Table of Contents
Advertisement
The JUPITER-80's System Settings
D Beam/Slider
Parameter
Value
D Beam
D Beam Sens
0–127
Slider
Specifies how the sliders will operate.
DIRECT
Slider Mode
CATCH
Keyboard
Parameter
Value
Keyboard
Specifies the velocity transmitted when a key is played.
REAL
Keyboard Velocity
1–127
LIGHT
Keyboard Velocity
MEDIUM
Curve
HEAVY
Keyboard Velocity
-63–+63
Sens
Aftertouch Sens
0–100
84
Explanation
The higher the value you set for this
parameter, the more sensitive the D
Beam controller becomes.
When you move a slider, control data
indicating its position will always be
output.
When you move a slider, control data will
start being transmitted only when the
current value of the parameter has been
reached.
Explanation
The transmitted velocity value will
correspond to the force with which you strike
the key.
The transmitted velocity value will be fixed,
regardless of the force with which you strike
the key.
The keyboard will have a lighter-feeling
touch. Since you'll be able to reach fortissimo
(ff ) without having to play as strongly as
with the MEDIUM setting, the keyboard will
feel lighter. This setting makes it easier for
people with reduced finger strength to play
the keyboard.
This is the standard keyboard touch setting.
The key will have a heavier-feeling touch.
Since you'll need to play more strongly than
with the MEDIUM setting in order to reach
fortissimo (ff ), the keyboard will feel heavier.
This setting allows you to use your playing
dynamics to add more expression to your
performances.
This is a fine adjustment to the keyboard
sensitivity that's applied after the Keyboard
Velocity Curve setting. Higher values will
cause a greater velocity value to be transmit-
ted for a key-strike of the same force.
This specifies the aftertouch sensitiv-
ity. Higher values make it easier to apply
aftertouch. Normally, you can leave this set
at "100. "
Sound
Parameter
Value
Sound
Local Switch
OFF, ON
415.3–466.2
Master Tune
[Hz]
Master Key Shift
-24–+24
Master Level
0–127
Output Gain
-12–+12 [dB]
Song Level
0–127
Tone Remain
OFF, ON
Using the Local Switch setting
If you're using an external sequencer with the JUPITER-80's
keyboard controller section and sound generator section,
you should turn the Local Switch OFF. Here's why.
We need to connect these sections in the following order:
the JUPITER-80's keyboard
JUPITER-80's sound generator. Since the JUPITER-80's
keyboard section and sound generator section are connected
internally, such a connection order would normally be
impossible. However, if the Local Switch is OFF, the JUPITER-
80's keyboard section and its sound generator section will be
independent, allowing you to use an external sequencer as
shown here in the illustration.
Connections between the JUPITER-80 and the
external sequencer
JUPITER-80 Keyboard
(External) Sequencer
Explanation
Specifies whether the controller section
(keyboard, pitch bend/modulation lever,
[S1] [S2] buttons, D Beam controller, pedals,
etc.) will be connected to the internal sound
generator. Normally, this should be left at
"ON. " Turn it "OFF" if you want to use the
JUPITER-80's controllers only to control an
external sound generator.
Sets the JUPITER-80's overall tuning (the
frequency of the A4 key)
Shifts the JUPITER-80's overall pitch range in
semitone steps.
Sets the JUPITER-80's overall volume (except
for the signal from the USB COMPUTER
connector).
Adjusts the JUPITER-80's overall output
gain (except for the signal from the USB
COMPUTER connector). If you're playing a
fewer number of voices, boosting this setting
can help you obtain an optimal output level
when recording on an external device.
Sets the volume of the USB memory song
player.
Specifies whether the currently sounding
notes will remain (ON) or not (OFF) when you
select a different sound.
external sequencer
the
Local Off
JUPITER-80
Sound Generator
Advertisement
Table of Contents
