Table of Contents
Advertisement
10. S.S.F. (Super Scene Finder) FUNCTION
10-3 Deleting S.S.F. Data
OPERATE/WARNING
LIGHT
RESET
ON
OFF
MONITOR
COUNTER
FILTER
SELECT
1 3200k
CTL
ALARM
TC
2 5600k+1/8ND
UB
3 5600k
4 5600k+1/64ND
SHUTTER
STATUS
MONITOR
C C
MENU
CH-1
AUDIO
CH-2
LEVEL
AUTO IRIS
FULL AUTO BLACK
LOLUX
BACK L
STRETCH
NORMAL
NORMAL
SPOT L
COMPRESS
NG
POWER
ON
OFF
NG button
10-4 Resetting S.S.F. Data
LOG
REW
STOP
FF
PLAY
STILL
2.
1.
LOG button
STOP button
OPERATE/WARNING
LIGHT
RESET
ON
OFF
MONITOR
FILTER
SELECT
COUNTER
CTL
1 3200k
ALARM
TC
2 5600k+1/8ND
UB
3 5600k
4 5600k+1/64ND
SHUTTER
STATUS
MONITOR
C C
MENU
CH-1
AUDIO
CH-2
LEVEL
AUTO IRIS
FULL AUTO BLACK
LOLUX
BACK L
STRETCH
NORMAL
NORMAL
SPOT L
COMPRESS
NG
POWER
ON
OFF
2.
RESET button
E-62
The S.S.F. data recorded in the unit's memory can be deleted
in the record mode and the record-pause mode.
This function is only valid in the MARK mode.
In the record mode, press the NG button after the IN point or
OUT point has been stored.
• When pressed after the IN point has been stored, the S.S.F.
data of the scene being recorded are deleted. When
pressed after the OUT point has been stored, the S.S.F.
data of the immediately preceding scene are deleted.
When the NG button is used for deleting operation, the
next scene number is updated to a new number.
In the record-pause mode, press the NG button.
The S.S.F. data of the immediately preceding scene are
deleted.
Note:
The NG button is only valid for the immediately preceding
scene. The erase of scene data by the NG button cannot
be confirmed on the unit.
Operation
1.
Press the STOP button to enter the stop mode.
2.
Press the RESET button while the LOG button is kept
pressed.
• All the S.S.F. data held in the memory are erased.
However, the reel number is not cleared.
10. S.S.F. (Super Scene Finder) FUNCTION
10-5 Writing S.S.F. Data to Tape
LOG
REW
STOP
FF
PLAY
STILL
1.
STOP button
2.
2.
LOG button
REW button
OPERATE/WARNING
LIGHT
RESET
ON
OFF
MONITOR
FILTER
SELECT
COUNTER
CTL
1 3200k
ALARM
TC
2 5600k+1/8ND
UB
3 5600k
4 5600k+1/64ND
SHUTTER
STATUS
MONITOR
C C
MENU
CH-1
AUDIO
CH-2
LEVEL
AUTO IRIS
FULL AUTO BLACK
LOLUX
BACK L
STRETCH
NORMAL
NORMAL
SPOT L
COMPRESS
NG
POWER
ON
OFF
CH-1
AUDIO
CH-2
TC GENERATOR
LEVEL
CH-1
CH-2
AUTO
PRESET
FREE
MANUAL
REGEN
REC
AUDIO SELECT
AUDIO INPUT
CH-1
CH-2
CONTINUE
MENU
FRONT
REAR
LITHIUM BATT.
GROUP
ITEM
SELECT
DATA SET
HOLD
SHIFT
ADVANCE
PRESET
CONTINUE button
10-6 Outputting S.S.F. Data
The S.S.F. data in the memory of the main unit or that recorded
at the beginning of the tape can be output via the VTR REMOTE
connector using the RS-232C controller.
For how to make connections for this, refer to "Connecting to a
PC" on page 65.
Operation
In the stopped condition, the GY-DV700W answers with the
S.S.F. data when it receives the RS-232C command D5h "S.S.F.
DATA SENSE" from the PC.
(Indication example)
START
ID NO: 2c97
REEL NO: 1818
SCENE
MARK IN
MARK OUT
CUE
001M
00:00:00:16
00:00:04:19
002M
00:00:06:03
00:00:08:08
003C
00:03:15:17
00:03:57:00
004C
00:03:58:18
00:05:37:24
00:04:00:21
004C
00:03:58:18
00:05:37:24
00:04:07:22
004C
00:03:58:18
00:05:37:24
00:04:18:23
END
S.S.F. data stored in the unitís memory can be written to the
beginning of tape.
Precautions when writing S.S.F. data
• When S.S.F. data stored in the memory of the GY-
DV700W is written to the beginning of the rewound tape,
approximately 5 seconds of recorded video and/or sound
will be erased at the beginning.
In the case of important recordings, leave 5 seconds or
more of the tape unrecorded before starting recording.
• Writing of S.S.F. data should be done with the DC cable
disconnected.
Operation
1.
Press the STOP button to enter the stop mode.
2.
Press the REW button while the LOG button is kept pressed.
• The REW indicator blinks during tape transport in the
writing position.
• The LOG indicator lights while S.S.F. data are being
written to the tape.
• When writing to the tape is completed, the LOG indicator
goes out.
About the Scene End Cue Up Function
When the CONTINUE button is pressed while the LOG
button is kept pressed in the stop mode, the tape winds
to the S.S.F. data's last OUT point, after which the unit
enters the record-pause mode. (Scene End Cue Up)
The FF button's LED blinks during the Scene End Cue
Up mode.
Note:
Once a tape with recorded S.S.F. data is ejected and then
reinserted again, the previous data will be erased if new
S.S.F. data are recorded on the tape.
Operation
When recording in the S.S.F. mode is completed, and the
cassette tape has not been taken out, the S.S.F. data stored
in the memory of the GY-DV700W are output when the RS-
232C command D5h is received.
If the tape recorded in S.S.F. mode is ejected and then loaded
again, the GY-DV700W rewinds the tape to the beginning
and plays back for about 10 seconds when it receives the
RS-232C command D5h.
During the playback, the model lD data and reel number
recorded on the tape are read. If corresponding S.S.F. data
are found in the memory, these data are output.
If corresponding S.S.F. data are not found in the memory, the
tape is rewound to the beginning once more, and after about
20 seconds of slow playback the stop mode is entered.
During slow playback, if S.S.F. data are written at the
beginning of the tape, these data are read out, and after the
stop mode is entered the S.S.F. data are output.
∗ If S.S.F. data does not exist, the 05h (NOT TARGET)
command is output.
E-63
Advertisement
Table of Contents
