Table of Contents
Advertisement
Installation
E
N
G
L
I
S
Preparation
H
39
Cautions:
¡ ¡ Please follow the laws and regulations of your
province or country for installation of the unit.
¡ ¡ When bending the mounting tab of the mounting
collar with a screwdriver, be careful not to injure
your hands and fingers.
¡ ¡ We strongly recommend you to wear gloves for
installation work to protect yourself from injuries.
¡Before installation, check the radio operation with anten-
na and speakers.
¡Disconnect the cable from the negative (–) battery termi-
nal (see caution below).
¡The unit should be installed in a horizontal position with
the front end up at a convenient angle, but not more than
30°.
30° or less
Caution: Do not disconnect the battery terminals of a
car with trip or navigational computer since all user set-
tings stored in memory will be lost. Instead take extra
care with installing the unit to prevent shorts.
Transportation bracket
removal
Be sure to remove the transportation brackets
before use (installation).
Use binding-head screws ( 5
mm
ø x 6 mm) for
installation.
(a
page 52)
Be careful not to lose these screws.
48
CQ-VA7800N
Dashboard Installation
Installation Opening
The unit can be installed in any dashboard having an open-
ing as shown at right. The dashboard should be 4.5 mm - 6
mm thick in order to be able to support the unit.
53 mm
182 mm
Installation Precautions
This product should be installed by a professional
installer.
In case of difficulty, please contact the shop where you
purchased this product.
1. This system is to be used only in a 12-volt, DC battery
system (car) with negative ground.
2. Follow the electrical connections carefully
(a
66). Failure to do so may result in damage to the unit.
3. Connect the power lead after all other connections are
made.
4. Be sure to connect the battery lead (yellow) to the posi-
tive terminal (+) of the battery or fuse block (BAT) termi-
nal.
5. Insulate all exposed wires to prevent short circuiting.
6. Secure all loose wires after installing the unit.
7. Please carefully read the operating and installation
instructions of the respective equipment before connect-
ing it to this unit.
Binding-Head Screws
(5
ø x 6 mm)
mm
Binding-Head Screws
(5
ø x 6 mm)
mm
Transportation
Transportation
Bracket
Bracket
For Installation
No.
Item
q
Trim Plate
w
Mounting Collar
e
Mounting Spring
r
Mounting Bolt (5
Binding-Head Screw
t
(5
ø x 6 mm)
mm
Flat-Head Screw
y
(5
mm
ø x 6 mm)
Binding-Head Screw
u
(4
ø x 3 mm)
mm
page 56-
i
Spacer
Double-Faced Adhesive Tape
o
(for spacer)
Binding-Head Screw
!0
(5
ø x 8 mm)
mm
For Wiring
No.
Item
@0
Power Connector
Reverse Extension Cord
@1
(for rear view camera)
@2
Clip Connector
Display Unit/Hide-away Unit
@3
Connecting Cord
@4
ISO Antenna Adapter
Supplied Hardware
Diagram
Q'ty
No.
Tapping Screw
!1
1
(6
ø x 20 mm)
mm
Hex. Nut (5
1
!2
(for mounting bracket)
2
!3
Mounting Bracket
ø )
1
!4
Base Bracket
mm
Double-Faced Adhesive Tape
2
!5
(for hide-away unit)
4
!6
Velcro Tape
Tapping Screw (5
4
!7
mm) (for rear of the unit)
Hex. Nut (5
2
!8
(for rear of the unit)
1 set
!9
Rear Support Strap
4
Diagram
Q'ty
1
1
1
1
1
E
N
G
L
I
S
H
40
Item
Diagram
Q'ty
4
ø )
mm
4
2
2
2
2
mm
ø x 16
1
mm
ø)
1
1
49
CQ-VA7800N
Advertisement
Table of Contents
