Table of Contents
Advertisement
→
14. OTHERS
14-1 Troubleshooting (Cont'd)
TROUBLES WITH ERROR CODE OUTPUTS
Error Code
Error Details
3200
Tape loading impossible.
Operation stops. All operations
are rejected.
3300
Tape unloading impossible.
Operation stops. All operations
are rejected.
4100
Irregular eject operation.
Operation stops. All operations
are rejected.
4200
Cassette housing abnormality.
Operation stops. All operations
are rejected.
5605
Tape is cut.
Operation stops. All operations
are rejected.
5606 to 5607
Tape is slack.
Operation stops. All operations
are rejected.
5702
Tape end sensor error.
Operation stops. All operations
are rejected.
5802
Tape beginning sensor error.
Operation stops. All operations
are rejected.
7001
Drum rotation stopped.
Operation stops. All operations
are rejected.
7101
Capstan rotation stopped.
Operation stops. All operations
are rejected.
7202 to 7203
Supply reel rotation error.
Operation stops. All operations
are rejected.
7302 to 7303
Take up reel rotation error.
Operation stops. All operations
are rejected.
7305
Irregular tape winding when
Operation stops. All operations
unloading.
are rejected.
E-90
For servicing
See the service manual page 1-26, "1.18 WARNING CODES".
GY-DV700W Operation
Remedy
Switch the power OFF and then
switch it back ON. However, the tape
may be damaged depending on the
situation. Please consult the person
in charge of professional video
equipment at your nearest JVC-
authorized service agent.
Open the cassette cover by using the
EJECT switch and then switch the
power ON again.
Switch the power OFF and then
switch it back ON. However, the tape
may be damaged depending on the
situation. Please consult the person
in charge of professional video
equipment at your nearest JVC-
authorized service agent.
14-1 Troubleshooting (Cont'd)
TROUBLES WITHOUT ERROR CODE OUTPUTS
Symptoms
• Is power supply connected properly?
Power cannot be switched ON.
• Is battery pack recharged?
• When the lithium battery is depleted, it may not be possible to turn on the power.
• Was the power turned ON immediately after being turned OFF?
Wait at least 5 seconds before turning the power ON again once it has been turned
OFF.
Operation buttons on the GY-DV700W
• Check whether the VCR Setup Menu item No. 050 REMOTE SELECT has been set
don't work.
to "IEEE1394" or "RS232C". If so, change the setting to "LOCAL".
• Is the cassette cover open?
The GY-DV700W remains inoperative as long as the cassette door is open.
Recording is not possible.
• Is switch on cassette set to REC? If it is set to SAVE, set it to REC.
• Video head may be clogged with dirt. Clean head with the special head cleaning
Noise interferes with playback video.
tape. (See page 7 and the separate sheet "Precautions for Use of Head Cleaning
Tape".)
Sound and picture are disturbed during
• Is the sync signal input to the SYNC IN connector disturbed? If so, check and
remedy the input sync signal.
playback.
Time code data is not shown as on-
• Time code data is not shown as on-screen-display during recording or playback.
screen-display.
The data is shown only on the counter display.
Time code and user's bit data are not
• Is the COUNTER switch set to "CTL"?
shown on the counter display.
Remaining battery power display is
• The VCR Setup Menu item No. 396 BATTERY TYPE may not be set correctly in
incorrect.
accordance with the type of battery in use. If the menu item setting is incorrect, set
it correctly using the VCR setup menu item BATTERY TYPE.
Battery alarm is displayed and the GY-
• Is the battery old?
DV700W enters the non-operating mode
even when a fully charged battery is used.
Cassette cannot be ejected after the
• The capacity of the power supply may be insufficient. Check the power voltage.
power is turned ON.
Viewfinder image looks dark or unclear.
• Adjust the viewfinder's contrast and bright controls.
• Is the filter turret set to 5600K+ND?
• Is the iris closed?
• Is the shutter speed too fast?
• Is the viewfinder cable correctly connected?
Noise appears when playing back a tape
• When a tape recorded on another unit is played back or used for recording, this
phenomenon may occur due to tracking errors.
recorded on another unit.
The transient section between scenes
recorded on other units and those
recorded on this unit may appear
disturbed.
The front section's recording level control
• Is the VCR Setup Menu item No. 246 FRONT VOLUME ENABLE set to "DISABLE".
doesn't work.
If so, set to "ENABLE".
The front section's recording level control
• The front section's recording level control cannot be used to change the recording
doesn't change the recording level of the
level of the sound input to CH2. Use the side section's CH2 recording level control
sound input to CH2.
for this purpose.
Recording operation stopped.
• Is the SERVO indicator or "SYNC INH" displayed on the counter display?
If so, check the input sync signal.
14. OTHERS
Remedy
If so, set the switch to "TC" or "UB".
E-91
Advertisement
Table of Contents
