General Safety Rules - RIDGID R2610 Operator's Manual

GENERAL SAFETY RULES

WARNING:
Read and understand all instructions. Failure to
follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
Work Area
■ Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
■ Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable liq-
uids, gases, or dust. Power tools may create sparks
which may ignite the dust or fumes.
■ Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
Electrical Safety
■ Double insulated tools are equipped with a polar-
ized plug (one blade is wider than the other). This
plug will fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician
to install a polarized outlet. Do not change the plug
in any way. Double insulation
for the three-wire grounded power cord and grounded
power supply system.
■ Avoid body contact with grounded surfaces, such
as pipes, radiators, ranges, and refrigerators. There
is an increased risk of electric shock if your body is
grounded.
■ Don't expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of elec-
tric shock.
■ Do not abuse the cord. Never use the cord to carry
the tools or pull the plug from an outlet. Keep cord
away from heat, oil, sharp edges, or moving parts.
Replace damaged cords immediately.
■ When operating a power tool outside, use an out-
door extension cord marked "W-A" or "W". These
cords are rated for outdoor use and reduce the risk of
electric shock.
■ Damaged cords increase the risk of electric shock.
Personal Safety
■ Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not
use tool while tired or under the influence of drugs,
alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal
injury.
■ Dress properly. Do not wear loose clothing or jew-
■ Avoid accidental starting. Be sure switch is off be-
■ Remove adjusting keys or wrenches before turn-
■ Do not overreach. Keep proper footing and balance
■ Use safety equipment. Always wear eye protection.
■ Do not use on a ladder or unstable support.
■ Loose clothes, jewelry, or long hair can be drawn
Tool Use and Care
■ Use clamps or other practical way to secure and
eliminates the need
■ Do not force tool. Use the correct tool for your ap-
■ Do not use tool if switch does not turn it on or off.
■ Disconnect the plug from power source before mak-
■ Store idle tools out of the reach of children and other
■ Maintain tools with care. Keep cutting tools sharp
■ Check for misalignment or binding of moving parts,
■ Use only accessories that are recommended by the
3
elry. Contain long hair. Keep your hair, clothing, and
gloves away from moving parts. Loose clothes, jew-
elry, or long hair can be caught in moving parts.
fore plugging in. Carrying tools with your finger on the
switch or plugging in tools that have the switch on, in-
vites accidents.
ing the tool on. A wrench or a key that is left attached
to a rotating part of the tool may result in personal in-
jury.
at all times. Proper footing and balance enables better
control of the tool in unexpected situations.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
into air vents.
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
plication. The correct tool will do the job better and
safer at the rate for which it is designed.
Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
ing any adjustments, changing accessories, or stor-
ing the tool. Such preventive safety measures reduce
the risk of starting the tool accidentally.
untrained persons. Tools are dangerous in the hands
of untrained users.
and clean. Properly maintained tools with sharp cut-
ting edges are less likely to bind and are easier to con-
trol.
breakage of parts, and any other condition that may
affect the tool's operation. If damaged, have the tool
serviced before using. Many accidents are caused
by poorly maintained tools.
manufacturer for your model. Accessories that may
be suitable for one tool, may become hazardous when
used on another tool.