1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Copier
  5. AR-407
  6. Operation manual

Sharp AR-407 Operation Manual

Digital copying machine
Hide thumbs Also See for AR-407:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual
AR-287/AR-337
AR-407
MODEL
AR-287
AR-337
AR-407
DIGITAL COPYING MACHINE
OPERATION MANUAL
GETTING STARTED
MAKING COPIES
SPECIAL FUNCTIONS
SUPPLIES
COPIER TROUBLE?
GENERAL
INFORMATION
OPTIONAL EQUIPMENT
KEY OPERATOR'S
GUIDE
Page
1-1
2-1
3-1
4-1
5-1
6-1
7-1
8-1

Advertisement

Table of Contents

Troubleshooting

loading

Related Manuals for Sharp AR-407

Summary of Contents for Sharp AR-407

  • Page 1 AR-287/AR-337 AR-407 MODEL AR-287 AR-337 AR-407 DIGITAL COPYING MACHINE OPERATION MANUAL GETTING STARTED MAKING COPIES SPECIAL FUNCTIONS SUPPLIES COPIER TROUBLE? GENERAL INFORMATION OPTIONAL EQUIPMENT KEY OPERATOR’S GUIDE Page...
  • Page 2 Warning This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. In some areas, the "POWER" switch positions are marked "I" and " instead of "ON"...

  • Page 3: Table Of Contents

    CONTENTS INTRODUCTION ... 2 USING THIS MANUAL ... 2 CHAPTER 1 GETTING STARTED INSTALLATION REQUIREMENTS ... 1-2 CAUTIONS ... 1-3 POWER ON AND OFF ... 1-5 Power save modes ... 1-6 INFORMATION FUNCTION ... 1-7 USING THE TOUCH PANEL ... 1-8 How to use the touch panel ...
  • Page 4 AUDITING ACCOUNTS If this copier has been programmed in the auditing mode, it will not function until an assigned 5-digit account number has been entered. KEY OPERATOR See page 8-9 for setting the auditing mode. INTERRUPT CLEAR AUDIT CLEAR PROGRAM The initial status of the message display will be: Enter your account number using the 10-key pad.

  • Page 5: Getting Started

    CHAPTER 1 GETTING STARTED This chapter describes the basic information on the use of this copier. Page INSTALLATION REQUIREMENTS ... 1-2 CAUTIONS ... 1-3 POWER ON AND OFF ... 1-5 Power save modes ... 1-6 INFORMATION FUNCTION ... 1-7 USING THE TOUCH PANEL ... 1-8 How to use the touch panel ...

  • Page 6: Installation Requirements

    INSTALLATION REQUIREMENTS To ensure safety and proper machine performance, please note the following before initial installation and whenever the machine is to be relocated. The copier should be installed near an accessible power outlet for easy connection. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements.

  • Page 7: Cautions

    CAUTIONS Do not touch the photoconductive drum. Scratches or smudges on the drum will cause dirty copies. The fusing unit is extremely hot. Exercise care in this area. 3. Since a hard disk drive is built into the copier, be sure to turn the power switch to the “OFF”...
  • Page 8 CAUTIONS For Europe: CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT CAUTION INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM. VORSICHT UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET UND SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN.

  • Page 9: Power On And Off

    UP. PLEASE WAIT.” will appear in the message display. Warming Power on up takes about 65 seconds for the AR-287/337 and about 75 seconds for the AR-407. Once the copier is ready, the message display will change to “READY TO COPY.”, and the START ( ) key indicator will light up, indicating that copying is possible.

  • Page 10: Power Save Modes

    POWER ON AND OFF Power save modes The copier has two power save modes to reduce overall power consumption and thereby reduce the cost of operation and to conserve natural resources to help reduce environmental pollution. The two power save modes are preheat mode and auto power shut-off mode. KEY OPERATOR The preheat activation time and the auto power shut-off time have been preset at the factory to 15 min.

  • Page 11: Information Function

    INFORMATION FUNCTION The information function provides a quick reference guide to the use of the various features and functions of this copier. The information mode can be entered when the copier is in the standby mode. EXIT INFORMATION SELECT INFORMATION. COPIER ADDING TONER INSTRUCTIONS...

  • Page 12: Using The Touch Panel

    USING THE TOUCH PANEL How to use the touch panel READY TO COPY. 1. A4 2. A3 AUTO AUTO 8/ 11 100% EXPOSURE PAPER SELECT COPY RATIO RECALL STORE/DELETE Selection of function CANCEL ERASE (0~20) EDGE ERASE CENTRE ERASE EDGE+CENTRE ERASE READY TO COPY.

  • Page 13: Function Setting Icons

    Function setting icons READY TO COPY. 1. A4 2. A3 READY TO COPY. CANCEL ERASE (0~20) EDGE ERASE CENTRE ERASE EDGE+CENTRE ERASE Margin shift (p.3-4) Erase (p.3-6) Dual page copying (p.3-8) Multi shot (p.3-10) Covers (p.3-13) Transparency film with insert sheets (p.3-15) Pamphlet copy (p.3-17) Job build (p.3-20)

  • Page 15: Making Copies

    CHAPTER 2 MAKING COPIES This chapter describes the basic copying functions such as normal copying, reduction/enlargement, and exposure adjustments. Page AUDITING ACCOUNTS ... 2-2 USING THE RADF ... 2-3 COPYING FROM THE DOCUMENT GLASS ... 2-8 REDUCTION/ENLARGEMENT/ZOOM ... 2-11 SPECIAL PAPERS (manual feed) ... 2-14 Two sided copying with bypass tray ...

  • Page 16: Auditing Accounts

    AUDITING ACCOUNTS If this copier has been programmed in the auditing mode, it will not function until an assigned 5-digit account number has been entered. KEY OPERATOR See page 8-9 for setting the auditing mode. INTERRUPT CLEAR AUDIT CLEAR PROGRAM The initial status of the message display will be: ENTER YOUR ACCOUNT NUMBER.

  • Page 17: Using The Radf

    USING THE RADF The RADF (reversing automatic document feeder) will handle multiple originals. Before loading originals into the document feeder tray, be sure to remove any staples or paper clips from them. Damaged or crumpled originals or originals which have been folded may misfeed in the RADF or cause incorrect size detection.

  • Page 18: Using The Radf

    USING THE RADF READY TO COPY. (DOCUMENT FEEDER MODE) ORIGINAL AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO INTERRUPT CLEAR AUDIT CLEAR PROGRAM INTERRUPT CLEAR ALL START CLEAR 1-sided copies of 1-sided originals 1-sided copies of 1-sided originals Adjust the original guides to the size of the originals and set the originals face up in the document feeder tray.
  • Page 19 Maximum height line AUTO READY TO COPY.(DOCUMENT FEEDER MODE) 2-SIDED COPY AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO READY TO COPY.(DOCUMENT FEEDER MODE) 2-SIDED COPY AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO CLEAR ALL START AUDIT CLEAR PROGRAM 2-sided copies from 1-sided originals Adjust the original guides to the size of the originals and...
  • Page 20 USING THE RADF Maximum height line AUTO READY TO COPY.(DOCUMENT FEEDER MODE) 2-SIDED COPY AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO READY TO COPY.(DOCUMENT FEEDER MODE) 2-SIDED COPY AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO CLEAR ALL START AUDIT CLEAR PROGRAM...
  • Page 21 Maximum height line AUTO READY TO COPY.(DOCUMENT FEEDER MODE) 2-SIDED COPY AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO READY TO COPY.(DOCUMENT FEEDER MODE) 2-SIDED COPY AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO CLEAR ALL START AUDIT CLEAR PROGRAM 1-sided copies from 2-sided originals Adjust the original guides to the size of the originals and...

  • Page 22: Copying From The Document Glass

    COPYING FROM THE DOCUMENT GLASS Use the document glass for copying single originals, bound documents, and other originals that cannot be set in the RADF. Only 1-sided to 1-sided and 1-sided to 2-sided copying can be selected when copying from the document glass.

