Zanussi ZGF 786 ICX Operating And Installation Manual
  1. Manuals
  2. Brands
  3. Zanussi Manuals
  4. Hob
  5. ZGF 786 ICX
  6. Operating and installation manual
Zanussi ZGF 786 ICX Operating And Installation Manual

Zanussi ZGF 786 ICX Operating And Installation Manual

Hide thumbs Also See for ZGF 786 ICX:
Table of Contents

Advertisement

Quick Links

Download this manual
GAS HOBS
(ZGF 786 ICX)
(ZGF 786 ICW)
OPERATING AND INSTALLATION MANUAL
1

Advertisement

Table of Contents
loading

Related Manuals for Zanussi ZGF 786 ICX

Summary of Contents for Zanussi ZGF 786 ICX

  • Page 1 GAS HOBS (ZGF 786 ICX) (ZGF 786 ICW) OPERATING AND INSTALLATION MANUAL...

  • Page 2: For Your Safety

    Repairs carried out by installing a cooker hood with discharge tube. unexperienced persons may cause injury or serious malfunctioning. Refer to your local Zanussi Service • In case of intensive or long time use of the Centre. Always insist on genuine Zanussi spare appliance, make the ventilation more efficient, parts.

  • Page 3: Table Of Contents

    Contents For Your Safety ..........2 5. Technical Data ..........6 1. Instruction for the User ........ 3 6. Instruction for the Installer ......7 2. Cleaning and Maintenance ......4 7. Electrical Connection ........8 3. Periodic Maintenance ........6 8.

  • Page 4: Cleaning And Maintenance

    THE HOB LID Always clean the lid from cooking residues before In order to make the appliance match with the kitchen opening it or taking it off. design, a lid (not provided) can be fitted on the hob. WARNING! The crystal lid can splinter when The lid is meant to avoid dust to settle on the hob, overheated.
  • Page 5 Enamelled pan supports In hobs provided with enamelled pan supports, these can be removed and kept in the right position thanks to special hinges in the back of the hob (see fig. 4 and 5). This solution enables rapid and easy cleaning of the hob.

  • Page 6: Periodic Maintenance

    3. Periodic Maintenance Periodically ask your local Service Centre to check the The periodic lubrication of the taps must be conditions of the gas supply pipe and the pressure carried out by qualified personnel, which you adjuster, if fitted. must refer to also in case of malfunctioning. To ensure the good operation of the hob and its safety features, it is necessary that the taps are periodically lubricated.

  • Page 7: Instruction For The Installer

    6. Instruction for the Installer The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top.

  • Page 8: Electrical Connection

    7. Electrical Connection The appliance is designed to be connected to 230 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force. Before the appliance is connected: 1) check that the main fuse and the domestic installation can support the load (see the rating label);...

  • Page 9: Adaptation To Different Types Of Gas

    8. Adaptation to different types of gas REPLACEMENT OF INJECTORS • Remove the pan supports. • Remove the burner's caps and crowns. • With a socket spanner 7 unscrew and remove the injectors (Fig. 10), and replace them with the ones required for the type of gas in use (see table on the next page).

  • Page 10: Building In

    BURNERS TYPE TYPE OF INJECTORS NOMINAL REDUCED NOMINAL NOMINAL OF GAS BURNER MARKS POWER POWER POWER PRESSURE 1/100 mm INPUT mbar Ultra-rapid (large) 0,323 NATURAL Rapid (large) 0,65 0,276 Semi-rapid (medium) 0,45 0,180 G 20 Auxiliary (small) 0,33 0,104 Ultra-rapid (large) Rapido (grande) 0,65 Buthane...
  • Page 11 FITTING THE LID We recommend the lid hinge block are fitted before installing the hob into the worktop. To install the lid onto the hob, proceed as follows: a. Remove the right and left hand grid blocks fitted to the back of the hob, by unscrewing the relevant screws (fig.

  • Page 12: Screws (Fig

    INSTALLATION AND ASSEMBLY These hobs can be installed in a kitchen unit with an opening for insertion whose dimensions are shown in Fig. 16. The edge of the cut out must have a minimum distance from the rear wall of 55 mm. If there are side walls, or sides of the furniture unit near the hob, the cut out edges must have a minimum distance of 150 mm.
  • Page 13 POSSIBILITIES FOR Fig. 20 Fig. 19 INSERTION Kitchen unit with door Proper arrangements must be taken in designing the forniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in Fig.

Table of Contents