Page 1
ORDER NO. MD0703021CE CD Stereo System SC-EN37P Colour (K)... Black Type System SC-EN37P-K Main Unit: SA-EN37P-K Speakers: SB-EN37AP-K (L) & SB-EN37P-K (R) Specifications n AMPLIFIER SECTION Sampling frequency FTC OUTPUT POWER both channel driven simultaneously 44.1 kHz 10% total harmonic distortion (THD) 32 kHz, 44.1 kHz, 48 kHz...
SC-EN37P Type 1 Way, 1 speaker system Power consumption in standby mode: Speaker(s) 8 cm (5 1/2”) cone type 6 W 2.0 W (appx.) Impedance Notes: · Specifications are subject to change without notice. Input power 3 (MAX) Dimension (W x H x D) 121 mm x 236 mm x 146 mm ·...
Page 3
SC-EN37P 18 Illustration of ICs, Transistors and Diodes 20 Exploded Views 19 Terminal Function of IC's 20.1. Cabinet Parts Location 19.1. IC801 (MN101EF16ZXW) Servo Processor,Digital Signal 20.2. Packaging Processor/Digital filter and D/A Converter 21 Replacement Parts List...
SC-EN37P 1 Safety Precautions 1.1. General Guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, ensure that all the protective devices such as insulation barriers and insulation papers shields are properly installed.
SC-EN37P 1.2. Caution for fuse replacement 1.3. Before repair and adjustment Disconnect AC power, discharge Power Capacitors C611 and C616 through a 10W , 1W resistor to ground. DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.
SC-EN37P 2 Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip”...
SC-EN37P 3 Precaution of laser diode CAUTION: This unit utilizes a class 1 laser diode in the optical pickup unit . Invisible laser radiation is emitted from the optical pickup lens. Wavelength: 780nm When the unit is turned on: 1. Do not look directly into the optical pickup lens.
Page 8
SC-EN37P Caution : The static electricity of your clothes will not be grounded through the wrist strap. So, take care not to let your clothes touch the traverse deck (optical pickup). Caution when replacing the Traverse Deck The traverse deck has a short point shorted with solder to protect the laser diode against electrostatics breakdown. Be sure to...
SC-EN37P 5 About Lead Free Solder (PbF) 5.1. Service caution based on legal restrictions 5.1.1. General description about Lead Free Solder (PbF) The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation.
SC-EN37P 8 Self diagnosis and special mode setting This unit is equipped with features of self-diagnostic & special mode setting for checking the functions & reliability. 8.1. Service Mode Summary Table The service mode can be activated by pressing various button combination on the main unit and remote control unit. Below is the...
Page 14
SC-EN37P Item FL Display Key Operation Mode Name Description Front Key Doctor Mode To enter into Doctor Mode for DIsplay 1 In any mode: checking of various items and 1. Press [ ] button on main unit displaying EEPROM and firmware follow by [4] and [7] on remote version.
Page 15
SC-EN37P Item FL Display Key Operation Mode Name Description Front Key Volume Setting To check for the volume setting of the In doctor mode: Mode main unit. The volume will be 1. Press [7] button on remote control. automatically set to its respective level (in dB).
SC-EN37P Below is the procedures for this mode. Step 1: Enter into Doctor mode (For more information refer to section 8.2 on key operation to enter into this mode). Step 2: When [ ], [1] & [4] are pressed at the doctor mode, the following shall be displayed for 3s. The result shall correspond to the condition met as shown in the table below: 8.3.
SC-EN37P 9 Assembling and Disassembling 9.1. Caution “ATTENTION SERVICER” Some chassis components may have sharp edges. Be careful when disassembling and servicing. 1. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components.
SC-EN37P 9.2. Disassembly flow chart The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the servicing. To assemble the unit, reverse the steps shown in the chart as below. 9.2.1.
SC-EN37P 9.4. Disassembly of rear cabinet Step 1 Remove 10 screws. Step 2 Lift up the rear cabinet. Step 3 Detach cable (FP806) on Main P.C.B. and remove the rear cabinet as arrow shown. 9.5. Disassembly of D-Port P.C.B. · Follow the (Step 1) - (Step 3) of Item 9.4 - Disassembly of rear cabinet Step 1 Remove 2 screws.
SC-EN37P Step 1 Release 3 catches and remove the Traverse Cover. Step 3 Widening the catch, push the fixed pin in. (a) fi (b) Step 4 Lift up the traverse unit to remove it. Step 2 Pull out FFC. Caution: Keep the floating springs (x 4) in safe place &...
SC-EN37P Step 2 Remove 3 screws. Step 4 Detach FFC out from the connector. Step 3 Flip the CD Servo P.C.B. over to one side. Step 5 Attach a short pin to the unit. Caution: Insert a short pin into FFC of the optical pickup. [See “Handling Precautions for traverse unit”].
SC-EN37P 9.13. Disassembly of CD Block & CD Lid · Follow the (Step 1) - (Step 3) of Item 9.4 - Disassembly of rear cabinet · Follow the (Step 1) - (Step 2) of Item 9.7 - Disassembly of Main P.C.B. , Sensor P.C.B. & Tuner P.C.B.
