Programming The Guest Mode; Taking Weight Measurement Only; Troubleshooting; Specifications - Tanita BC-350 Instruction Manual

3. Recall Function
The previous readings of the following features can be obtained using the recall function.
Weight
Body Fat %
Total Body Water %
Muscle Mass and Physique Rating
BMR and Metabolic Age
Bone mass
Visceral Fat Level
To obtain previous readings, press the RECALL button while the current readings are being displayed.
To see other previous readings, press the appropriate feature button for each desired reading.
Press the RECALL button again to go back to the current readings.
Note : For children (age 7-17), the unit will only display the Weight and the Body Fat % (it will not display the Healthy
Range Indicator).
Programming the guest mode
Guest mode allows you to programe the unit for a one-time use without resetting a
Personal data number.
Press Guest button to activate the unit. Then follow the steps:
Set Age, Select Female or Male, and Specify Height.
Note : If you step onto the platform before "0.0" appears the display will show "Error"
and you will not obtain a reading.
Taking weight measurement only
Select Weight-Only Key
Press the Weight-only key. After 2 or 3 seconds, "0.0" will appear in the display and the unit
will beep. When "0.0" appears in the display, step onto the platform. The body weight value will
appear. If you remain on the platform, the display will flash for about 30 seconds, and then the
power will automatically turn off.
If you step off the platform, the weight will continue to show for about 5 seconds, then
"0.0" will appear and the unit will shut off automatically.


Troubleshooting

If the following problems occur ...then...
• A wrong weight format appears followed by kg, lb, or st-lb.
Refer to Switching the weight mode on p.3.
• The display shows and goes off when the personal key pressed.
No data (age gender, height and activity level) has been stored in the memory.
• appears on the display, or all the data appears and immediately disappears.
Batteries are low. When this message appears, be sure to replace the batteries immediately, since weak batteries will affect the
accuracy of your measurements. Change all the batteries at the same time with new batteries.
Note : Your settings will not be erased from the memory when you remove the batteries.
• appears while measuring.
Please stand on the platform keeping movement to a minimum.
The unit cannot accurately measure your weight if it detects movement.
The Body Fat Percentage is more than 75%, readings cannot be obtained from the unit.
• The Body Fat Percentage reading does not appear or
Make sure socks or stockings are removed, and the soles of your feet are clean and properly aligned with the guides on the
measuring platform.
• appears while measuring.
Reading cannot be obtained if the weight capacity is exceeded
• No reading is obtained after pressing a feature button.
Step off scale when body fat reading appears, then press feature button.

Specifications

Federal Communications Commission and Canadian ICES Notice
BC-350 This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules and Canadian ICES-003. These limits are designed to provide
Weight Capacity
reasonable protection against harmful interference in a residential installation. This equipment
330lb (150kg) (23st 8lb)
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there
Weight Increments
is no guarantee that interference will not occur in a particular installation. If this equipment does
0.1lb (0.05kg) (0.1lb)
cause harmful interference to radio or television reception, which can be determined by turning the
Body Fat Increments
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
0.1%
• Reorient or relocate the receiving antenna.
Personal Data
• Increase the separation between the equipment and receiver.
4 memories
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
Power Supply
• Consult the dealer or an experienced radio or television technician for help.
2pcs.Lithium batteries CR2032 (included)
Modifications
Power Consumption
The FCC requires the user to be notified that any changes or modifications made to this device
60 mA maximum
that are not expressly approved by Tanita Corporation may void the user's authority to operate the
equipment.
Measuring Current
50 kHz, 500 µA
appears after the weight is measured.
connected.