  • Page 23: Copying From The Document Glass

    INTERRUPT CLEAR ALL START CLEAR PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END]. READ-END AUTO 100% AUTO A4 EXPOSURE PAPER SELECT COPY RATIO Original size detector Centring scale AUTO COPYING FROM THE DOCUMENT GLASS Press the START ( ) key. If the copier is in the GROUP mode (the sort icon is not displayed on the touch panel), copying will start and the number in the copy quantity display will decrease by 1 each time a copy is made.
  • Page 24 COPYING FROM THE DOCUMENT GLASS READY TO COPY. 2-SIDED COPY AUTO 100% AUTO A4 EXPOSURE PAPER SELECT COPY RATIO READY TO COPY. 2-SIDED COPY AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO CLEAR ALL START AUDIT CLEAR PROGRAM PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END].

  • Page 25: Reduction/Enlargement/Zoom

    “ZOOM” keys on the touch panel. The zoom function enables precise copy ratio selection from 25% to 400% (for the AR-407) or from 25% to 800% (for the AR-287 and AR- 337) in 1% increments. KEY OPERATOR A total of four extra preset copy ratios, two each for reduction and enlargement, can be added.
  • Page 26 100% 141% A3 A4 A4 A3 XY ZOOM MENU AUTO IMAGE AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO MENU 2 (AR-407) READY TO COPY. 200% ZOOM 400% 800% 100% 101% 110% XY ZOOM MENU 1 AUTO IMAGE AUTO...
  • Page 27 READY TO COPY. A4 B5 B5 A4 115% A3 B4 B4 A3 ZOOM B5 A5 A5 B5 122% B4 A4 A4 B4 A4 A5 A5 A4 100% 141% A3 A4 A4 A3 XY ZOOM MENU AUTO IMAGE AUTO AUTO A3 100% EXPOSURE PAPER SELECT...

  • Page 28: Special Papers (Manual Feed)

    Insert the copy paper all the way into the bypass tray. Labels, tracing paper, and other special purpose papers other than SHARP recommended transparency film must be fed individually. Multiple sheets of SHARP recommended transparency film can be loaded in the bypass tray.

  • Page 29: Two-Sided Copying With Bypass Tray

    Two-sided copying with bypass tray Two-sided copies can be made manually using the bypass tray, when the heavy paper which is out of spec. for duplex module is used. CLEAR ALL START O A4 100% R SELECT COPY RATIO SPECIAL PAPERS (manual feed) Place the first original face down on the document glass and make a copy.

  • Page 30: Exposure Adjustments

    EXPOSURE ADJUSTMENTS This copier has four exposure modes to choose from: AUTOMATIC, TEXT, TEXT/PHOTO and PHOTO. AUTO EXPOSURE AUTO EXPOSURE PAPER AUTO 1. A4 2. A3 TEXT TEXT/PHOTO PHOTO AUTO A EXPOSURE PAPER SE TEXT/PHOTO EXPOSURE PAPE 2-16 Automatic This is the standard initial setting for this copier. In this mode, the characteristics of an original being copied are “read”...

  • Page 31: Sort/Group

    SORT/GROUP When the SORT ( ) icon is indicated on the touch panel, copies will be collated by sets and then delivered to the exit tray. When the SORT ( ) icon is not indicated, copies will be grouped by originals. When the RADF is used for copying, copies will be collated in the default setting.

  • Page 32: Job Memory

    JOB MEMORY Frequently used job programs can be stored in one of nine storage registers. This is convenient for quick job recall without losing time manually reprogramming each aspect of the job. All functions that can be set in the copy mode except the copy quantity setting can be stored in the job memory.

  • Page 33: Job Memory

    EXIT JOB PROGRAMS PRESS PROGRAM NUMBER. RECALL STORE/DELETE JOB PROGRAMS PRESS PROGRAM NUMBER. A JOB PROGRAM HAS BEEN ALREADY STORED. STORE ANOTHER PROGRAM? CANCEL DELETE STORE RECALL STORE/DELETE EXIT JOB PROGRAMS PRESS PROGRAM NUMBER. RECALL STORE/DELETE CLEAR LEAR PROGRAM EXIT JOB PROGRAMS PRESS PROGRAM NUMBER.

  • Page 34: Interrupting A Copy Run

    INTERRUPTING A COPY RUN INTERRUPT can be used to temporarily stop a long copy run so that another job can be run. INTERRUPT will not function during duplex copying. Duplex copying, tandem copying and the JOB BUILD function can not be selected during interrupt copying. When an optional dual tray output unit (AR-TR1) is installed, interrupt copies are output to the second tray of the unit.

  • Page 35: Special Functions

    CHAPTER 3 SPECIAL FUNCTIONS This chapter describes the special copying functions including various image editing functions which have been made possible by digital image processing technology. Page XY ZOOM ... 3-2 MARGIN SHIFT ... 3-4 ERASE ... 3-6 DUAL PAGE COPYING ... 3-8 MULTI SHOT ...

  • Page 36: Xy Zoom

    The XY ZOOM feature allows the horizontal and vertical copy ratios to be changed independently. If this feature is selected, the copy ratios can be set from 25% to 400% (for the AR-407) or from 25% to 800% (for the AR-287 and AR-337). The illustrations below describe the case of the AR-407.
  • Page 37 TO COPY. ZOOM 100% READY TO COPY. ZOOM 141% 100% 200% CANCEL XY ZOOM AUTO AUTO A4 400% EXPOSURE PAPER SELECT READY TO COPY. 1. A4 2. A3 AUTO AUTO 8/ 11 X-50% Y-70% EXPOSURE PAPER SELECT COPY RATIO CLEAR ALL START AUDIT CLEAR PROGRAM...

  • Page 38: Margin Shift

    MARGIN SHIFT Original Copy Expanded margin (Initial setting: copy image shifted to the right) Margin is expanded here. Margin is expanded here. READY TO CO The MARGIN SHIFT feature, in its initial setting, automatically shifts the text or image to the right both on one-sided copies and on the front side of two- sided copies.

  • Page 39: Margin Shift

    READY TO COPY. SPECIAL MODES DUAL PAGE MARGIN SHIFT ERASE COPY TRANSPARENCY MULTI SHOT COVERS INSERTS TEXT STAMP PAMPHLET COPY IMAGE EDIT AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO CANCEL MARGIN SHIFT RIGHT LEFT SIDE 1 DOWN (0~20) RIGHT LEFT SIDE 1...

  • Page 40: Erase

    ERASE Edge erase Centre erase Edge + Centre erase READY TO CO READY TO COPY. SPECIAL MODES DUAL PAGE MARGIN SHIFT ERASE COPY TRANSPARENCY MULTI SHOT COVERS INSERTS PAMPHLET COPY IMAGE EDIT TEXT STAMP AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO This copier has an edge erase mode and a centre erase mode.
  • Page 41 READY TO COPY. CANCEL ERASE (0~1) inch EDGE ERASE CENTRE ERASE EDGE+CENTRE ERASE CANCEL ERASE (0~20) EDGE ERASE CENTRE ERASE EDGE+CENTRE ERASE CANCEL (0~1) inch INTERRUPT CLEAR ALL START CLEAR PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END]. READ-END AUTO AUTO A4 100%...

  • Page 42: Dual Page Copying

    DUAL PAGE COPYING Paper size index READY TO CO READY TO COPY. SPECIAL MODES DUAL PAGE MARGIN SHIFT ERASE COPY TRANSPARENCY MULTI SHOT COVERS INSERTS TEXT STAMP PAMPHLET COPY IMAGE EDIT AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO DUAL PAGE COPY TRANSPARENCY...

  • Page 43: Dual Page Copying

    EADY TO COPY. 11 17 ORIGINAL 1. A4 2. A3 AUTO IMAGE AUTO 100% EXPOSURE PAPER SELECT COPY RATIO INTERRUPT CLEAR AUDIT CLEAR PROGRAM INTERRUPT CLEAR ALL START CLEAR PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END]. READ-END AUTO IMAGE AUTO 100% EXPOSURE...

  • Page 44: Multi Shot

    MULTI SHOT READY TO COPY. 1. A4 2. A3 AUTO AUTO 8/ 11 100% EXPOSURE PAPER SELECT COPY RATIO AUTO READY TO CO 3-10 The MULTI SHOT function is used to copy several originals, collectively in a specified order, onto one sheet. When the MULTI SHOT is selected, the copy ratio is limited between 25% and 400%.

