Settings
ConfigFree Utilities Click your own computer at the center of the map. Configured devices are automatically connected. Devices not yet configured launch the Add New Connection Wizard, where you can configure and connect to the device. Profile Settings The Profile Settings utility lets you save network settings in “profiles.”...
Page 213 ❖ Personal firewall settings for Internet connections. ❖ Dial-up connection settings for the default connection. ❖ File and printer sharing settings. ❖ Printer settings for the default printer. To create a profile: Click the icon in the system tray. Move the pointer to Profile. Click Add.
Page 214: Quick Connect
Quick Connect The Quick Connect feature switches the Wireless LAN connection to connect to a Toshiba Wireless Projector. Once the projector utility is installed, launching the Quick Connect utility automatically opens the Wireless Data Projector Application.
Page 215 (DPJ), then click Connect. Launching Quick Connect prevents you from using the network to connect to a Toshiba Wireless Projector when the wireless LAN Configuration is set to Ad hoc. If you are connected to an access point, the connection is broken and re- established later.
Page 216 Quick Connect function was started: ❖ If the Toshiba Wireless Projector utility is closed. ❖ If you select Toshiba Wireless Projector (DPJ) from the ConfigFree tray menu (this disconnects the wireless LAN connection). ❖ If you select a profile from the ConfigFree tray menu or when you disable a wireless device.
Page 217: Using The Automatic Switch
Using the Automatic Switch The Automatic Switch feature allows the computer to automatically switch profiles the next time it is powered on. This feature is particularly useful if you want your computer to automatically switch from the network configuration you use in your office to the one you use at home.
Page 218: Semi-Automatic Switch Feature
Semi-Automatic Switch Feature Semi-Automatic Switch Feature The Semi-Automatic feature alerts you when the computer connects to a Service Set Identifier (SSID) stored in a profile, When the computer connects to the designated SSID, a notification window appears. You can then click this window to connect using the settings specified in the profile.
Page 219: Glossary
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide. BIOS CD-ROM CD-RW CMOS COM1 COM2 alternating current basic input/output system bits per second compact disc compact disc read-only memory compact disc rewrite memory...
Page 220 Glossary DIMM DSTN DVD-ROM digital versatile (or video) disc read-only memory EPROM HTML IEEE LPT1 MIDI NTFS PCMCIA direct memory access dual inline memory module disk operating system dots per inch dual supertwist nematic digital versatile (or video) disc enhanced capabilities port erasable programmable read-only memory file allocation table Federal Communications Commission...
Page 221 SCSI SDRAM SRAM SVGA Terms The following terms may appear in this user’s guide. active-matrix display — A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology. Also known as a “TFT display,” in its simplest form there is one thin film transistor (TFT) for each cell.
Page 222 Glossary application — A computer program that you use to perform tasks of a specific type. Applications include word processors, spreadsheets, and database management systems. See also program. backup — A copy of a file, usually on a removable disk, kept in case the original file is lost or damaged.
Page 223 byte — A sequence of eight bits. A byte is the smallest addressable unit of data. See also bit, gigabyte, kilobyte, megabyte. cache — A section of very fast memory in which frequently used information is duplicated for quick access. Accessing data from cache is faster than accessing it from the computer’s main memory.
Page 224 Glossary controller — A device that controls the transfer of data from a computer to a peripheral device and vice versa. For example, disk drives, monitors, keyboards, and printers all require controllers. CPU — See central processing unit (CPU). CPU cache — A section of very fast memory residing between the CPU and the computer’s main memory that temporarily stores data and instructions the CPU will need to execute commands and programs.
Page 225 disk — A round, flat piece of material that can be magnetically influenced to hold information in digital form, and used in the production of magnetic disks, such as diskettes and hard disks. Compare disc. See also diskette, hard disk. disk drive —...
Page 226 Glossary enable — To turn on a computer option. See also disable. executable file — A computer program that is ready to run. Application programs and batch files are examples of executable files. Names of executable files usually end with a .bat or .exe extension. extension —...
Page 227 — The physical components of a computer system. Compare software. Hibernate — A feature of many Toshiba notebook computers that saves to the hard disk the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned off.
