Central Pneumatic Contractor 90399 Assembly And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Central Pneumatic Manuals
  4. Power Tool
  5. Contractor 90399
  6. Assembly and operating instructions manual

Central Pneumatic Contractor 90399 Assembly And Operating Instructions Manual

Contractor series floor stapler with hammer and case
Hide thumbs
Table of Contents

Advertisement

Quick Links

FLOOR STAPLER
WITH HAMMER AND CASE
ASSEMBLY and OPERATING
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
©
Copyright
2003 by Harbor Freight Tools
this manual or any artwork contained herein may be reproduced in any shape or
form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Model 90399
INSTRUCTIONS
Revised Manual 06/04
®
®
. All rights reserved. No portion of
®

Advertisement

Table of Contents
loading

Related Manuals for Central Pneumatic Contractor 90399

Summary of Contents for Central Pneumatic Contractor 90399

  • Page 1 Copyright 2003 by Harbor Freight Tools this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353 INSTRUCTIONS ®...

  • Page 2: Specifications

    Staples included: 400, 1/2” crown, 2” Long, 15 Gauge Iincludeds: Tool Oil, 3 Hex Wrenches, Storage Case, Hammer Note: SKU 90429 - 2”, 15 Gauge Staples are available from Harbor Freight Tools. Note: This Floor Stapler is designed for use on wood floors.
  • Page 3 Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. Do not operate tool if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs.

  • Page 4: Operation

    (California Health & Safety Code § 25249.5, et seq. ) When unpacking, check to make sure the parts listed on page 8 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible 1/4”-18 NPT...
  • Page 5 Pin (38) is pressed. While holding the Sleeve (36a) firmly, use a small screwdriver to press in the Locking Pin (38) along the edge of the Magazine Cover. See FIGURE 2. Locking Pin (38) Sleeve (36a) Magazine Cover (33a) SKU 90399 For technical questions, please call 1-800-444-3353. Operation (continued) FIGURE 1 Clamp Screws (44)

  • Page 6: Troubleshooting

    Air leaking in nose Lack of Power, slow to cycle. Intermittent feeding or no fastener coming out Jammed Staple SKU 90399 For technical questions, please call 1-800-444-3353. Operation (continued) Troubleshooting CAUSE SOLUTION 1. Loose Nose Screws 1. Tighten and recheck 2.

  • Page 7: Clearing Jams

    TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 90399 For technical questions, please call 1-800-444-3353. Clearing Jams...

  • Page 8: Parts List

    NOTE: #27a - Spacer for 1/2” Flooring (Included but not installed) NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. SKU 90399 For technical questions, please call 1-800-444-3353. Parts List l l o "...

  • Page 9: Assembly Diagram

    Assembly Diagram #27 - Installed: (Spacer for 25/32” Flooring) #27a - Spacer is included with tool, not installed (Spacer for 1/2” Flooring) REV 04/05; 02/06 SKU 90399 For technical questions, please call 1-800-444-3353. Page 9...

Table of Contents