  • Page 45: Multi Shot

    READY TO COPY. SPECIAL MODES DUAL PAGE MARGIN SHIFT ERASE COPY TRANSPARENCY MULTI SHOT COVERS INSERTS TEXT STAMP PAMPHLET COPY IMAGE EDIT AUTO 100% EXPOSURE PAPER SELECT COPY RATIO CANCEL MULTI SHOT LAYOUT BORDER 2inl 4inl 8inl 16inl CANCEL MULTI SHOT LAYOUT BORDER 2inl...
  • Page 46 MULTI SHOT CANCEL SHOT LAYOUT BORDER LINE 4inl 16inl INTERRUPT CLEAR AUDIT CLEAR PROGRAM INTERRUPT CLEAR ALL START CLEAR PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END]. READ-END AUTO IMAGE AUTO 100% EXPOSURE PAPER SELECT COPY RATIO 3-12 Press the upper “OK” key. Enter the desired number of copies.

  • Page 47: Covers

    COVERS AUTO READY TO CO READY TO COPY.(DOCUMENT FEEDER MODE) SPECIAL MODES DUAL PAGE MARGIN SHIFT ERASE COPY TRANSPARENCY MULTI SHOT COVERS INSERTS TEXT STAMP PAMPHLET COPY IMAGE EDIT AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO The COVERS mode is used to place covers on the front, back, or both the front and back of multipage documents.
  • Page 48 COVERS CANCEL COVERS PRINT ON FRONT FRONT BACK FRONT+BACK CANCEL PRINT ON FRONT COVER? NT+BACK NCEL T ON FRONT COVER? CLEAR ALL START AUDIT CLEAR PROGRAM 3-14 Select cover placement. Select “FRONT”, “BACK” or “FRONT+BACK” on the touch panel. Indicate whether the front cover sheets are copied on or not.

  • Page 49: Transparency Film With Insert Sheets

    TRANSPARENCY FILM WITH INSERT SHEETS INSERTS WITH PRINTING INSERTS WITHOUT PRINTING READY TO CO READY TO COPY. SPECIAL MODES DUAL PAGE MARGIN SHIFT ERASE COPY TRANSPARENCY MULTI SHOT COVERS INSERTS TEXT STAMP PAMPHLET COPY IMAGE EDIT AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO...

  • Page 50: Transparency Film With Insert Sheets

    TRANSPARENCY FILM WITH INSERT SHEETS CANCEL PRINT ON THE INSERT SHEETS? THE INSERT ORIGINAL 1. A4 2. A3 AUTO A4 100% PAPER SELECT COPY RATIO INTERRUPT CLEAR ALL START CLEAR PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END]. READ-END AUTO AUTO A4 100%...

  • Page 51: Pamphlet Copy

    PAMPHLET COPY Originals (1-sided) Originals (2-sided) READY TO CO The PAMPHLET COPY function is used to arrange copies in proper order for eventual centre-stapling and folding into a booklet. Four pages will be copied onto one sheet. Centre stapling cannot be performed by this copier. Even if PAMPHLET COPY is selected and the optional finishers (AR-FN1N, AR-FN2) is installed, centre-stapling cannot be performed.
  • Page 52 PAMPHLET COPY READY TO COPY. SPECIAL MODES DUAL PAGE MARGIN SHIFT ERASE COPY TRANSPARENCY MULTI SHOT COVERS INSERTS PAMPHLET COPY TEXT STAMP IMAGE EDIT AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO READY TO COPY. CANCEL PAMPHLET COPY ORIGINAL LEFT BINDING 1-SIDED 2-SIDED...
  • Page 53 PAPER SELECT INTERRUPT CLEAR AUDIT CLEAR PROGRAM INTERRUPT CLEAR ALL START CLEAR PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END]. READ-END AUTO IMAGE AUTO EXPOSURE PAPER SELECT Check the copy paper selection. When the desired paper size is not selected, touch the desired paper tray on the touch panel then the AUTO IMAGE key.

  • Page 54: Image Editing Functions

    IMAGE EDITING FUNCTIONS The image editing functions include the following functions. Job build: Makes copies from a large volume of originals (up to 120 pages of A4 (8-1/2" x 11") paper size) using the document feeder. Centring: Shifts the image to the centre of copy paper when the original and the copy paper are of different sizes.
  • Page 55 READY TO CO READY TO COPY. SPECIAL MODES DUAL PAGE MARGIN SHIFT ERASE COPY TRANSPARENCY MULTI SHOT COVERS INSERTS TEXT STAMP PAMPHLET COPY IMAGE EDIT AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO READY TO COPY. SPECIAL MODES IMAGE EDIT JOB BUILD CENTRING REPEAT COPY...

  • Page 56: Centring

    IMAGE EDITING FUNCTIONS INTERRUPT CLEAR ALL START CLEAR PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END]. READ-END AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO CENTRING 3-22 Press the START ( ) key. Scanning of the first section will start. After the first section of original pages has been fed and the START lights up, remove the scanned originals from the exit area, set the next section of original pages into...
  • Page 57 READY TO COPY. 1. A4 2. A3 AUTO AUTO 8/ 11 100% EXPOSURE PAPER SELECT COPY RATIO READY TO CO READY TO COPY. SPECIAL MODES DUAL PAGE MARGIN SHIFT ERASE COPY TRANSPARENCY MULTI SHOT COVERS INSERTS TEXT STAMP PAMPHLET COPY IMAGE EDIT AUTO 100%...

  • Page 58: Repeat Copy

    IMAGE EDITING FUNCTIONS INTERRUPT CLEAR ALL START CLEAR PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END]. READ-END AUTO IMAGE AUTO 100% EXPOSURE PAPER SELECT COPY RATIO REPEAT COPY 3-24 Press the START ( ) key. If the document feeder is used, scanning of originals and copying will start.
  • Page 59 8/ 11R 1. A4 2. A3 AUTO AUTO A4 POSURE PAPER SELECT COPY RA READY TO CO READY TO COPY. SPECIAL MODES DUAL PAGE MARGIN SHIFT ERASE COPY TRANSPARENCY MULTI SHOT COVERS INSERTS TEXT STAMP PAMPHLET COPY IMAGE EDIT AUTO 100% EXPOSURE PAPER SELECT...
  • Page 60 IMAGE EDITING FUNCTIONS CANCEL BORDER LINE CANCEL BORDER LINE INTERRUPT CLEAR AUDIT CLEAR PROGRAM INTERRUPT CLEAR ALL START CLEAR PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END]. READ-END AUTO IMAGE AUTO 100% EXPOSURE PAPER SELECT COPY RATIO 3-26 Select a type of border line. Select the solid line, broken line or no border line.

  • Page 61: B/W Reverse

    B/W REVERSE READY TO CO READY TO COPY. SPECIAL MODES DUAL PAGE MARGIN SHIFT ERASE COPY TRANSPARENCY MULTI SHOT COVERS INSERTS TEXT STAMP PAMPHLET COPY IMAGE EDIT AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO READY TO COPY. SPECIAL MODES IMAGE EDIT JOB BUILD CENTRING...
  • Page 62 IMAGE EDITING FUNCTIONS CENTRING REPEAT COPY INTERRUPT CLEAR AUDIT CLEAR PROGRAM INTERRUPT CLEAR ALL START CLEAR PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END]. READ-END AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO 3-28 Press the upper “OK” key. Make all other desired copier selections and enter the desired number of copies.

  • Page 63: Binding Change

    BINDING CHANGE This function rotates the image of originals of the second side in the 1-sided to 2-sided copy mode. This function is useful for copying B4 or A3 (8-1/2" x 14" or 11" x 17") originals in the 1-sided to 2-sided copy mode to allow left side binding.
  • Page 64 IMAGE EDITING FUNCTIONS AUTO READY TO CO READY TO COPY. SPECIAL MODES DUAL PAGE MARGIN SHIFT ERASE COPY TRANSPARENCY MULTI SHOT COVERS INSERTS TEXT STAMP PAMPHLET COPY IMAGE EDIT AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO READY TO COPY. SPECIAL MODES IMAGE EDIT JOB BUILD...
  • Page 65 CENTRING REPEAT COPY INTERRUPT CLEAR AUDIT CLEAR PROGRAM INTERRUPT CLEAR ALL START CLEAR PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END]. READ-END AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO IMAGE EDITING FUNCTIONS Press the upper “OK” key. Make all other desired copier selections and enter the desired number of copies.

