Maintenance & Service - Skil 8003 Instructions Manual

• Removing stickers (use fl at nozzle G) 0
- many adhesives become softer when heated,
allowing adhesive bonds to be separated and
superfl uous adhesive to be removed
! heat sticker on the upper side
! always take care not to overheat the underlying
surface
OTHER APPLICATION EXAMPLES:
★ removing linoleum and vinyl carpeting
★ removing carpet tiles made of synthetic fi bres
★ removing veneers/applying veneer strips
★ softening/melting tar, tin, bitumen, wax (use fl at
nozzle G)
★ waxing (skis, furniture) (use fl at nozzle G) !
★ removing resin
★ loosening rusty/too tightly fastened metal screws,
nuts and bolts
★ removing candle wax (do not overheat the
underlying surface)
★ repairing broken candles/restoring bent candles to
their original shape
• Shrink fi tting @
- use refl ector nozzle H or reduction nozzle J
- select a shrink-fi t tube with a diameter matching that
of the workpiece
- heat the shrink-fi t tube evenly
OTHER APPLICATION EXAMPLE:
★ shrink-wrapping
• Soldering water pipes #
This tool is most suitable for working with soft solders
(melting point below 400°)
- use refl ector nozzle H
- thoroughly clean both joining sections before
soldering
- pre-heat both sections and apply soldering wire
(do not use lead-based soldering wire)
• Thawing out frozen water pipes $
- use refl ector nozzle H
- heat the frozen area evenly
! do no thaw out water pipes made of PVC
! water pipes are often difficult to distinguish from
gas pipes; heating gas pipes is extremely
dangerous – risk of explosion
OTHER APPLICATION EXAMPLES:
★ thawing out frozen car locks (use reduction nozzle J)
★ defrosting freezers (do not damage the plastic
housing)
★ thawing out ice-covered steps and pavements
• Shaping plastic tubes
- use refl ector nozzle H
- fi ll the tube with sand and seal it at both ends,
to avoid kinking of the tube
- heat the tube evenly by moving it from side to side
OTHER APPLICATION EXAMPLES:
★ shaping all plastics with a low melting-point
(polyethylene, PVC etc.)
★ shaping all plastics with a high melting-point (acrylic
glass, Plexiglas etc.)
★ shaping and bending carpet tiles made of synthetic
fi bres
★ shaping and bending of wood (model-building)
• Welding plastics
- the weld seam must be clean and grease-free
- keep welding rod close to weld seam and apply heat,
until the welding rod gets tacky
- remove heat, when weld seam is fi lled up
OTHER APPLICATION EXAMPLES:
★ repairing of surfboards, skis and other synthetic
sports goods (use fl at nozzle G)
★ welding PVC-materials
★ smoothening blisters after sticking PVC-labels
★ connecting garden hoses (use refl ector nozzle H)
• Drying
! only dry with a low or medium temperature
setting (position 1 or 2) and with an increased
distance between the tool and the workpiece
- drying of paint, varnish, gypsum, mortar and plaster
- drying wet timber prior to fi lling
- drying thickly applied fi ller or adhesive quickly
- drying building joints before spraying insulation or
sealant
- drying joints and cracks in boatbuilding
• Cleaning/disinfecting
- disinfecting rabbit hutches, dove cotes, etc. (remove
your pet first)
- combatting ant colonies
- combatting woodworms and boring beetles (hold the
tool at an adequate distance from the wood)
- eliminating weeds
MAINTENANCE / SERVICE
• Always keep tool and cord clean (especially the
ventilation slots E 2)
! disconnect the plug before cleaning
• Never use easy infl ammable liquids for cleaning the
heat gun in general and the air outlet/nozzle in particular
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skileurope.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol % will remind you of this when the need for
disposing occurs
8