Sony Trinitron KV-32XBR400 Service Manual page 26

µ
Device Name: PD64082GF { 3D-Comb Filter / NEC } / IC3501 (BC-board) / P/N: 8-759-594-44 (SB#: V7372)
Slave Address: B8h (Write Address) / B9h (Read Address)
Register
Control Register
No & Name
Function & Link
0 NRMD Operation mode setting
Y-output correction
1 YAPS
(V-aperture compensation & Y-peaking filtering)
2 CLKS System clock setting
3 NSDS Selection for standard/non-satndard signal processing
4 MSS Selection for inter-frame/inter-line processing
5 KILS Killer processing selection
C-signal phase with respect to the Y-signal
6 CDL
(Fine adjustment at 70 ns/step)
NRMD Setting-based Control Table for DYCO, DYGA, DCCO, DCGA
7 DYCO DY detection coring level (Y motion detection coring)
8 DYGA DY detection gain (Y motion detection gain)
9 DCCO DC detection coring level (C motion detection coring)
10 DCGA DC detection gain (C motion detection gain)
11 YNRL Frame recersive YNR nonlinear filter limit level
12 CNRL Frame recersive CNR nonlinear filter limit level
Hysteresis for Hsync non-standard signal detection
13 VTRH
(out-of-Hsync intra-field)
Sensitivity for Hsync non-standard signal detection
14 VTRR
(out-of-Hsync intra-field)
Sensitivity for frame non-standard signal detection
15 LDSR
(out-of-Hsync inter-frame)
VM&SNNR Setting-based Control Table for VAPG & VAPI
VAPG= VAPG1 - VAPG2
16 VAPG V-aperture compensation gain
17 VAPI V-aperture compensation convergence point
SNNR Setting-based Control Table for YPFT & YHFG
18 YPFT Y peaking filter (BPF) center frequency
19 YPFG Y peaking filter (BPF) gain
Note:
3D-COMB / µPD64082
DX1A SERVICE LIST (#1):
Data Data
Type Range
0~3
C 0~3
C 0~3
0~3
C 0~3
C 0~3
C 0~7
0~15
0~15
0~15
0~15
C 0~3
C 0~3
0~3
0~3
0~3
0~7
0~31
0~3
0~15
(Part-1/2)
Data Initial/Average Setting
(32V&36V CRTs)
UHF/VHF & CVideo SVideo
Standard Non-standard Standard Non-standard
0 1 3 3
3
1
UHF/VHF & CVideo SVideo
Standard Non-standard Standard Non-standard
0 0 0 0
0
1
3
NRMD = 0 NRMD = 1 NRMD = 2 NRMD = 3
2 2 2 2
10 10 10 10
5 5 5 5
5 5 5 5
1
1
UHF/VHF Video1~4 Video5&6
Video1~4: CVideo1~4 & SVideo1~3 inputs
1 1 1 Video5&6: YPbPr-480i/480p/1080i inputs
1 1 1
2 2 2
VAPG1 Data Based on MENU/VM Setting
VM = Off VM = Low VM = Mid VM = High
0 2 3 4
4 4 4
SNNR = 0 SNNR = 1 SNNR = 2
0 0 0 0
7 0 1 2
Comment
CVideo (CV): CVideo1~4
inputs
SVideo (SV): SVideo1~3
inputs
C: Common data
VAPG2 Data Based on SNNR/Offset-setting
SNNR = 0 SNNR = 1 SNNR = 2 SNNR = 3
0 0 0
4 or 8
{Initial/CBA Data = 8}
(32V) (36V)
SNNR Setting (-Offset)
SNNR = 3
0
0
3