  • Page 66: Text Stamp

    TEXT STAMP The text stamp functions include the following functions. Date: Adds the current date to the copies. Select stamp: Adds a selected stamp to the copies. The stamp will be printed in white on a shaded background. Watermark: Adds a selected watermark to the copies. The watermark will be printed in gray tone.

  • Page 67: Text Stamp

    READY TO COPY. SPECIAL MODES DUAL PAGE MARGIN SHIFT ERASE COPY TRANSPARENCY MULTI SHOT COVERS INSERTS TEXT STAMP PAMPHLET COPY IMAGE EDIT AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO PECIAL MODES EXT STAMP SELECT DATE STAMP PAGE WATERMARK NUMBER PRINT DIRECTION...
  • Page 68 TEXT STAMP SELECT DATE STAMP PAGE WATERMARK NUMBER PRINT DIRECTION STAMP SELECT DATE STAMP PAGE WATERMARK NUMBER PRINT DIRECTION INTERRUPT CLEAR AUDIT CLEAR PROGRAM INTERRUPT CLEAR ALL START CLEAR PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END]. READ-END AUTO AUTO A4 100% EXPOSURE...

  • Page 69: Select Stamp

    SELECT STAMP Urgent READY TO CO READY TO COPY. SPECIAL MODES DUAL PAGE MARGIN SHIFT ERASE COPY TRANSPARENCY MULTI SHOT COVERS INSERTS TEXT STAMP PAMPHLET COPY IMAGE EDIT AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO PECIAL MODES EXT STAMP SELECT DATE STAMP...
  • Page 70 TEXT STAMP SELECT STAMP CANCEL Confidential Urgent Copy Preliminary Draft Final OPTION CANCEL 1ST PAGE Urgent ONLY Preliminary Final ALL PAGES Confidential Urgent Copy Preliminary Draft Final OPTION SELECT STAMP DARKNESS CANCEL POSITION 3-36 Select the desired stamp to be printed. The selected stamp will be highlighted.
  • Page 71 CANCEL POSITION SELECT DATE STAMP PAGE WATERMARK NUMBER PRINT DIRECTION SELECT DATE STAMP PAGE WATERMARK NUMBER TION CLEAR ALL START AUDIT CLEAR PROGRAM PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END]. READ-END AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO Press the lower “OK”...

  • Page 72: Watermark

    TEXT STAMP WATERMARK Draft Draft READY TO CO READY TO COPY. SPECIAL MODES DUAL PAGE MARGIN SHIFT ERASE COPY TRANSPARENCY MULTI SHOT COVERS INSERTS TEXT STAMP PAMPHLET COPY IMAGE EDIT AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO 3-38 The WATERMARK function adds a selected watermark such as “Confidential”...
  • Page 73 PECIAL MODES EXT STAMP SELECT DATE STAMP PAGE WATERMARK NUMBER PRINT DIRECTION WATERMARK CANCEL Confidential Urgent Copy Preliminary Draft Final OPTION CANCEL 1ST PAGE Urgent ONLY Preliminary Final ALL PAGES Confidential Urgent Copy Preliminary Draft Final OPTION TERMARK CANCEL DARKNESS Press the “WATERMARK”...
  • Page 74 TEXT STAMP CANCEL SELECT DATE STAMP PAGE WATERMARK NUMBER PRINT DIRECTION SELECT DATE STAMP PAGE WATERMARK NUMBER CLEAR ALL START AUDIT CLEAR PROGRAM PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END]. READ-END AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO 3-40 Press the lower “OK”...

  • Page 75: Page Number

    PAGE NUMBER READY TO CO READY TO COPY. SPECIAL MODES DUAL PAGE MARGIN SHIFT ERASE COPY TRANSPARENCY MULTI SHOT COVERS INSERTS TEXT STAMP PAMPHLET COPY IMAGE EDIT AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO The PAGE NUMBER function adds page numbers to the copies. The page number format can be selected from three types.
  • Page 76 TEXT STAMP PECIAL MODES EXT STAMP SELECT DATE STAMP PAGE WATERMARK NUMBER PRINT DIRECTION GE NUMBER CANCEL FIRST PAGE NUMBER -1-,-2-,-3-.. 1/5,2/5,3/5.. 1,2,3... CANCEL FIRST PAGE NUMBER -1-,-2-,-3-.. 1/5,2/5,3/5.. (0~) 1,2,3... CANCEL FIRST PAGE NUMBER -1-,-2-,-3-.. 1/5,2/5,3/5.. (0~) 1,2,3... SELECT DATE STAMP PAGE...
  • Page 77 EXT STAMP SELECT DATE STAMP PAGE WATERMARK NUMBER PRINT DIRECTION CLEAR ALL START AUDIT CLEAR PROGRAM PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END]. READ-END AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO Press the upper “OK” key. Make all other desired copier selections and enter the desired number of copies.

  • Page 78: Tandem Copy

    The TANDEM COPY key will only be displayed on the touch panel of the machine set as the main copier, (an authorised Sharp Service Technician will do the setting of the main and sub copiers at the time of installation).
  • Page 79 DUAL PAGE COPY TRANSPARENCY INSERTS INTERRUPT CLEAR AUDIT CLEAR PROGRAM INTERRUPT CLEAR ALL START CLEAR Press the “OK” key. Make all other desired copier settings and enter the number of copies. The functions selected on the main copier will be used by both copiers. (1) The key operator programs of which settings at the main copier are given priority (the settings at the sub copier are disregarded): Exposure Adjustment, Toner Save Mode, Initial Margin Shift,...

  • Page 80: Setting Review

    SETTING REVIEW The current settings of copier functions can be displayed on the touch panel. 100% COPY RATIO IDED COPIES OF 1-SIDED GINALS PLE SORT HIFT : SIDE 1 SIDE 2 10 mm 10 mm 2inl NO BORDER Confidential TAMP : 1ST PAGE ONLY EXIT ED COPIES OF 1-SIDED...

  • Page 81: Supplies

    CHAPTER 4 SUPPLIES This chapter describes the supplies for this copier such as paper and toner. Page PAPER ... 4-2 Types and sizes of copy paper ... 4-2 Loading copy paper ... 4-2 ADDING TONER ... 4-5 USED TONER DISPOSAL ... 4-7 STORAGE OF SUPPLIES ...

  • Page 82: Paper

    A6 to A3 (5-1/2" x 8-1/2" to 11" x 17") For best results, use only paper recommended by SHARP. * For paper weighing from 105 to 128 g/m x 11") is the maximum size that can be fed through the bypass tray.
  • Page 83 Maximum height line Loading paper in paper trays 1 and 2 Gently lift and pull out the paper tray. Only use paper within the Sharp specification and follow the paper manufacturer’s instructions regarding fanning and loading the paper. The tray holds 500 sheets of paper.
  • Page 84 PAPER Paper size indicator Left guide Front guide Maximum height line 216x330 Paper size card Changing the copy paper size in the tray Gently lift and pull out the paper tray until it stops. Adjust the paper size indicator to match the paper size to be set.

  • Page 85: Adding Toner

    When any caution label is attached to the new toner cartridge,read it carefully and remove it. For best copying results, be sure to use only Sharp products. The package of Sharp toner has the Genuine Supplies label. GENUINE SUPPLIES...
  • Page 86 ADDING TONER Sealing tape Place the new toner cartridge with the tabs in the notches as shown. Slide the toner cartridge along the guides over the toner hopper. Hold the toner cartridge with one hand while pulling on the sealing tape to remove it. Tap on the top of the toner cartridge 5 times to start the flow of toner into the toner hopper.

  • Page 87: Used Toner Disposal

    Keep the full toner collecting container until the next regular service call. Your authorised Sharp Service Technician will collect the container for disposal. Install a new toner collecting container until it clicks into place.

  • Page 88: Storage Of Supplies

    Sharp toner has the Genuine Supplies label. Photoconductive drum The AR-287/AR-337/AR-407 Copiers have advanced process control technology which improves copy quality uniformity. This feature stabilizes copy quality throughout the life of the photoconductive drum by automatically compensating for the changes in drum charac- teristics due to wear, operator use patterns, and environmental conditions.

