Table of Contents
Advertisement
2. CONTROLS, INDICATORS AND CONNECTORS
2-6 Counter Display Contents
OPERATE/WARNING
LIGHT
CH 1
AUTO OFF DEW
OVER
RESET
ON
40 30
20
10
0 dB
CH 2
OVER
SERVO
RF
L i
OFF
32k
48k
SLAVE
PB
HOLD
AUD LOCK
SP
MONITOR
SELECT
WIDE
COUNTER
MENU
H
M
S
F
CTL
E
BATT
F
COUNTER
REMAIN
REV FWD
TC
UB
H
M
switch
Counter display
1.
Tape counter display
CTL
"CTL"
TC
CTL counter
UB
H
M
S
F
"TC"
CTL
"TC"
TC
Time code
UB
H
M
S
F
CTL
"UB"
User's bit
TC
VCR Setup
UB
Menu No. 516
DISPLAY SELECT
Hour Min
Sec
CTL
Time display
"TC"
TC
UB
H
M
S
"CLOCK"
CTL
"UB"
TC
Date display
UB
Day
Month
Year
2.
4.
VCR Setup Menu display
Error code display
3.
4.
Hour meter display
Alarm display
H
Remaining Tape Time Display
This display shows the remaining tape time (minutes/seconds)
in record and play modes.
• Example: 30 minutes of remaining tape.
REMAIN
H
M
• This indicator blinks when remaining tape time is equivalent
to less than 2 minutes.
* An alarm sounds as a warning when remaining tape time is
equivalent to less than 2 minutes in the record mode
REMAIN
H
M
• The following display appears when no videocassette is
loaded or during the calculation of remaining tape that takes
place immediately after a videocassette is inserted.
REMAIN
H
M
E-22
The counter display shows the following 4 types of information.
1.
Tape counter display
The counter display usually functions as a tape counter
(hour, minute, second, frame). It can be switched to a CTL
counter, time code or user's bit display by using the
COUNTER switch. (When the VCR Setup Menu item No.
516 DISPLAY SELECT is set to "TC".)
• CTL counter: Time between -9 hr. 59 min. 59 sec. 24
frames and 9 hr. 59 min. 59 sec. 24 frames
can be displayed.
* CTL counter indication may also corrupt
at playback of segment which time code
signal is not continuously recorded.
• Time code : Time between 0 hour and 23 hr. 59 min. 59
sec. 24 frames can be displayed.
• User's bit
: Hexadecimal number from 0 to F is displayed
in 8 digits.
When the VCR Setup Menu item No. 516 DISPLAY SELECT
is set to "CLOCK", the date and time are displayed. Set the
COUNTER switch to TC or UB.
TC: Time (Hour, Min., Sec.) is displayed.
UB: Date (Day, Month, Year) is displayed.
• Press the MENU button to switch to the VCR Setup Menu
setting display.
2.
VCR Setup Menu setting display
This display is used when setting the setup menus. After
setting of the setup menus, the tape counter display returns.
For details, see "DISPLAYING AND SETTING VCR SETUP
MENUS" on page 67.
3.
Hour meter display
The hour meter is displayed by selecting the HM group from
the VCR Setup Menu.
The hour meter data refers to the accumulated head drum
running time.
4.
Error code/Alarm display
The error code or alarm indicator is displayed automatically
in case an abnormal condition occurs with the unit.
See "TROUBLES WITH ERROR CODE OUTPUTS" on
page 90.
See "ALARM INDICATIONS" on page 86.
Remaining Battery Power Display
The 7-dot segment bar display shows the remaining battery
power. The lighted segment bars decrease as the remaining
battery power decreases.
• To display the remaining battery power accurately, set the
VCR Setup Menu item No. 396 BATTERY TYPE according
to the type of the battery pack in use.
E
BATT
F
All segment bars light when a fully charged
battery pack is attached.
The last 2 segment bars and "BATT" start
E BATT
to blink when the batter y is near ly
exhausted. Replace with a fully charged
battery pack.
When the battery capacity has run out, "E"
E BATT
and "BATT" blink and the unit stops
operation automatically.
2. CONTROLS, INDICATORS AND CONNECTORS
2-7 Lens (optional)
A19 × 8.7BW
5
4
3
2
1
A19x8.7BW
(A19x8.7BRRM-39)
1:1.8/8.7-165
mm
MADE IN JAPAN
QUICK Z
FUJIN0N
by
FUJI PHOTO OPTICAL CO., LTD.
M
or RET
A
W
T
6 7 8
9
0
!
C
@ #
$
%
^ &
FOCUS ring
1
Manual focus ring.
ZOOM lever/ring
2
This is the manual zoom ring equipped with a zoom lever. To
activate the zoom feature on, turn the zoom mode knob
12
position "M".
IRIS ring
3
Manual Iris ring. To activate the auto iris feature, set the Iris
Mode switch
to A.
10
Macro lever
4
Pull this lever up to enable the rotation of the macro ring.
Macro focusing ring (for close-up shooting)
5
By rotating this ring in the direction of the arrow, the lens be-
comes capable of close-up shooting of very small objects.
Normal focus adjustment and zooming are not available in the
macro mode.
To shoot images in the macro mode, set the focus ring to the
infinite position and the zoom ring to the widest angle position.
To adjust the focus of the macro image, rotate this ring in the
direction of arrow until the object is focused.
Note :
The back-focus knob is located close to the macro ring, be
careful not to mistake the back-focus knob for the macro ring.
After the required operation, be sure to return the macro ring
to the normal position.
BACK FOCUS ring/fixing screw
6
For Set-up Back Focus adjustment only.
Secure with the Screw knob after adjustment.
[VTR] trigger button
7
To start shooting push once.
To stop shooting push again.
[RET] return video button
8
The return video signal from the VCR section can be moni-
tored on the viewfinder only while pushing this button.
• The Viewfinder Status display is not available during this operation.
ZOOM servo control lever
9
Pushing this lever in the W direction makes the lens move
wider.
Pushing this lever in the T direction makes the lens move tighter.
Pushing harder changes the speed of the Zoom. To operate the
servo zoom feature with this lever, set the ZOOM knob
IRIS mode switch
10
A : Activates the auto iris feature.
M : Allows manual iris control.
Momentary auto iris button
11
When the IRIS MODE switch
is at M, pushing this button
10
activates the Auto Iris Function while it is held down only.
ZOOM mode knob
12
S : Servo Zoom mode. Allows operation by the Zoom Servo
Control lever
.
9
M : Manual Zoom mode. Allows zoom control by the Zoom
lever/ring
.
2
REMOTE FOCUS control connector
13
To connect with an optional focus servo unit.
ZOOM servo connector
14
Connect with an optional zoom servo unit.
Aspect ratio switching lever
15
Switches the aspect ratio between 4:3 and 16:9.
Note :
to
Make sure to switch the lever to the correct position.
Rapid zoom setting switch
16
Quickly sets the zoom to telescopic mode.
For the setting method, refer to the "OPERATION MANUAL"
for the lens.
IRIS speed adjusting control
17
Adjusts the iris operation speed.
Memo :
If the speed becomes too fast, hunting may occur.
To avoid the phenomena described above, perform
adjustment again.
to S.
12
E-23
Advertisement
Table of Contents
