Table of Contents
Advertisement
Owner's Manual & Safety Instructions
Save This Manual
inspection, maintenance and cleaning procedures. Write the product's serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.
framing nailer
28° angle
ITEM 68068
REV 12a
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-800-444-3353 as soon as possible.
©
Copyright
2010 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly, operating,
Visit our website at: http://www.harborfreight.com
Email our technical support at: tech@harborfreight.com
®
. All rights reserved.
21° angle
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
ITEM 68028
Advertisement
Table of Contents
Related Manuals for Central Pneumatic 68068
Summary of Contents for Central Pneumatic 68068
- Page 1 No portion of this manual or any artwork contained herein may be reproduced in Failure to do so can result in serious injury. any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing SAVE THIS MANUAL.
-
Page 2: Table Of Contents
National pipe thread, straight NIOSH-approved dust mask/respirator. WARNING marking concerning WARNING marking concerning Risk of Eye Injury. Wear ANSI-approved Risk of Explosion. safety goggles with side shields. Table A: Symbol Definitions Page 2 For technical questions, please call 1-800-444-3353. Item 68028 68068... -
Page 3: Work Area
A dust mask, non-skid safety shoes and finger on trigger, the tool is able to fire a fastener. a hard hat must be used for the applicable conditions. Wear heavy-duty work gloves during use. Item 68028 For technical questions, please call 1-800-444-3353. Page 3 68068... -
Page 4: Tool Use And Care
Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air-pressure range. SAVE THESE INSTRUCTIONS. Page 4 For technical questions, please call 1-800-444-3353. Item 68028 68068... - Page 5 17. Keep clear of the workpiece near the area being fastened. Fasteners may bend sideways during firing, causing them to exit the workpiece at an unexpected point, causing personal injury. Item 68028 For technical questions, please call 1-800-444-3353. Page 5 68068...
-
Page 6: Specifications
2″ to 3-1/2″ Long Fastener Type Air Consumption ITEM 68028: 3.5 CFM ITEM 68068: @ 90 PSI ITEM 68068: 2 CFM 28º Full or Clipped Head Nails, Safety Mechanism Single Sequential 2-3/16″ to 3-9/16″ Long Magazine Capacity 40 Components and Controls... -
Page 7: Operation
3. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working. Item 68028 For technical questions, please call 1-800-444-3353. Page 7 68068... - Page 8 Page 8 For technical questions, please call 1-800-444-3353. Item 68028 68068...
- Page 9 Item 68028 For technical questions, please call 1-800-444-3353. Page 9 68068...
- Page 10 The tool must not cycle (fire). If it cycles (fires), to act in the manner explained in bold, have it stop immediately and have it repaired repaired by a qualified service technician. by a qualified service technician. Page 10 For technical questions, please call 1-800-444-3353. Item 68028 68068...
-
Page 11: Loading The Tool
Store indoors out of children’s reach. 7. Move the Nailer to another spot on the workpiece and squeeze the Trigger again to fire another nail. Continue firing nails as needed. Item 68028 For technical questions, please call 1-800-444-3353. Page 11 68068... -
Page 12: Maintenance
Use a screwdriver to release the jammed fastener by probing the openings in the magazine. 4. If the jam cannot be cleared using the method above, have the tool serviced by a qualified technician. Page 12 For technical questions, please call 1-800-444-3353. Item 68028 68068... -
Page 13: Troubleshooting
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Item 68028 For technical questions, please call 1-800-444-3353. Page 13 68068... -
Page 14: Parts List And Diagram
Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Page 14 For technical questions, please call 1-800-444-3353. Item 68028 68068... - Page 15 Assembly Diagram Item 68028 For technical questions, please call 1-800-444-3353. Page 15 68068...
-
Page 16: Warranty
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.