1. Manuals
  2. Brands
  3. Central Pneumatic Manuals
  4. Nail Gun
  5. 68021
  6. Set up and operating instructions manual

Central Pneumatic 68021 Set Up And Operating Instructions Manual

2" 18 gauge brad nailer
Hide thumbs Also See for 68021:
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Central Pneumatic 68021

Summary of Contents for Central Pneumatic 68021

  • Page 2: Safety Alert Symbol And Signal Words

    TO A RISK OF FIRE, ELECTRIC could result in minor or moderate injury. SHOCK, OR INJURY TO PERSONS NOTICE is used to address practices not related to personal injury. Page 2 For technical questions, please call 1‑888‑866‑5797. SKU 68021...

  • Page 3: Work Area

    WARNING – Remove finger from the trigger when not driving fasteners. SKU 68021 For technical questions, please call 1‑888‑866‑5797. Page 3...

  • Page 4: Air Source

    Such maintained tools. There is a risk of gases are capable of explosion and bursting if the tool is damaged. serious injury to persons. Page 4 For technical questions, please call 1‑888‑866‑5797. SKU 68021...
  • Page 5 12. Disconnect tool from air supply when: 22. Obey the manual for the air compressor used to power this tool. a. Unattended. b. Performing any maintenance or repair. SKU 68021 For technical questions, please call 1‑888‑866‑5797. Page 5...
  • Page 6 SAVE THESE but must be supplied by operator. INSTRUCTIONS. Vibration Precautions This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, Page 6 For technical questions, please call 1‑888‑866‑5797. SKU 68021...

  • Page 7: Functional Description

    9 for Air Tool Setup procedures. SAFETY INFORMATION section at the beginning of this Note: If an automatic oiler system is not manual including all text under used, add a few drops of Pneumatic SKU 68021 For technical questions, please call 1‑888‑866‑5797. Page 7...
  • Page 8 Air Tool & Spray Gun Portable Setup Page 8 For technical questions, please call 1‑888‑866‑5797. SKU 68021...
  • Page 9 Air Tool & Spray Gun Stationary Setup SKU 68021 For technical questions, please call 1‑888‑866‑5797. Page 9...
  • Page 10 Adjust the pressure gradually, while checking the air output gauge to set the right pressure range. The air pressure setting must not exceed job site regulations/restrictions. The air Page 10 For technical questions, please call 1‑888‑866‑5797. SKU 68021...

  • Page 11: Operating Instructions

    Release the trigger, slide the nailer to the Trigger. It should only fire again if the a fresh piece of wood, and squeeze it trigger is released and squeezed again. The again. SKU 68021 For technical questions, please call 1‑888‑866‑5797. Page 11...

  • Page 12: Loading The Tool

    After use, to prevent accidents: the zero (“0”) marker indicating 15 a. Release the Trigger. pieces and 5-piece marker increments thereafter. b. Detach the air supply. Page 12 For technical questions, please call 1‑888‑866‑5797. SKU 68021...
  • Page 13 Tool. TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise, vibration, or leaking air is detected, have problem corrected before further use. SKU 68021 For technical questions, please call 1‑888‑866‑5797. Page 13...

  • Page 14: Clearing Jams

    If a fastener is jammed in the Drive Guide, pull on the Quick Release Lever (44) and disengage the Quick Release Spring (45). Remove the jammed fastener; pliers maybe necessary to remove a stuck fastener. Page 14 For technical questions, please call 1‑888‑866‑5797. SKU 68021...

  • Page 15: Troubleshooting

    3. Replace damaged components. 4. Dirty, worn or damaged valve. 4. Clean or replace valve assembly. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect air supply before service. SKU 68021 For technical questions, please call 1‑888‑866‑5797. Page 15...

  • Page 16: Please Read The Following Carefully

    Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Page 16 For technical questions, please call 1‑888‑866‑5797. SKU 68021...
  • Page 17 Assembly Diagram SKU 68021 For technical questions, please call 1‑888‑866‑5797. Page 17...
  • Page 18 Limited 1‑Year Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the date of purchase (90 days if used by a professional contractor or if used as rental equipment).

Table of Contents