1. Manuals
  2. Brands
  3. Central Pneumatic Manuals
  4. Nail Gun
  5. Contractor 97520
  6. Assembly and operating instructions manual

Central Pneumatic 97520 Assembly And Operating Instructions Manual

Air brad finish nailer 16 gauge - 2” contractor series
Hide thumbs Also See for 97520:
Table of Contents

Advertisement

Quick Links

AIR BRAD FINISH NAILER
ASSEMBLY AND OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
©
Copyright
2007 by Harbor Freight Tools
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
16 GAUGE - 2"
Model
3491 Mission Oaks Blvd., Camarillo, CA 93011
97520
94481
®
. All rights reserved. No portion of this
REV 08g
®
.

Advertisement

Table of Contents
loading

Related Manuals for Central Pneumatic 97520

Summary of Contents for Central Pneumatic 97520

  • Page 1 2007 by Harbor Freight Tools manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions or replacement parts, please call 1-800-444-3353. 16 GAUGE - 2”...

  • Page 2: Product Specifications

    Fastener Size Capacity Magazine Capacity Load Style Nose Piece Design Maximum Air Pressure Average Air Flow Air Inlet Size Trigger Mechanism Accessories Overall Dimensions Unit Weight You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual.
  • Page 3 Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically non-conductive clothes and non-skid foot- wear are recommended when working. Wear restrictive hair covering to contain long hair. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines or air hoses.
  • Page 4 Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. Do not operate tool if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs.
  • Page 5 When unpacking, check to make sure that the product is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.

  • Page 6: Operation

    For best service, you should incorporate a regulator and an in-line filter and oiler as shown in the diagram below. Hoses, couplers, regulators, filters, and oilers are all available from Harbor Freight Tools. AIR BRAD FINISH NAILER TESTING THE FULL SEQUENTIAL SAFETY TRIP MECHANISM WARNING: Even though the Nailer should be empty during this procedure, ALWAYS point the Nailer at a piece of scrap wood when testing.

  • Page 7: Loading Brads

    Connect the air supply to the tool at the Quick Connector (83). Set the regulator at the recommended 70 to 120 operating PSI. Do not exceed the maximum 120 PSI. Test the tool by depressing the Safety (50A) against the workpiece without pulling the Trigger (36).

  • Page 8: Operating The Nailer

    While holding the Pusher (63) in place, press the Release (74) and slide the Pusher forward. Attach the Nailer to the air supply at the Quick Coupler (83). Start your compressor and check the pressure, making sure it is set at the recommended 70-120 PSI.

  • Page 9: Clearing Jams

    Anytime any maintenance or repairs are done (including clearing jams), FIRST: Disconnect the Nailer from its air supply. Empty the Magazine Assembly (70) completely. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconected and is incapable of firing any Brads.

  • Page 10: Inspection, Maintenance, And Cleaning

    INSPECTION, MAINTENANCE, AND CLEANING Anytime any maintenance or repairs are done, FIRST: Disconnect the Nailer from its air supply. Empty the Magazine Assembly (70) completely. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any Brads.

  • Page 11: Please Read The Following Carefully

    PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.

  • Page 12: Assembly Diagram

    ASSEMBLY DIAGRAM For technical questions, please call 1-800-444-3353 SKU 94481 PAGE 12...
  • Page 13 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.

This manual is also suitable for:

94481

Table of Contents