  • Page 89: Copier Trouble

    CHAPTER 5 COPIER TROUBLE? This chapter describes how to remove misfed originals and paper and other common trouble remedies. Page MISFEED REMOVAL ... 5-2 MAINTENANCE REQUIRED ... 5-11 TROUBLESHOOTING ... 5-12...

  • Page 90: Misfeed Removal

    MISFEED REMOVAL When a misfeed occurs, the copier will stop. The message “A MISFEED HAS OCCURRED. CLEAR INDICATED AREA. PRESS INSTRUCTIONS.” will appear with a display of paper misfeed locations. Press the INFORMATION ( for more detailed information as necessary. P.
  • Page 91 A MISFEED HAS OCCURRED. CLEAR INDICATED AREA. PRESS FOR RECOVERY INSTRUCTIONS. Feeding roller cover Exit roller cover Misfeed in the RADF When the RADF misfeeds an original sheet, the copier will stop and the misfeed message will appear. An original misfeed may occur at one of three locations: (A) in the RADF feed section, (B) in the exit roller, or (C) under the transport belt.
  • Page 92 MISFEED REMOVAL A MISFEED HAS OCCURRED. CLEAR INDICATED AREA. PRESS FOR RECOVERY INSTRUCTIONS. Misfeed in the bypass tray Gently pull the misfed paper out. Open and close the front cover to cancel the misfeed display.
  • Page 93 A MISFEED HAS OCCURRED. CLEAR INDICATED AREA. PRESS FOR RECOVERY INSTRUCTIONS. Misfeed in paper trays 1 and 2 Open the right side cover. Hold the handle and gently open the cover. If any paper is set in the bypass tray, remove the paper and close the bypass tray before opening the right side cover.
  • Page 94 MISFEED REMOVAL A MISFEED HAS OCCURRED. CLEAR INDICATED AREA. PRESS FOR RECOVERY INSTRUCTIONS. Transport lever Roller rotating knob Paper guide Misfeed in the transport area Open the front cover. Remove the misfed paper. Turn the transport lever to the left. CAUTION The area behind the transport lever is hot.
  • Page 95 Transport lever A MISFEED HAS OCCURRED. CLEAR INDICATED AREA. PRESS FOR RECOVERY INSTRUCTIONS. Turn the transport lever back into place. Close the front cover. Confirm that the misfeed display is cleared. Misfeed around the fusing unit and exit area NOTE: If an optional finisher (AR-FN1N) is fitted, please refer to chapter 7 Optional Equipment for additional misfeed removal help.
  • Page 96 MISFEED REMOVAL Roller rotating knob B Fusing unit tab Roller rotating knob C Exit area lever C Remove the misfed paper. If the misfed paper is in the inner part of the exit area: Turn roller rotating knob remove the paper. If the misfed paper is deep in the fusing unit, lift the fusing unit tab and remove any misfed paper.
  • Page 97 A MISFEED HAS OCCURRED. CLEAR INDICATED AREA. PRESS FOR RECOVERY INSTRUCTIONS. Paper guide Roller rotating knob D Close the front cover. Confirm that the misfeed display is cleared. Misfeed in the duplex module NOTE: If the optional finishers (AR-FN1N, AR-FN2) is fitted, please refer to chapter 7 Optional Equipment for additional misfeed removal help.
  • Page 98 MISFEED REMOVAL Paper feed area open/close lever 5-10 Remove the misfed paper from the section below the exit area. Close the exit area cover. Open and close the front cover to cancel the misfeed display. If the misfed paper is in the right side of the duplex module: Open the right side cover.

  • Page 99: Maintenance Required

    MAINTENANCE REQUIRED When the message “READY TO COPY. (MAINTENANCE REQUIRED)” appears in the message display, service by an authorised Sharp Service Technician will be required soon. Contact your Service Centre as soon as possible. 5-11...

  • Page 100: Troubleshooting

    TROUBLESHOOTING Always check the message display whenever the copier stops or operation is not possible. The messages will give you easy-to-follow directions. If the messages do not give specific instructions, check the list below. Problem Copier does not operate. Copies are too dark or too light.

  • Page 101: Troubleshooting

    (error code No. 53: only with AR-FN2) If a problem persists after checking the above, please consult your key operator prior to contacting your authorised Sharp Service Centre. Self-diagnostic function An automatic self-diagnostic function is built into this copier. Should the copier malfunction, the self-diagnostic function will locate the problem and stop the copier to prevent damage.

  • Page 103: General Information

    CHAPTER 6 GENERAL INFORMATION This chapter describes general information for using this copier. Page PART NAMES AND FUNCTIONS ... 6-2 Exterior ... 6-2 Interior ... 6-3 Operation panel ... 6-4 Touch panel (Basic screen) ... 6-5 USER MAINTENANCE ... 6-6 TOUCH PANEL CONTRAST ADJUSTMENT ...

  • Page 104: Part Names And Functions

    PART NAMES AND FUNCTIONS Exterior Exit area cover Open to remove misfed paper. Power switch Press to turn copier power on and off. Exit tray (optional) Finished copies are deposited in the exit tray. Operation panel All copier controls are located here for easy operation.

  • Page 105: Interior

    Interior Bypass tray paper guides Adjust to the width of the copy paper. Bypass tray Special papers (including transparency film) and copy paper can be fed from the bypass tray. Fusing unit The fusing unit is hot. Exercise care in this area. Transport lever Turn to open the transport section.

  • Page 106: Operation Panel

    PART NAMES AND FUNCTIONS Operation Panel PRINT COPY The key and indicators are not used for the copier features. LCD touch panel Displays information to assist the operator. Various operation keys are included in the touch panel depending on the particular screen being displayed.

  • Page 107: Touch Panel (Basic Screen)

    Touch Panel (Basic screen) CUSTOM SETTINGS ( ) key Press to set key operator programs or adjust the contrast of the touch panel. 2-SIDED COPY key Press to select the 1-sided to 1-sided, 1-sided to 2-sided, 2-sided to 1-sided or 2-sided to 2-sided copy mode.

  • Page 108: User Maintenance

    USER MAINTENANCE The document glass and the document cover (RADF transport belt) must be kept clean to avoid dirty areas from being copied onto the copies. Document glass and document cover Wipe the document glass and the document cover (RADF transport belt) with a soft, clean cloth. If necessary, dampen the cloth with water.

  • Page 109: Touch Panel Contrast Adjustment

    TOUCH PANEL CONTRAST ADJUSTMENT The contrast of the touch panel can be adjusted as below. ETTINGS DISPLAY KEY OPERATOR CONTRAST PROGRAMS TTINGS ONTRAST LIGHTER DARKER DARKER Press the CUSTOM SETTINGS ( Press the “DISPLAY CONTRAST” key on the touch panel. Press the “LIGHTER”...

  • Page 110: Specifications

    Output: 2 levels (normal copying) Local voltage ±10% (For this copier’s power supply requirements, see the name plate located on the left hand side at the rear corner of the copier.) AR-407 40 copies/min. (A4 (8-1/2" x 11")) 27 copies/min.
  • Page 111 (14 to 29 lbs.) for B4 and A3 (8-1/2" x 14" and 11" x 17") (14 to 20 lbs.)) or 5 mm or 3/16" (80 to 128 g/m (15 lbs. to 28 lbs.) SPECIFICATIONS AR-407 1292 mm (W) x 700 mm (D) (50-7/8" (W) x 27-9/16" (D)) 600 mm (W) x 700 mm (D) x 750 mm (H) (23-5/8"...

  • Page 113: Optional Equipment

    CHAPTER 7 OPTIONAL EQUIPMENT This chapter describes operating instructions for the Finisher (AR-FN1N, AR-FN2), Large Capacity Tray (AR-LC1N), Stand/500-sheet Paper Drawer (AR-DE1N) and Dual Tray Output Unit (AR-TR1). Page SYSTEM CONFIGURATION ... 7-2 FINISHER (AR-FN1N) ... 7-3 Part names ... 7-3 Specifications ...