Page 228 Glossary keyboard shortcut — A key or combination of keys that you use to perform a task instead of using a pointing device such as the TouchPad. kilobyte (KB) — A unit of data equal to 1024 bytes. See also byte. L1 (level one) cache —...
Page 229 microprocessor — See central processing unit (CPU). MIDI (Musical Instrument Digital Interface) — A standard for connecting musical instruments, synthesizers, and computers. The MIDI standard provides a way of translating music into a form computers can use, and vice versa. modem —...
Page 230 Glossary operating system — A set of programs that controls how the computer works. Examples of operating systems are Windows Edition and Windows palette — See color palette. parallel — Processes that occur simultaneously. In communications, it means the transmission of more than one bit of information at a time.
Page 231 properties — The attributes of an object or device. For example, the properties of a file include the file’s type, size, and creation date. RAM (random access memory) — Volatile memory that can be written to as well as read. By volatile, we mean that information in RAM is lost when you turn off your computer.
Page 232 Glossary serial — Processes that occur one at a time. In communications, it means the transmission of one bit at a time sequentially over a single channel. On your computer, the serial port provides a serial interface between the computer and an appropriate device. Compare parallel. shortcut —...
Page 233 Web — See World Wide Web. Wi-Fi — A trademarked term by the Wireless Capability Ethernet Alliance which stands for Wireless Fidelity, and is another term for the communication protocol to permit an Ethernet connection using wireless communication components. World Wide Web (www) — The worldwide network of Web sites linked together over the Internet.
Page 234: Index
Index AC adapter 48, 50 AC power light accessories memory alarms low battery audio features Auto-Run avoiding injury battery alarms caring for changing charge not lasting 51, 75, 119 charging disposal installing 50, 121 light monitoring power power usage mode removing button start...
Page 235 inserting problem solving channels charging 51, 119 main battery checking device properties cleaning CD or DVDs computer comfort chair lighting work habits command Shut down Turn Off commands Hibernate powering down Standby communications network connection system resources compact discs inserting problem solving removing computer...
Page 236 TOSHIBA Touch and Launch disabling/enabling TouchPad Disk Defragmenter disk drive corrupted/damaged data files missing files/trouble accessing a disk running slow diskette drive cannot insert a diskette cannot read a diskette external display does not look normal/flickers external monitor not working...
Page 237 file names files 80, 91 backing up printing restoring 79, 88 saving Fn key assigning functions Fn-esse assigning keys change/remove key assignments drag-and-drop keyboard starting using keyboard viewing key assignments function keys hard disk drive light hardware conflicts resolving Help Windows XP Hibernate restarting...
Page 238 jack RJ-11 keyboard character keys Ctrl, Fn, and Alt keys cursor control overlay external Fn-esse function keys hot keys 167, 179 not working numeric keypad overlay overlay keys unexpected characters Windows special keys lights 48, 50 AC power 50, 121 battery hard disk drive main battery...
Page 239 PC Card inserted computer will not power up contacting Toshiba corrupted/damaged data files Device Manager 174, 175 disabling a device disk drive is slow display is blank...
Page 240 AC adapter 39, 46, 63 computer printer TOSHIBA Touch and Launch TOSHIBA Touch and Launch using .wav files problem solving...
Page 241 Error-checking system tray taskbar Toshiba Internet Web sites Toshiba Accessories information TOSHIBA Console Toshiba Hardware Setup TOSHIBA Touch and Launch disable/enable TouchPad disabling/enabling traveling tips Turn Off Turn Off command Turn Off methods turning computer on/off Universal Resource Locator (URL)
Page 242 Windows Explorer Windows Media Player Windows Standby Windows Start menu Windows XP Help Help and Support problem solving Windows XP Professional taskbar Windows® XP Professional desktop wireless interoperability wireless networking Wizards Add Printer Dial-Up Networking Wizard Zooming Utility...

Toshiba A60-S156 User Manual

Chapter 1: Getting Started

Chapter 2: Learning the Basics

Chapter 3: Mobile Computing

Chapter 4: Exploring Your Options

Chapter 5: Toshiba Utilities

Chapter 6: If Something Goes Wrong

Appendix A: Hot Keys

Appendix B: Power Cable Connectors

Appendix C: Using Configfree™ with Your Toshiba Computer

Quick Links

Related Manuals for Toshiba A60-S156

Summary of Contents for Toshiba A60-S156