Table of Contents
Advertisement
Quick Links
GB
ORIGINAL INSTRUCTIONS
F
NOTICE ORIGINALE
D
ORIGINALBETRIEBSANLEITUNG
NL
ORIGINELE GEBRUIKSAANWIJZING
S
BRUKSANVISNING I ORIGINAL
DK
ORIGINAL BRUGSANVISNING
N
ORIGINAL BRUKSANVISNING
FIN
ALKUPERÄISET OHJEET
E
MANUAL ORIGINAL
P
MANUAL ORIGINAL
I
ISTRUZIONI ORIGINALI
H
EREDETI HASZNÁLATI UTASÍTÁS
CZ
PŮVODNÍM NÁVODEM K POUŽÍVÁNÍ
TR
ORİJİNAL İŞLETME TALİMATI
PL
INSTRUKCJA ORYGINALNA
RU
ПОДЛИННИК РУКОВОДСТВА
ПО ЭКСПЛУАТАЦИИ
SKIL Europe BV - Konijnenberg 60
4825 BD Breda - The Netherlands
16
UA
GB
20
F
GR
26
D
RO
32
NL
38
S
BG
43
DK
SK
48
N
HR
53
FIN
SRB
58
E
SLO
64
P
EST
69
I
LV
75
H
LT
80
CZ
AR
85
TR
FA
91
PL
RU
97
www.skilmasters.com
SLIDING MITRE SAW
3855 (F0153855..)
UA
ОРИГІНАЛЬНА ІНСТРУКЦІЯ
З ЕКСПЛУАТАЦІЇ
GR
ΠΡΩΤΟΤΥΠΟ Ο∆ΗΓΙΩΝ ΧΡΗΣΗΣ
RO
INSTRUCŢIUNI DE FOLOSIRE
ORIGINALE
BG
ОРИГИНАЛНО РЪКОВОДСТВО
ЗА ЕКСПЛОАТАЦИЯ
SK
PÔVODNÝ NÁVOD NA POUŽITIE
HR
ORIGINALNE UPUTE ZA RAD
SRB
ORIGINALNO UPUTSTVO ZA RAD
SLO
IZVIRNA NAVODILA
EST
ALGUPÄRANE KASUTUSJUHEND
LV
ORIĢINĀLĀ LIETOŠANAS PAMĀCĪBA
LT
ORIGINALI INSTRUKCIJA
AR
FA
11/10
103
109
115
121
127
132
137
142
147
153
158
AR
173
AR
169
FA
FA
2610Z00731
Advertisement
Table of Contents
Related Manuals for Skil Masters 3855
Summary of Contents for Skil Masters 3855
- Page 1 ALGUPÄRANE KASUTUSJUHEND ISTRUZIONI ORIGINALI ORIĢINĀLĀ LIETOŠANAS PAMĀCĪBA EREDETI HASZNÁLATI UTASÍTÁS ORIGINALI INSTRUKCIJA PŮVODNÍM NÁVODEM K POUŽÍVÁNÍ ORİJİNAL İŞLETME TALİMATI INSTRUKCJA ORYGINALNA ПОДЛИННИК РУКОВОДСТВА ПО ЭКСПЛУАТАЦИИ www.skilmasters.com SKIL Europe BV - Konijnenberg 60 11/10 2610Z00731 4825 BD Breda - The Netherlands...
- Page 2 3855 1500 EPTA 01/2003 Watt 14,4 kg 5000 /min RUBBER 0° 0° 45° 45° 45° 0° MAX mm 45° 0° MAX mm MAX mm MAX mm 216 mm 216 mm MAX. MIN. 30 mm 30 mm 1,4 - 2,2 mm...
- Page 3 P1 Q1...
- Page 4 90º...
- Page 5 NOT INCLUDED NOT INCLUDED...
- Page 6 ø 35 mm...
- Page 7 0° 45° 45° 45° 0° Max A x Max B 0° 0° 65 x 305 mm 0° 0° 45° 0° 30 x 305 mm 45° 0° 0° 45° 65 x 215 mm 0° 45° 45° 45° 30 x 215 mm 45°...
- Page 8 0º 45º 0º 45º 45º 45º 0º...
- Page 9 CLASS 2 LASER LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT P max < 1mW, λ=650nm IEC/EN 60825-1: 2007...
- Page 10 & &...
- Page 12 ¡ 360º...
- Page 13 ™ £ 0º NOT INCLUDED 4 mm NOT INCLUDED...
- Page 14 ≤ 45º NOT INCLUDED 4 mm NOT INCLUDED ∞...
- Page 15 § ≥ •...
-
Page 16: Technical Specifications
Power tools create sparks which • Only use the tool when correctly and completely may ignite the dust or fumes. assembled (be aware that Skil cannot be hold c) Keep children and bystanders away while operating responsible for tool damage and/or personal injuries a power tool. -
Page 17: Outdoor Use
d) Remove any adjusting key or wrench before turning • Inrush currents cause short-time voltage drops; under the power tool on. A wrench or a key left attached to a unfavourable power supply conditions, other equipment rotating part of the power tool may result in personal injury. may be affected (if the system impedance of the power supply is lower than 0,295 + j0,184 Ohm, disturbances e) Do not overreach. -
Page 18: During Use
• SKIL can assure flawless functioning of the tool only For securing the tool (transport position) when the correct accessories are used which can be - slide the tool arm to the stop in the direction of fence obtained from your SKIL dealer L and tighten locking knob R •... - Page 19 • Compound cuts $ - saw this and the other workpieces to the same length - compound cuts require both a mitre angle setting and • Changing saw blade ¡ a bevel angle setting ! disconnect the plug - take hex key W from storage W1 ! always test out first on a piece of scrap material - set tool into working position •...
-
Page 20: Declaration Of Conformity
• If the tool should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service centre for SKIL power tools Scie à onglets radiale...