Lighting The Beverage Center; Beverage Center Care; Base Grille; Cleaning - Jenn-Air Overlay BEVERAGE CENTER Use & Care Manual

To remove or adjust the upper glass shelves:
NOTE: The very bottom glass shelf is fixed in place and is not
removable.
1. Remove the shelf by lifting it up and out of the shelf brackets.
2. Remove the two shelf brackets and reposition them in the
desired location.
3. Replace the shelf by inserting it into the shelf brackets.
NOTE: Be sure the shelf is level.

Lighting the Beverage Center

The beverage center has an interior light that comes on anytime
the door is opened. You may also choose to keep the light on at
all times by pressing the left side of the switch, located next to the
temperature control, on the base grille.
NOTES:
Leaving the light on for an extended period of time will slightly
increase the temperature of the beverage center.
The light is an LED which does not need to be replaced. If the
LED does not illuminate when the door is opened, call Service
to replace the light. See Assistance or Service for contact
information.

BEVERAGE CENTER CARE

Base Grille

You must remove the base grille to access the condenser coils for

cleaning.

To remove the base grille:
1. Open the beverage center door to access the base grille.
2. Using a Phillips screwdriver, remove the two screws.
3. Push both tabs in toward the center to release the base grille
from the cabinet and remove.
A
To replace the base grille:
1. Open the beverage center door.
2. Position the base grille so that both tabs align and the base
grille snaps into place. Replace the two screws. Tighten the
screws.
B A
A. Tabs
B. Screws
Cleaning
WARNING
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
Clean the beverage center about once a month to avoid buildup
of odors. Wipe up spills immediately.
To clean your beverage center:
1. Unplug beverage center or disconnect power.
2. Remove all racks and shelves from inside the beverage center.
3. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
To avoid damaging wooden tines and trim pieces, wipe
them off with a clean sponge or soft cloth and warm water.
Do not use detergent or immerse the entire rack into water
when cleaning.
Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, cleaning
waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on plastic parts, interior
and door liners or gaskets. Do not use paper towels,
scouring pads, or other harsh cleaning tools. These can
scratch or damage materials.
To help remove odors, you can wash interior walls with a
mixture of warm water and baking soda (2 tbs to 1 qt
[26 g to 0.95 L] of water).
4. Wash stainless steel and painted metal exteriors with a clean
sponge or soft cloth and a mild detergent in warm water. Do
not use abrasive or harsh cleaners, or cleaners containing
chlorine. These can scratch or damage materials. Dry
thoroughly with a soft cloth.
NOTE: To keep your stainless steel beverage center looking
like new and to remove minor scuffs or marks, it is suggested
that you use the manufacturer's approved Stainless Steel
Cleaner and Polish. To order the cleaner, see "Accessories."
IMPORTANT: This cleaner is for stainless steel parts only!
Do not allow the Stainless Steel Cleaner and Polish to come
into contact with any plastic parts such as the trim pieces,
dispenser covers or door gaskets. If unintentional contact
does occur, clean plastic part with a sponge and mild
detergent in warm water. Dry thoroughly with a soft cloth.
5. Replace the racks and shelves.
6. Clean the condenser coils regularly. They are located behind
the base grille. Coils may need to be cleaned as often as every
other month. This may help save energy.
Remove the base grille. See "Base Grille."
Use a vacuum cleaner with an extended attachment to
clean the condenser coils when they are dusty or dirty.
Replace the base grille.
7. Plug in beverage center or reconnect power.
11