Your belt sander has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
GENERAL SAFETY RULES WARNING: Read all instructions Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
GENERAL SAFETY RULES SERVICE Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. WARNING! To reduce risk of injury, user must read instruction manual.
SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer. SYMBOL NAME Volts Amperes Hertz Watt Minutes Alternating Current Direct Current...
To avoid serious personal injury, do not attempt to use this product until you read thoroughly and understand completely the operator’s manual. If you do not understand the warnings and instructions in the operator’s manual, do not use this product. Call RIDGID assistance. customer service for ®...
ELECTRICAL DOUBLE INSULATION Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded.
FEATURES PRODUCT SPECIFICATIONS Belt Size ...3 in. x 18 in. Sanding Surface ... 17.5 sq. in. No Load Speed ... 400 - 950 ft./min. TRACKING SCREW DUST REAR HANDLE DRIVE ROLLER Input ...10 V, 60 Hz, AC only, 6.5 Amps Net Weight ...
BELT TENSION RELEASE LEVER The tension release lever aids in quick and easy belt changes. DUST BAG The dust bag attaches to the sander and keeps dust to a minimum. ERGONOMIC DESIGN The design provides for easy handling. It is designed for comfort and ease of operation in different positions and at different angles.
Finally, use finer grit for finishing the surface. Always continue sanding with each grit until the surface is uniform. SETTING THE BELT SANDER SPEED Refer to the chart below for belt sander speed selections. SPEED ...
Page 11
WARNING: Do not let your fingers rest over the front or right edge of the sander. If the sanding belt were to run off, or if it were not properly adjusted, your fingers could come in contact with the moving sanding belt resulting in possible serious injury.
Page 12
If the sanding belt is not a bidirectional belt, ensure that the arrow inside the belt is pointing in the direction of the rotation (clockwise when looking into the open side of the sander). Installing unidirectional sanding belts backwards can create a hazardous condition.
Page 13
Using the rear handle to control the sander and the front handle only to guide it, move it slowly over the work. Allowing the sander to remain in one place will result in an uneven surface. WARNING: Keep a firm grip on sander with both hands at all times.
Page 14
The dust bag provides a dust collection system for the sander. It should be installed over the exhaust hole located on the side of the sander. For more efficient operation, empty dust bag when half full. Do not connect sander to power supply before installing dust bag.
Connect the sander to power supply. Set the variable speed control dial to the lowest setting (A). With sander positioned as shown below, pull switch trigger. NOTE: This position is for adjustments only. Sanding belt should not be in contact with workpiece or any foreign objects when making belt tracking adjustments.
MAINTENANCE WARNING: When servicing use only identical RIDGID replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust.
Page 17
See Figure 13 . Unplug the sander. Remove dust bag. Remove sanding belt from sander. Follow instructions on page 1 to remove sanding belt. NOTE: Removing sanding belt will simplify the process of installing a new timing belt.
/1/04 and after. This product is manufactured by One World Technologies, Inc. The trademark is licensed from RIDGID, Inc. All warranty communications should be directed to One World Technologies, Inc., attn: RIDGID Hand Held and Stationary Power Tool Technical Service at (toll free) 1-866-539-1710.
Page 20
R2740 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgid.com.