Table of Contents
Advertisement
When
is selected, a full-
LARGE
range output will be sent to the
front left and right outputs, and
NO low-frequency signals will be
sent to the subwoofer output.
5. When you have completed your
selection for the front channel, press
the
button
, and then
i ˜
Set
press the
buttons
g
⁄
¤
/
remote or the
Selector
on the front panel to change the dis-
play to
CEN SPEAKER
6. Press the
button
i ˜
Set
and use the
buttons
⁄
¤
/
the remote, or the
Selector
on the front panel, to select the
¸
option that best describes your system
based on the speaker definitions
shown above.
When
CEN SP SMALL
selected, low-frequency center
channel sounds will be sent to the
subwoofer output only. Note that if
you choose this option and there is
no subwoofer connected, you will
not hear any low-frequency sounds
from the center channel speaker.
When
CEN SP LARGE
selected, a full-range output will be
sent to the center speaker output,
and NO center channel signal will
be sent to the subwoofer output.
System Configuration
When
no signals will be sent to the center
channel output. The receiver will
operate in a "phantom" center
channel mode and center channel
information will be sent to the left
and right front channel outputs.
7. When you have completed your
on the
selection for the center channel, press
buttons
the
¸
Set
press the
.
remote or the
on the front panel to change the
again,
display to
on
g
buttons
8. Press the
and then use the
on the remote or the
buttons
select the option that best describes
your system based on the speaker
is
definitions shown above.
When
selected, low-frequency surround
channel sounds will be sent to the
subwoofer output only. Note that if
you choose this option and there is
no subwoofer connected, you will
not hear any low-frequency sounds
is
from the surround speaker.
When
a full-range output will be sent to the
surround channel outputs, and NO
surround channel signals will be sent
to the subwoofer output.
18
is selected,
CEN SP NONE
button
, and then
i ˜
buttons
on the
g
⁄
¤
/
buttons
¸
Selector
.
SUR SPEAKER
button
again,
i ˜
Set
buttons
g
⁄
¤
/
Selector
on the front panel to
¸
is
SUR SP SMALL
is selected,
SUR SP LARGE
When
SUR SP NONE
surround sound information will be
split between the front left and front
right outputs. Note that for optimal
performance when no surround
speakers are in use, the Dolby 3
Stereo mode should be used instead
of Dolby Pro Logic.
9. When you have completed your
selection for the surround channel,
press the
button
i ˜
Set
then press the
buttons
⁄
¤
/
the remote or the
Selector
on the front panel to change the display
to
.
S W SPEAKER
10. Press the
button
i ˜
Set
then press the
buttons
⁄
¤
/
the remote or the
Selector
on the front panel to select the option
that best describes your system.
Select
if a subwoofer
S-W SP ON
is connected to your system.
Select
S-W SP OFF
NOT connected to your system. Note
that when no subwoofer is selected,
low-frequency sounds below 100Hz
will be sent to the front left/right
speakers, provided that the selection
in step 4, above, has been set to
. Otherwise, no low-frequency
LARGE
sounds will be heard. This option is
not available when the front, center or
surround speakers are set to
is selected,
, and
on
g
buttons
¸
, and
on
g
buttons
¸
if a subwoofer is
.
SMALL
Hide quick links:
Advertisement
Table of Contents
