Advertisement
TV Connecting to the EURO AV2 DECODER jack Connect a VCR or similar recording device to the EURO AV2 DECODER jack of this recorder. TV VCR,
Cable Box, or Satellite Tuner, etc. Rear of the HDD/DVD Recorder Receiver PAY-TV/Canal Plus Decorder SCART AV Tip: You do not need to turn on the
recorder to view the signals from the connected tuner on your TV. Notes: Pictures containing copy protection signals that prohibit any copying cannot be
recorded. If you pass the recorder signals via the VCR, you may not receive a clear image on your TV screen. Be sure to connect your VCR to the recorder
and your TV in the order shown below. To watch video tapes, watch the tapes through a second line input on your TV. Line input 1 VCR RECORDER TV Line
input 2 Rear of the HDD/DVD Recorder Receiver When you record to a VCR from this recorder, do not switch the input source to TV by pressing the
TV/DVD button on the remote. If you are using a B Sky B tuner, be sure to connect the tuner's VCR SCART jack to the EURO AV2 DECODER jack. If you
disconnect the recorder's mains lead, you will not be able to view the signals from the connected VCR or tuner.
14 Connecting to the INPUT 3 or INPUT 4 Jacks Connect the input jacks (AV3, AV4) on the recorder to the audio/video out jacks on your accessory
component, using audio/video cables. Note: If you use the S-VIDEO IN jack on the front panel, the VIDEO IN jack on the front panel is not available. Jack
panel of Accessory Component (VCR, Camcorder, etc.) VIDEO OUTPUT Connecting a Digital Camcorder Using the front panel DV IN jack, it is possible to
connect a DV digital camcorder and digitally transfer DV tapes to DVD. Use a DV cable (not supplied) to connect the DV in/out jack of your DV camcorder
AUDIO OUTPUT R DV Digital Camcorder DV IN/OUT L S-VIDEO OUTPUT OR OR Front of the HDD/DVD Recorder Receiver Rear of the HDD/DVD
Recorder Receiver Front of the HDD/DVD Recorder Receiver Radio Antenna Connections Connect the supplied FM/AM antennas for listening to the radio.
Connect the AM loop antenna to the AM antenna connector. Connect the FM wire antenna to the FM antenna connector. Notes: To prevent noise pickup, keep
the AM loop antenna away from the HDD/DVD Recorder Receiver System and other components. Be sure to fully extend the FM wire antenna.
After connecting the FM wire antenna, keep it as close to horizontal as possible. 15 Hookup and Settings Note: This jack is for connection to DV digital
camcorder only. It is not compatible with digital satellite tuners or D-VHS video decks. Assembling and Connecting to the Speakers The speakers are
detached from the speaker stands. Connect the speaker cables and assemble the speakers from speaker stands as illustrated. How to connect the Speakers
Connect the speaker cables to the appropriate terminals on the bottom of each front speaker. After connecting the speaker cables to the appropriate terminals
on the bottom of each front speaker and attach the front speakers to the speaker stands. About Ferrite Core (Optional) Be sure to attach the ferrite core to the
System cable and power cord (for connecting to this unit). This ferrite core can reduce noises. To attach the speaker to the stand How to attach the ferrite
Press the stopper [a] of the ferrite core to open. 2. Insert the System cable to the ferrite core and wind the power cord once on the ferrite core. 3. Close the
ferrite core unit it clicks. Note: Attach the ferrite core near the unit (Refer to the fig.3 and comment.). Note: If you hold the top of speakers when carring the
front or rear one, it may cause the seperation of speakers. Therefore it might be damaged.
16 The length here is short as much as possible. Speaker System Connections Connect the SYSTEM to the SYSTEM SELECTOR rear of the Active Subwoofer
Speaker, using the supplied System cable. Connect the speakers using the supplied speaker cables.
to the front panel DV IN jack of this recorder.
core 1.
Advertisement