  • Page 114: System Configuration

    Network scanner expansion kit (AR-NS1) Tandem - connection cable (AR-CA1) Data security kit 1 (AR-FR1 for the AR-287/AR-337)* Data security kit 2 (AR-FR2 for the AR-407)* * These equipments may not be avilable in some regions. 500-sheet paper drawer (AR-CS1)

  • Page 115: Finisher (Ar-Fn1N)

    FINISHER (AR-FN1N) The copier has two different finisher modes: one sorts copies into sets matching the sequence of the originals and the second groups copies by original. When the optional finisher (AR-FN1N) is installed, the copier can automatically staple the sorted copies. Each collated set of copies or group of copies can be stacked offset from the previous set.

  • Page 116: Offset Stack

    FINISHER (AR-FN1N) Offset stack OUTPUT TOP TRAY OFFSET TRAY OFFSET AUTO AUTO In the initial setting, the offset tray will move from side to side so that each copy set is offset by approximately 30 mm (1.2 inch). When the offset stack function is disabled, the offset tray will not move from side to side.

  • Page 117: Sort And Group

    Sort and group When SORT is selected, the SORT ( copies will be collated by sets. When STAPLE SORT is selected, the STAPLE SORT ( be indicated and collated copies will be stapled automatically. When the SORT or STAPLE SORT icon is not indicated on the touch panel, copies will be grouped by originals.

  • Page 118: Staple Sort

    FINISHER (AR-FN1N) Staple sort The STAPLE SORT mode staples A4, A4R, B4, and A3 (8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 14", and 11" x 17") size copies. Stapled sets cannot be delivered to the top tray. NOTE: Different size originals cannot be copied onto copy paper of their respective sizes in the STAPLE SORT mode.
  • Page 119 OPY.(DOCUMENT FEEDER MODE) STAPLE SORT SORT GROUP READY TO COPY. (DOCUMENT FEEDER MODE) OUTPUT TOP TRAY STAPLE OFFSET SORT SORT GROUP TRAY AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO INTERRUPT CLEAR AUDIT CLEAR PROGRAM INTERRUPT CLEAR ALL START CLEAR Select the desired stapling position.
  • Page 120 FINISHER (AR-FN1N) Stapling position AUTO EXPOSURE READY TO COPY. OUTPUT TOP TRAY STAPLE OFFSET SORT SORT GROUP TRAY OFFSET AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO OPY. STAPLE SORT SORT GROUP Using the document glass Set the original on the document glass with the corner to be stapled to the upper right.
  • Page 121 READY TO COPY. OUTPUT TOP TRAY STAPLE OFFSET SORT SORT GROUP TRAY AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO INTERRUPT CLEAR AUDIT CLEAR PROGRAM INTERRUPT CLEAR ALL START CLEAR PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END]. READ-END AUTO AUTO A4...

  • Page 122: Staple Cartridge Replacement

    FINISHER (AR-FN1N) Staple cartridge replacement The message “SLIDE THE FINISHER AWAY FROM THE COPIER AND ADD STAPLES.” will appear when the staple cartridge is empty. Replace the staple cartridge as follows: 7-10 While holding the finisher release lever, slide the finisher away from the copier.
  • Page 123 Insert the new staple cartridge into the box until it clicks in place. Insert the new cartridge by aligning the arrows on the cartridge with those on the box. Check that the cartridge locks in place by pulling it slightly. The cartridge holds 5,000 staples.

  • Page 124: Staple Jam Removal

    FINISHER (AR-FN1N) Staple jam removal If staples become jammed in the stapler, “CHECK STAPLER POSITION OR STAPLE JAM.” will be displayed. Remove the jammed staples in the manner described below. 7-12 While holding the finisher release lever, slide the finisher away from the copier.
  • Page 125 Return the lever to its original position. Insert the staple box to the stapler unit until it clicks in place. Return the stapler unit to face down. Push the finisher toward the copier and latch it in place. FINISHER (AR-FN1N) 7-13...

  • Page 126: Misfeed Removal

    FINISHER (AR-FN1N) Misfeed removal The copier will stop when a misfeed occurs. The message “A MISFEED HAS OCCURRED. CLEAR INDICATED FOR RECOVERY INSTRUCTIONS.” will appear AREA. PRESS with a display of paper misfeed locations. Press the INFORMATION ) key for more detailed information as necessary. SF-S15 20-bin sorter A MISFEED HAS OCCURRED.
  • Page 127 If the misfed paper cannot be removed in step 2, open the cover of the paper feed area of the finisher. Remove the misfed paper. If the misfed paper cannot be removed in step 4, close the cover of the paper feed area and open the top cover. Remove the misfed paper.
  • Page 128 FINISHER (AR-FN1N) A MISFEED HAS OCCURRED. CLEAR INDICATED AREA. PRESS FOR RECOVERY INSTRUCTIONS. 7-16 Push the finisher toward the copier and latch it in place. Confirm that the misfeed display is cleared. Misfeed in the lower transport area While holding the finisher release lever, slide the finisher away from the copier.
  • Page 129 Open the paper transport area cover of the finisher. Use the transport area lever to open the transport. Remove the misfed paper. Close the transport. FINISHER (AR-FN1N) 7-17...
  • Page 130 FINISHER (AR-FN1N) Roller rotating knob 7-18 Remove the misfed paper. Remove the misfed paper from the paper transport area. If the misfed paper is not seen in the paper transport area, turn the roller rotating knob to feed the paper. Close the paper transport area cover.

  • Page 131: Finisher (Ar-Fn2)

    FINISHER (AR-FN2) The copier has two different finisher modes: one sorts copies into sets matching the sequence of the originals and the second groups copies by original. When an optional finisher (AR-FN2) is installed, the copier can automatically staple the sorted copies. Each collated set of copies or group of copies can be stacked offset from the previous set.

  • Page 132: Offset Stack

    FINISHER (AR-FN2) Offset stack OUTPUT TOP TRAY OFFSET TRAY OFFSET AUTO AUTO 7-20 In the initial setting, the top tray is selected. To select the offset tray, press the OUTPUT key and then the “OFFSET TRAY” key on the touch panel. If the offset tray is selected, each copy set will be offset by a minimum of 15 mm for A4 paper (61/64 inch for 8-1/2"...

  • Page 133: Sort And Group

    Sort and group When SORT is selected, the SORT ( copies will be collated by sets. When STAPLE SORT is selected, the STAPLE SORT ( be indicated and collated copies will be stapled automatically. When the SORT or STAPLE SORT icon is not indicated on the touch panel, copies will be grouped by originals.

  • Page 134: Staple Sort

    FINISHER (AR-FN2) Staple sort The STAPLE SORT mode staples A4 (8-1/2" x 11") size copies. Stapled sets cannot be delivered to the top tray. NOTE: Different size originals cannot be copied onto copy paper of their respective sizes in the STAPLE SORT mode. Only A4 (8-1/2" x 11") size paper can be selected in the STAPLE SORT mode.
  • Page 135 READY TO COPY. (DOCUMENT FEEDER MODE) OUTPUT TOP TRAY STAPLE OFFSET SORT SORT GROUP TRAY AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO INTERRUPT CLEAR AUDIT CLEAR PROGRAM INTERRUPT CLEAR ALL START CLEAR Press the “OK” key. Set the number of copies. If A4 (8-1/2"...
  • Page 136 FINISHER (AR-FN2) Stapling position AUTO EXPOSURE READY TO COPY. OUTPUT TOP TRAY STAPLE OFFSET SORT SORT GROUP TRAY AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO READY TO COPY. OUTPUT TOP TRAY STAPLE OFFSET SORT SORT GROUP TRAY AUTO AUTO A4 100% EXPOSURE...
  • Page 137 INTERRUPT CLEAR AUDIT CLEAR PROGRAM INTERRUPT CLEAR ALL START CLEAR PLACE NEXT ORIGINAL. PRESS [START]. WHEN FINISHED, PRESS [READ-END]. READ-END AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO Set the number of copies. If A4 (8-1/2" x 11") paper is not selected, press the “PAPER SELECT”...

  • Page 138: Staple Cartridge Replacement

    FINISHER (AR-FN2) Staple cartridge replacement The message “ADD STAPLES.” will appear when the staple cartridge is empty. Replace the staple cartridge as follows: STAPLE TEAR line 7-26 Open the stapler cover. Lift the green release lever and remove the staple cartridge from the stapler.

