How To Use The Menu Functions - JVC TM-H1950CG Instructions Manual

HOW TO USE THE MENU FUNCTIONS

DISPLAY AND SELECTION IN THE <MENU>
SCREEN MODE (SETTING)
You can set the following menu items.
Set them depending on your needs.
• APERTURE
• ADJ. BAR POSI.
• COLOR TEMP.
1. Press the MENU button.
MENU
2. Press the CHROMA/PHASE or CONTRAST/BRIGHT
button to select MENU items.
CHROMA CONTRAST
PHASE BRIGHT
APERTURE
ADJ. BAR POSI.
COLOR TEMP.
COLOR SYSTEM
COMPO. LEVEL*
RUSH DELAY
3. Press the VOLUME/SELECT buttons to set.
VOLUME/SELECT
Menu items
APERTURE
ADJ.BAR POSI
COLOR TEMP.
COLOR SYSTEM
COMPO. LEVEL*
RUSH DELAY
* For normal use, leave the COLOR SYSTEM setting to AUTO.
If reception is unsatisfactory in AUTO position, set it to the appropriate color system mode (NTSC or PAL).
* COMPO. LEVEL is displayed only with component serial digital (SDI) input. (Shown with INPUT-C and
INPUT-D except for RGB input.)
4. If you want to set the other menu items, repeat
procedures 2 and 3.
5. Press the MENU button to quit.
MENU
12
• COLOR SYSTEM
• COMPO. LEVEL*
• RUSH DELAY
The <MENU> screen is displayed.
* The on-screen display goes off automatically after about five
minutes with operation performed.
A selection mark (4) is put next to the selected item.
Front panel Function
button displayed
CHROMA/
PHASE
CONTRAST/
BRIGHT
Front panel Function
button displayed
+
VOLUME/
SELECT (+)
4
VOLUME/ –
SELECT (–)
1
Purpose
Picture aperture level
Volume bar position
Color temperature of white
balance
Color system
Component level
Delay time
Front panel Function
button displayed
MENU EXIT
Contents
Forward selection mark (4)
Reverse selection mark (4)
Contents
Increase (to max. value)
Forward the setting value
Decrease (to min. value)
Reverse the setting value
Setting range
00 +01 +39
• • • • • • • • • • • •
LOWER UPPER
6500 9300
AUTO NTSC AUTO PAL
– 40 – 39 – 01 00 +1 +9
• • • •
STD. SLOW
Contents
Quit (or Release) the <MENU>
screen
<MENU> screen
1
< MENU >
4 APERTURE
ADJ. BAR POSI.
COLOR TEMP.
COLOR SYSTEM
COMP. LEVEL
RUSH DELAY
2
EXIT
CHROMA CONTRAST VOLUME/SELECT
PHASE BRIGHT
<Front panel buttons>
1
Selection mark (4): Indicates the
menu item you select.
2
Menu item: Menu items you can
select.
3
Setting display: Indicates the current
settings (value).
4
Function display: The functions of
the front panel buttons (5 buttons on
the left) correspond to the function
displayed.
Function
Contents
displayed
Forward the menu item.
Reverse the menu item.
– Lower the adjustment
value. (to the minimum)
+ Raise the adjustment
value. (to the maximum)
4 Forward the setting value.
1 Reverse the setting value.
+40
EXIT Exits the <MENU> screen.
Note:
● RUSH DELAY sets the delay between
+10
the time the power switch is pressed
and the time power is actually
supplied to the monitor's circuits.
STD. : Power turns on approximately
1 second after the power
switch is pressed.
SLOW : Power turns on approximately
3 seconds after the power
switch is pressed.
* When turning on multiple Color-
Video Monitors simultaneously, it is
recommended to use STD. or
SLOW settings to reduce the rush
current of the entire system.
: 00
: LOWER
: 6500
: AUTO
: 00
: STD.
3
4
MENU