On Screen Messages - Panasonic Viera TX-P42G10B Operating Instructions Manual

On screen messages

Message
All tuning data will be erased
Are you sure ?
Are you sure you want to delete this timer ?
Press OK to delete timer
Press RETURN to return
Bad signal
Child Lock is active !
Press OK to enter PIN.
Ethernet cable not connected
Faulty dish
Feature not available
Found new software version
Press OK to start update
(may take 40 mins)
or Press EXIT to ignore
and you can update when TV is in standby.
Gateway does not answer.
Please confirm connection and setting of
router.
Invalid operation - Please check settings
and connections.
Invalid system time. Please exit !
IP address conflict
IP address not set
Manual IP setting not correct
Max. number of Timers already set !
New channels found!
Press OK to update channel list
Press EXIT to ignore.
No channel found.
Please check aerial or local signal
availability.
Press OK to start Auto Setup.
No module inserted
No recording - Check media
No recording - Already recording
No recording - Unknown reason
No service
No signal
76
●
"Shipping Condition" will erase all tuning data (p. 49).
●
Confirm correct operation.
●
Confirm correct operation.
●
The signal is weak. Check the aerial is plugged in properly. It may
be necessary to have an aerial installer check the signal and aerial
alignment.
●
Reset channels. (p. 34 and p. 35)
●
The selected channel is locked in Child Lock (p. 45). You must enter the
PIN number before the channel will be displayed.
●
Check the connection of the LAN cable. If you use a hub, also check the
light on the hub is lit.
●
The LAN cable might be defective.
●
The satellite cable might be short-circuited or there might be connection
problems of the cable. Check the cable and connection and then turn the
TV Off with the Mains power On / Off switch, and turn it On again.
●
If the message still persists, it may be necessary to have a dish installer
check the dish and cable.
●
It is not possible to record from COMPONENT, HDMI or PC. Connect the
recorder to the TV using a fully wired SCART cable for recording from the
TV tuner.
●
Confirm Q-Link or VIERA Link settings (p. 58 - 61).
∗∗∗
.
●
There is a new software available.
●
A connection failure has occurred and the gateway is not responding.
Check the settings and connections of the router.
●
Turn the TV and the router Off with the Mains power On / Off switch, and
turn them On again.
●
Check the Q-Link or VIERA Link connection and setting (p. 58 - 61).
●
Cannot get the time information. Check the connection of the RF cable.
●
Duplicate IP address has been detected. Check the IP address of other
equipment such as computers, routers and ensure that there are no
duplicate IP address.
●
An IP address is required to use interactive content through the internet.
Enter an IP address.
●
The system is unable to set the IP address. Consult your Internet Service
Provider or telecommunications company.
●
The maximum number of timer programming events is 15.
●
There may be new channels available.
●
This message will appear each time a change is made by the
broadcasters. This message can be deactivated by setting "New Channel
Message" to Off in "DVB Tuning Menu".
Selecting OK will perform "Update Channel List".
●
Please follow the message.
If it is still failed, consult your local Panasonic dealer.
●
Check the CI module inserted completely (p. 51).
●
The tape or disc may be "write protected", missing or damaged.
●
The equipment may already be recording.
●
The recording may not be performed. Check the equipment.
●
Disc or tape may be full.
●
The broadcaster has stopped the service. Check the channel in the TV
Guide. (p. 18 and p. 19)
●
The TV cannot detect the signal. Check the connection of the RF cable.
Meaning / Action