  • Page 139: Staple Jam Removal

    Staple jam removal The message “CHECK STAPLER POSITION OR STAPLE JAM” will appear either when the staple cartridge is empty or when there is a staple jam. Please proceed as follows. Open the stapler cover and remove the stapler cartridge by lifting the green release lever.

  • Page 140: Misfeed Removal

    FINISHER (AR-FN2) Misfeed removal A MISFEED HAS OCCURRED. CLEAR INDICATED AREA. PRESS FOR RECOVERY INSTRUCTIONS. 7-28 The copier will stop when a misfeed occurs. The message “A MISFEED HAS OCCURRED. CLEAR INDICATED FOR RECOVERY INSTRUCTIONS.” will appear AREA. PRESS along with a display of paper misfeed locations. INFORMATION ( ) key for more detailed information.
  • Page 141 Remove the misfed paper. Rotate the paper feed area cover as shown to open it. Remove the misfed paper. Open the paper guide and remove the misfed paper. Close the paper feed area cover and then close the top cover. Push the finisher toward the copier and latch it in place.

  • Page 142: Large Capacity Tray (Ar-Lc1N)

    LARGE CAPACITY TRAY (AR-LC1N) The large capacity tray provides the added convenience of having 3,000 additional sheets of A4 (8-1/2" x 11") paper available. NOTE: To install the large capacity tray, an optional stand/500-sheet paper drawer (AR-DE1N) or an equivalent stand must be installed. PART NAMES Paper tray control button Specifications...

  • Page 143: Loading Copy Paper

    When the button lamp goes out, pull the paper tray out. Do not pull the paper tray out before the button lamp goes out. Only use paper within the Sharp specification and follow the paper manufacturer’s instructions regarding fanning and loading the paper.

  • Page 144: Misfeed Removal

    LARGE CAPACITY TRAY (AR-LC1N) Misfeed removal A MISFEED HAS OCCURRED. CLEAR INDICATED AREA. PRESS FOR RECOVERY INSTRUCTIONS. Release lever Upper right side cover 7-32 The copier will stop when a misfeed occurs. The message “A MISFEED HAS OCCURRED. CLEAR INDICATED FOR RECOVERY INSTRUCTIONS.”...
  • Page 145 LARGE CAPACITY TRAY (AR-LC1N) Push the large capacity tray toward the copier and latch it into place. If misfed paper is not found in step 2, pull the tray out. When pulling the large capacity tray out, be sure to pull it out after the paper tray control button lamp goes out.

  • Page 146: Stand/500-Sheet Paper Drawer (Ar-De1N)

    STAND/500-SHEET PAPER DRAWER This optional stand with a paper tray provides the convenience of increased paper capacity for the copier and a greater choice of paper sizes readily available for copying. Even greater paper capacity and size flexibility are available when the stand is equipped with an optional auxiliary 500-sheet paper drawer (AR-CS1).

  • Page 147: Stand/500-Sheet Paper Drawer (Ar-De1N)

    STAND/500-SHEET PAPER DRAWER (AR-DE1N) Loading copy paper The method of loading of copy paper for the paper tray of the 500- sheet paper drawer is the same as for the paper trays in the copier. See page 4-3. The method of changing the copy paper size is also the same for the paper trays in the copier.

  • Page 148: Misfeed Removal

    STAND/500-SHEET PAPER DRAWER (AR-DE1N) Misfeed removal A MISFEED HAS OCCURRED. CLEAR INDICATED AREA. PRESS FOR RECOVERY INSTRUCTIONS. 7-36 The copier will stop when a misfeed occurs. The message “A MISFEED HAS OCCURRED. CLEAR INDICATED FOR RECOVERY INSTRUCTIONS.” will appear with AREA.

  • Page 149: Dual Tray Output Unit (Ar-Tr1)

    DUAL TRAY OUTPUT UNIT This optional unit can deliver interrupt copies to the lower exit tray. PART NAMES Upper exit tray (AR-TE1) Lower exit tray (AR-TE1) Upper exit tray (First tray) Ordinary (non-interrupt) copies are deposited in the upper exit tray. Lower exit tray (Second tray) Interrupt copies are deposited in the lower exit tray.

  • Page 150: Specifications

    DUAL TRAY OUTPUT UNIT (AR-TR1) Specifications 7-38 Exit tray capacity Upper tray : 250 sheets Lower tray : 100 sheets Paper size Upper tray : A6 to A3 (5-1/2" x 8-1/2" to 11" x 17") Lower tray : A5 to A3 (5-1/2" x 8-1/2" to 11" x 17") Paper weight Upper tray : 52 to 128 g/m Lower tray : 56 to 105 g/m...

  • Page 151: Key Operator's Guide

    CHAPTER 8 KEY OPERATOR’S GUIDE This chapter contains information on all of the programs used by the key operator. The programs allow the key operator to tailor many functions of the AR-287/337/407 for specific modes of operation. These programs can only be accessed after a key operator code number has been entered.

  • Page 152: Key Operator Code Number

    KEY OPERATOR CODE NUMBER A key operator code number must be registered before a key operator program can be used. The key operator must remember this number. Only this registered number will allow access to the key operator programs. EXIT CUSTOM SETTINGS DISPLAY KEY OPERATOR...
  • Page 153 KEY OPERATOR PROGRAMS OTHER FUNCTION SETTINGS KEY OPERATOR CODE NUMBER CHANGE. AE:3 EXPOSURE ADJUSTMENT. TONER SAVE MODE. ADD OR CHANGE EXTRA PRESET RATIOS. INTERRUPT CLEAR AUDIT CLEAR PROGRAM KEY OPERATOR PROGRAMS KEY OPERATOR CODE NUMBER CHANGE. INPUT A NEW CODE NUMBER AND PRESS [OK]. PRESENT 98765 16805...

  • Page 154: Key Operator Programs

    KEY OPERATOR PROGRAMS A complete list of all key operator programs is provided below. These programs can only be accessed by first entering the key operator code number. The key operator programs are grouped into four categories: account control, other function settings, timer settings, and enable/disable settings.
  • Page 155 Category Program Name Date Format Setting Date and Time Adjustment Rotation Copy Setting Size Setting for [EXTRA] Timer Settings Auto Power Shut-off Timer Auto Clear Setting Preheat Mode Setting Noise Level Reduce Mode Message Time Setting Enable/Disable Disabling of Auto Settings Paper Selection Disabling of Auto...
  • Page 156 KEY OPERATOR PROGRAMS Category Program Name Disabling of Stapler Disabling of Covers Mode Disabling of PC/Modem Access Disabling of Second Tray Output in Interrupt Disabling of Auto Power Shut-off Mode Disabling of Beep When Keys Touched Disabling of Bypass- Tray When Offset Tray Selected Other Programs Total Count...

  • Page 157: Using The Key Operator Programs

    EXIT CUSTOM SETTINGS DISPLAY KEY OPERATOR CONTRAST PROGRAMS AUTO AUTO A4 100% EXPOSURE PAPER SELECT COPY RATIO INTERRUPT CLEAR AUDIT CLEAR PROGRAM EXIT KEY OPERATOR PROGRAMS COPIER COPIER PDA/ZR PROGRAM LIST TOTAL COUNT. PRINTOUT. KEY OPERATOR PROGRAMS Using the key operator programs Press the CUSTOM SETTINGS ( Press the “KEY OPERATOR PROGRAMS”...
  • Page 158 KEY OPERATOR PROGRAMS KEY OPERATOR PROGRAMS COPIER MODE OTHER FUNCTION TIMER SETTINGS SETTINGS ENABLE/DISABLE ACCOUNT CONTROL SETTINGS KEY OPERATOR PROGRAMS ACCOUNT CONTROL AUDITING MODE. NUMBER OF COPIES PER ACCOUNT. RESETTING ACCOUNT. ACCOUNT NUMBER CONTROL. INTERRUPT CLEAR ALL START CLEAR Select the desired category on the touch panel. Example: To select the account control category, press the “ACCOUNT CONTROL”...

