Casio 2362 Manual

Module No. 2362
• Button operations are indicated using the letters shown in the illustration.
• Each section of this manual provides you with the information you need to perform operations in each mode. Further details and technical information can
be found in the "REFERENCE" section.
• Press C to change from mode to mode.
• In any mode, press B to illuminate the display for about two seconds.
Timekeeping Mode
Press C.
TIMEKEEPING
Use the Timekeeping Mode to set and view the current time and date. You can also
display the Last Signal screen in the Timekeeping Mode.
Last Signal
Receive indicator
Receive date
Press D.
Receive time
• The Last Signal screen alternate between the time and date that the time calibration
signal was successfully received.
Current Time Setting
Normally, you do not need to do anything to set the current time as long as you are
within an area in West Europe where the watch can pick up the time calibration signal.
You can also set the current time manually when you are outside the range of the
signal.
• Before using the watch after purchasing it, use the procedure under "Selecting Your
Home City Code" to specify your home city, and then use the procedure under "To
perform manual time calibration signal reception."
• Note that after you set your Home City code, you must also turn on the watch's time
calibration signal receiver if you want to enable auto time calibration. See "About
Auto Receive" for more information.
• See "Setting the Digital Time and Date Manually" for information about manual
settings.
• The analog time of this watch is synchronized with the digital time. Because of this,
the analog time setting is automatically adjusted whenever you change the digital
setting. See "Analog Timekeeping" for more information.
Setting the Digital Time and Date Manually
Once you select a Home City code and set its time, you can view the current time in
other cities by simply changing the city code setting. Even if you plan to use the watch
without enabling auto time calibration, be sure to select a Home City code (the city
code whose time and date you are setting), before you set the time and date.
To set the current digital time and date manually
1. In the Timekeeping Mode, hold down A until the
current Auto Receive On/Off setting starts to flash,
which indicates the setting screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Auto
DST
Receive
Day Month
Day Counter Mode
Date
Hour : Minutes
Month – Day
Press A.
PM indicator
Day of week
12/24-Hour
City Code Seconds
Format
Year Minutes
ABOUT THIS MANUAL
GENERAL GUIDE
Telememo Mode
3. When the setting you want to change is flashing, use B and/or D to change it as
described below.
Setting
Auto Receive
Time
DST
12/24-Hour format
City Code
Seconds
Seconds
Hour, Minutes, Year,
Month, Day
• Auto Receive setting is used for time calibration signal reception only. See "About
Auto Receive" for details.
• See "CITY CODE TABLE" at the back of this manual for a complete list of
available codes.
• Daylight Saving Time (DST) advances the time setting by one hour from Standard
Time. Remember that not all countries or even local areas use Daylight Saving
Time.
4. Press A to exit the setting screen.
Selecting Your Home City Code
You can select a city code for your Home City (the city where you normally use the
watch). This data can be changed any time you move to another geographic area.
• See "CITY CODE TABLE" at the back of this manual for a complete list of available
codes.
• Once you select a Home City code and set its time, you can use World Time to view
the current time in any one of 28 cities (29 time zones) around the world by simply
specifying a city code.
To select your Home City code
City code
Time Calibration Signal Reception
This watch is designed to pick up a time calibration signal transmitted from
Mainflingen, Germany and update its time setting in accordance with the signal. There
are two different methods you can use to receive the signal: Auto Receive and
Manual Receive. With Auto Receive, the watch automatically receives the calibration
signal three times each day and makes appropriate adjustments. With Manual
Receive, you perform a specific button operation to receive the calibration signal.
Hour
Alarm Mode
Hand Setting Mode
Screen Button Operations
Press D to toggle auto receive on and off.
Press D to toggle between Daylight Saving
Time (ON) and standard time (OFF).
Press D to toggle between 12-hour (12H)
and 24-hour (24H) timekeeping.
Use D (+) and B (–) to change the
setting.
Press D to reset to 00.
Use D (+) and B (–) to change the
setting.
1. In the Timekeeping Mode, hold down A until the
current Auto Receive On/Off setting starts to flash,
which indicates the setting screen.
2. Press C three times to move the flashing to the City
Code setting.
3. Use D (+) and B (–) to change it.
4. Press A to exit the setting screen.
2362-1
Stopwatch Mode