SC-EN37P 9.14. Disassembly of Speakers 9.14.1. Disassembly of the speaker (SB-EN37) - (R) Step 1 Remove 6 screws. Step 4 Remove 4 screws. · Disassembly of net frame ass’y Step 5 Remove 4 screws. Step 2 Remove the back cabinet ass’y..
Page 27
SC-EN37P 9.14.2. Disassembly of the rear cabinet (SB-EN37A) - (L) Step 1 Remove 6 screws. Step 2 Remove the back cabinet ass’y.. Step 3 Unsolder the lead wires. Step 4 Remove 4 screws.
Page 28
SC-EN37P Step 1 Remove 1 screw on back cabinet assy. Step 2 Remove 3 screws to remove the port unit. Step 3 Remove 4 screws on Transformer P.C.B. unit. · Disassembly of net frame ass’y Step 5 Remove 4 screws.
SC-EN37P 10 Service Fixture and Tools Service Tools Extension FFC (A) CD Servo P.C.B. - Main P.C.B. REEX0485 (14 Pins) 11 Service Positions General procedures: Connect the DC in cord cable from (SB-EN37A) to main set, connect AC power supply cord to speaker to on the set. Load in cd and switch off the set.
SC-EN37P 11.2. Check and repair of Main P.C.B., Sensor P.C.B., Tuner P.C.B., Motor P.C.B., D-Port P.C.B., Panel P.C.B., LED P.C.B., Power Switch P.C.B., Tact Switch P.C.B. & Switch P.C.B.
SC-EN37P 12 Voltage and Waveform Chart Note: Circuit voltage and waveform described herein shall be regarded as reference information when probing defect point, because it may differ from an actual measuring value due to difference of Measuring instrument and its measuring condition and product itself.
SC-EN37P 15 Notes of Schematic Diagrams (All schematic diagrams may be modified at any time with the development of the new technology) S351 : CD TOP Switch S352 : CD BOTTOM Switch S801 : POWER Switch ( S802 : VOL - Switch (...
SC-EN37P 17 Printed Circuit Board Note: Circuit board diagrams may be modified at any time with the development of new technology. 17.1. (A) CD Servo P.C.B. & (B) Tuner P.C.B.
SC-EN37P 19 Terminal Function of IC's 19.1. IC801 (MN101EF16ZXW) Servo Processor,Digital Signal Processor/Digital filter and D/A Converter Pin No. Mark Function Pin No. Mark Function PCONT1 Power Control Output PLL_DI PLL Data Input (PWR Sply Active HIGH) N.C. No connection DPORT_PCONT 5.3V Regulator Control...
SC-EN37P 21 Replacement Parts List Notes: · Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardent (resistors), high-quality sound (capacitors), low noise (resistors), etc are used. When replacing any of these components, be sure to use only manufacturer’s specified parts shown in the parts list.
Page 66
SC-EN37P Ref. No. Part No. Part Name & Description Remarks Ref. No. Part No. Part Name & Description Remarks REPV0136A LED P.C.B. [M](RTL) D605 B0AACK000004 DIODE REPV0136A POWER SWITCH P.C.B. [M](RTL) D607 B0AACK000004 DIODE REPV0136A TACT SWITCH P.C.B. [M](RTL) D608...
Page 67
SC-EN37P Ref. No. Part No. Part Name & Description Remarks Ref. No. Part No. Part Name & Description Remarks L503 ERJ3GEY0R00V CHIP JUMPER W720 ERJ6GEY0R00V CHIP JUMPER L504 ERJ3GEY0R00V CHIP JUMPER W721 ERJ8GEY0R00V CHIP JUMPER L601 G0C101KA0029 AXIAL COIL W722...
Page 68
SC-EN37P Ref. No. Part No. Part Name & Description Remarks Ref. No. Part No. Part Name & Description Remarks JW601 RWJ9006080SX 6P SENSOR-MAIN WIRE R202 D0GB562JA008 5.6K 1/16W JW802 RWJ0209070SX 9P LCD-MAIN WIRE R203 D0GB473JA008 47K 1/16W JW803 REXV0076 2P OPE1-MAIN WIRE...
Page 69
SC-EN37P Ref. No. Part No. Part Name & Description Remarks Ref. No. Part No. Part Name & Description Remarks R644 D0GB562JA008 5.6K 1/16W R3007 D0GB125JA007 1.2M 1/16W R645 D0GB223JA008 22K 1/16W R3008 ERJ3GEYJ224V 220K 1/16W R646 D0GB392JA008 3.9K 1/16W R3009...
Page 70
SC-EN37P Ref. No. Part No. Part Name & Description Remarks Ref. No. Part No. Part Name & Description Remarks F2A1H1R0A145 1 50V C305 F1H1H221A748 220P 50V F2A0J101A167 100 6.3V C309 ECEA1AKA470B 47 10V F2A1H1R0A145 1.0 50V C310 F2A1C101A147 100 16V...