  • Page 159: Account Control

    ACCOUNT CONTROL The programs of this category are used to set the internal auditor functions. These programs can be selected by pressing the “ACCOUNT CONTROL” key and then selecting the desired program key. Auditing Mode This program is used to enable or disable the basic auditing mode. When disabled, the message in the display will be “READY TO COPY.”...

  • Page 160: Resetting Account

    KEY OPERATOR PROGRAMS Resetting Account This program is used to reset all audit accounts or to selectively reset individual accounts. When the “RESETTING ACCOUNT.” key is pressed, the following display will appear. Account Number Control This program is used to register accounts, delete accounts, change an account number, or print all account numbers.
  • Page 161 KEY OPERATOR PROGRAMS To register accounts Press the “ENTER” key. Enter a 5-digit account number (00001 to 99999) using the 10-key pad. Select a number different from the key operator code number. Press the “ENTER” key. If a number that is already registered is entered, the message “THIS NUMBER IS ALREADY USED.”...

  • Page 162: Account Limit Setting

    KEY OPERATOR PROGRAMS Account Limit Setting This program is used to set the maximum number of copies which can be made against a registered account number. When an optional printer expansion kit is installed, enabling of key operator program “RECORD COPY AND PRINT PER ACCOUNT” will disable the “ACCOUNT LIMIT SETTING”.

  • Page 163: Account Number Security

    Account Number Security This program is used to make it difficult for users to gain access to accounts by entering code numbers through trial and error. If this program is selected and an operator enters three successive invalid account numbers, the copier will not accept another number for one minute and the message “PLEASE SEE YOUR KEY OPERATOR FOR ASSISTANCE.”...

  • Page 164: Exposure Adjustment

    KEY OPERATOR PROGRAMS OTHER FUNCTION SETTINGS The programs of this category are used to adjust various settings of copier functions. These programs can be selected by pressing the “OTHER FUNCTION SETTINGS” key and then selecting the desired program key. Key Operator Code Number Change See page 8-2, KEY OPERATOR CODE NUMBER.

  • Page 165: Add Or Change Extra Preset Ratios

    Two extra preset copy ratios can be added within both the reduction range (25% to 99%) and the enlargement range (101% to 400% for the AR-407; 101% to 800% for the AR-287 and the AR-337). Only added preset copy ratios can be changed. The standard preset copy ratios are fixed in memory and cannot be changed.

  • Page 166: Initial Margin Shift Setting

    KEY OPERATOR PROGRAMS Initial Margin Shift Setting Set the initial margin shift value with this program. When the “INITIAL MARGIN SHIFT SETTING.” key is pressed, the following display will appear. Erase Width Adjustment Set the initial setting of the amount of the erase area with this program. When the “ERASE WIDTH ADJUSTMENT.”...

  • Page 167: Stream Feeding Mode

    Initial Status Setting The copier will assume the initial settings when it is turned on, when the CLEAR ALL ( ) key is pressed, or when the auto clear interval has elapsed after a copy run. Use this program to establish the initial settings.
  • Page 168 KEY OPERATOR PROGRAMS Staple Position Setting This program is used to select the initial stapling position for an optional finisher (AR-FN1N only). When the “STAPLE POSITION SETTING.” key is pressed, the following display will appear. Date Format Setting This program is used to set the initial date format for the date function. When the “DATE FORMAT SETTING.”...

  • Page 169: Rotation Copy Setting

    Date and Time Adjustment This program is used to adjust the date and time which will be used for printing date. When the “DATE AND TIME ADJUSTMENT.” key is pressed, the following display will appear. Rotation Copy Setting If this program is set, the image of originals will rotate when the orientation of the originals does not match that of the copy paper.
  • Page 170 KEY OPERATOR PROGRAMS Size Setting for [EXTRA] The paper sizes in the paper trays (except an optional large capacity tray) can be changed by the users. The copier senses the paper sizes with the paper size indicators in the paper trays. If a paper size indicator is set to [EXTRA] and this program is used, the copier can sense paper sizes as selected on the setting screen.

  • Page 171: Timer Settings

    TIMER SETTINGS The programs of this category are used to set the timers for some functions. These programs can be selected by pressing the “TIMER SETTINGS” key and then selecting the desired program key. Auto Power Shut-off Timer The auto power shut-off mode is a function to turn off the power automatically once a programmed length of time has elapsed without any copier operation after the last copy of a run is made or power is turned on.

  • Page 172: Preheat Mode Setting

    KEY OPERATOR PROGRAMS Preheat Mode Setting Preheat mode functions to control the power consumption by lowering the temperature of the fusing unit to a programmed level once a programmed length of time has elapsed without any copier operation after the last copy of a run is made or power is turned on. This function lowers user’s electricity bill, reduces waste of natural resources, and cuts down on environmental pollution.

  • Page 173: Message Time Setting

    Message Time Setting This program is used to adjust the length of time that messages are displayed in the range of 1 to 12 seconds in 1 second increments. When the “MESSAGE TIME SETTING.” key is pressed, the following display will appear. KEY OPERATOR PROGRAMS KEY OPERATOR PROGRAMS MESSAGE TIME SETTING.

  • Page 174: Disabling Of Auto Paper Selection

    KEY OPERATOR PROGRAMS ENABLE/DISABLE SETTINGS The programs of this category are used to enable or disable some functions. These programs can be set or cancelled by pressing the check box of each program. Disabling of Auto Paper Selection This program is used to prevent automatic paper selection. When disabled, the copier will not automatically select a paper tray containing paper that matches the size of the original placed on the document glass or in the document feeder.

  • Page 175: Disabling Deletion Of Job Programs

    Disabling Deletion of Job Programs This program is used to prevent stored programs from being replaced or deleted. If this program is set, storing of job programs is also disabled. Disabling of Document Feeder This program is used to prevent the use of the document feeder when it malfunctions.

  • Page 176: Disabling Of Stapler

    KEY OPERATOR PROGRAMS Disabling of Stapler This program is used to enable or disable the stapler of the optional finisher (AR-FN1N, AR-FN2). If the stapler malfunctions, it can be disabled to prevent further malfunction or possible damage to the stapler until it is serviced. Disabling of Covers Mode This program is used to prevent selection of the COVERS mode.
  • Page 177 Disabling of Second Tray Output in Interrupt This program is used to disable output of copies to the second tray in interrupt copying for an optional dual tray output unit (AR-TR1). Disabling of Auto Power Shut-off Mode The auto power shut-off mode is used to turn off the power automatically once a programmed length of time has elapsed without any copier operation after the last copy of a run is made or power is turned on.

  • Page 178: Total Count

    KEY OPERATOR PROGRAMS Disabling of Bypass-Tray When Offset Tray Selected This program is used to disable the use of the bypass tray when the offset tray is selected for an optional finisher (AR-FN2 only). OTHER PROGRAMS The following two programs are not included in the four categories. The programs can be selected by pressing the relevant key on the touch panel after the key operator program mode is selected.

  • Page 179: Key Operator Assistance Call

    If the trouble cannot be easily remedied, use key operator program “DISABLING OF STAPLER” (page 8-26) to prevent the use of the stapler. Contact your authorised Sharp Service Centre for service. Contact your authorised Sharp Service Centre for service. (This message will appear when an optional finisher (AR- FN1N, AR-FN2) malfunctions.)
  • Page 180 MEMO 8-30...

  • Page 181: Key Operator Code Number: Factory Setting

    KEY OPERATOR CODE NUMBER: FACTORY SETTING The following is the factory setting of the Key Operator Code Number, which must be used to access the Key Operator Program. Factory setting = 00000 This number must be entered when accessing the Key Operator Program for the first time.
  • Page 182 2000C DSC1 CINSE1954FC51...
  • Page 183 Required in IEC-950 (EN 60 950) - Europe • The equipment should be installed near an accessible socket outlet for easy disconnection. Required in Appendix ZB of BS 7002 (En 60 950) — United Kingdom MAINS PLUG WIRING INSTRUCTIONS The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable (moulded) or a rewireable type.
  • Page 184 AR-287/AR-337/AR-407 SHARP ELECTRONICS (U.K.) LTD. Sharp House, Thorp Road, Newton Heath, Manchester M40 5BE SHARP CORPORATION PRINTED IN JAPAN 2000C DSC1 CINSE1954FC51...

This manual is also suitable for:

Ar-287Ar-337

Table of Contents