Display Function - Panasonic SC-EN38 Operating Instructions Manual

External unit (continued)
MP3
The USB connectivity enables you to connect and play MP3 tracks from
USB mass storage class. Typically, USB memory devices (Bulk only
transfer).
Preparation:
Before connecting any USB mass storage device to the unit, ensure that
the data stored therein has been backed up.
It is not recommended to use a USB extension cable. The device connected
via the cable will not be recognised by this unit.
 Reduce the volume and connect the USB mass storage device.
 Press [USB q/h] to start play.
To pause play
Press [USB q/h].
Press again to resume play.
To stop play
Press [g].
"RESUME" is displayed. The position is
memorized.
Press [USB q/h] to resume play.
OR
Press [g] again to clear the position.
To skip track Press [u, 2] or [i, 1].
To skip album Press [
Press [
numbered buttons in the stop mode.
Direct access play  Press [
(Play starts with the  Press [i, 1] once and then press the
track you select.)
numbered buttons to select the desired track.
Connecting and playing a Bluetooth device
For continental Europe and the U.K.
By connecting a Bluetooth Receiver (e.g SH-FX570R, sold separately),
you can receive and play the audio stored in your Bluetooth audio source
device (mobile phone etc).
male-female cable
(not included)
 Connect the Bluetooth Receiver to the OPTION PORT through
a male-female cable (see the Bluetooth Receiver's instruction
manual).
 Press [q/h, OPTION] to select OPTION as the source.
 Pair and play your Bluetooth audio device (see the device's
instruction manual).
- To play / To pause play
8
Press [q/h, OPTION].
- Other basic operation functions are similar to "USB operations".
(➡ above)
USB operations
USB enabled device
(not included)
or , ALBUM] in the play mode.
or , ALBUM] once and then the
or , ALBUM] to select the album.
Bluetooth Receiver
(not included)
➡ Page 3 for the buttons position of remote control and main unit.
g Display function
Press [DISPLAY] repeatedly during play or pause.
Elapsed time Remaining time
ID3 (Artist) ID3 (Track)
For other operating functions, they are similar as those described in "Disc
operations" (➡ page 5 and 6).
To remove the USB mass storage device
Select a source other than "USB".
Removing the USB mass storage device with it selected as a source can
damage the data stored in the device.
g Compatible device
Devices which are defined as USB mass storage class:
• USB devices that support bulk only transfer.
• USB devices that support USB 2.0 full speed.
g Supported Format
Files must have the extension ".mp3" or ".MP3".
Note
• CBI (Control/Bulk/Interrupt) is not supported.
• A device using NTFS file system is not supported [Only FAT 16/32
(File Allocation Table 16/32) file system is supported].
• Depending on the sector size, some files may not work.
• This unit can access up to 255 albums and 2500 tracks.
• The maximum number of tracks in a folder are 999 tracks.
• Only one memory card will be selected when connecting a multiport
USB card reader. Typically the first memory card inserted.
• Disconnect the USB card reader from the unit when you remove the
memory card. Failure to do so may cause malfunction to the device.
• When you connect your digital audio player to the USB jack, it charges
all the time except in standby mode.
Changing the main unit and
remote control mode
The remote control and main unit are factory-set to "REMOTE 1" mode.
If your remote control affects other equipment during operation, you can
switch to operate in "REMOTE 2" mode.
To switch to "REMOTE 2" mode
 Press [FM/AM/MUSIC P.] to select "AM".
 (While pressing [FM/AM/MUSIC P.] on the main unit)
Press and hold [2] until "REMOTE 2" appears on the main unit
display.
 Press and hold [ENTER] and [2] for at least 2 seconds.
The main unit and remote control are now set to operate in
"REMOTE 2" mode.
To return to "REMOTE 1" mode
Perform steps 1 to 3 but use [1] instead of [2] for steps 2 and 3.
("REMOTE 1" appears on the main unit during step 2.)
The remote control cannot work with the main unit if their modes are
different.
"REMOTE 1" or "REMOTE 2" appears on the main unit when you operate
the remote control.*
* If "REMOTE 1" appears (The main unit is in "REMOTE 1" mode.)
Press and hold [ENTER] and [1] on the remote control for at least 2
seconds.
If "REMOTE 2" appears (The main unit is in "REMOTE 2" mode.)
Press and hold [ENTER] and [2] on the remote control for at least 2
seconds.
Album name Track name
ID3 (Album)