Related Manuals for Panasonic WV-BS500
Summary of Contents for Panasonic WV-BS500
- Page 1 Combination Camera WV-BS500 WV-CS600A WV-BS504E WV-CS604E WV-BST500 WV-CSR600 WV-CST600 Before attempting to connect or operate this product, please read these instructions completely...
- Page 2 If you lose the fuse cover the plug must not be used until a replacement REFER SERVICING TO QUALIFIED SERVICE cover is obtained. A replacement fuse cover can be purchased from your local Panasonic PERSONNEL. Dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE...
-
Page 4: Table Of Contents
CONTENTS PREFACE ............Self Return Setting ........17 FEATURES ............Auto Mode Setting ........17 PRECAUTIONS ..........LOCAL/REMOTE Setting ......18 CONSTRUCTION ..........Camera Setting ........... 18 SETUP PROCEDURE ........INSTALLATION ..........30 Setup Menu ..........CONNECTIONS ..........33 Setup Menu Description ......SYSTEM CONNECTIONS ........ -
Page 5: Preface
PRECAUTIONS CS600A, WV-CS604E, WV-CSR600 CST600 (46 dB for WV-BS500, WV-BS504E and • Do not attempt to disassemble this unit. There WV-BST500). With its advanced digital signal are no user serviceable parts inside. Refer processing circuit, it is equipped to handle the servicing to qualified service personnel. -
Page 6: Construction
(6) Fall Prevention Wire (2) Video Output Connector (7) Decoration Cover (3) Power Cable for WV-CS600A, WV-CSR600, (8) Cooling Holes WV-CST600, WV-BS500, and WV-BST500 (9) Dome Cover (3*) Power Cable for WV-CS604E and WV-BS504E (4) Camera Mounting Angle (5) Panning Start Point... -
Page 7: Setup Procedure
SETUP PROCEDURE Setup Menu This camera utilizes a user setup menu that is displayed on-screen. Setup Menu This setup menu contains various sub menus that form a tree-type structure as shown below. This menu is described in the "SETUP MENU DESCRIPTION". CAMERA SET UP MENU Preset... - Page 8 Note: The menus described in bold are displayed only when WV-CSR600 is used. UNIT TRANSMISSION DATA PARITY STOP XON/ WAIT ALARM DELAY NUMBER SPEED XOFF TIME DATA TIME Local/ Camera Remote Menu White Shutter Sensitivity Sync. Wide Motion Balance Speed ON/OFF INT/LL Dynamic...
-
Page 9: Setup Menu Description
Setup Menu Description RS485 site communication (only WV-CSR600) Communication parameters • Full/Half duplex (page 30) • Transmission speed (2400 - 19200 bps) (page 11) • Parity check, Stop bit, Characters, Flow control (page 11) • Retransmit time, Delay time, Alarm output (page 11) •... - Page 10 AUTO MODE AUTO MODE is for setting the movement of the camera. You can select from three automatic operation modes and one manual operation mode as follows: OFF mode: No automatic operation. The camera can be operated only manually. SEQ mode: The camera operates in the sequence of preset positions in numerical order. SORT mode: The camera operates in the sequence of preset positions counterclockwise from Pan/Tilt Starting Point.
- Page 11 Note: The result of field setup of the mask area and level adjustment is fed back (effected) to the lens iris control in ALC mode. (3) Shutter Speed (SHUTTER) You can select the shutter speed from 1/50 (OFF), 1/120, 1/250, 1/500, 1/1000, 1/2000. 1/4000, and 1/10000 second.
-
Page 12: Setting Procedures
• ATW (Auto Tracing White Balance) In this mode, the colour temperature is monitored continuously and thereby white balance is set automatically. The colour temperature range for the proper white balance is approximately 2,600-6,000K. Proper white balance may not be obtained under the following conditions: 1. -
Page 13: Menu Display
Menu Display D4 menu Setup Menu Display Camera Set Up Menu Exit 1. Select the number of the camera you want to set up and a monitor to F3 F4 display the SET UP MENU. Camera Set Up Menu 2. Display the D4 menu on the LCD by pressing the appropriate cursor Res A.Res Exit buttons. - Page 14 The following communication parameters can be set: UNIT NUMBER Specifies the camera ID numbers in case more than two cameras and WV-RM70 controllers are daisy chain connected. Select (1-32), (33-64) or (65-96) with the dip switch. The factory setting is 1. BAUD RATE Specifies the transmission speed (2400, 4800, 9600, 19200 bps).
-
Page 15: Preset
Preset Preset Menu Display 1. Displaying the preset menu directly (1) Move the cursor to PRESET 1 and move the joystick to the left or right to select the position number to be set. (2) Press the CAM (SET) key. The preset menu appears on the monitor screen. - Page 16 3. To set the lens zoom and focus positions Position setting menu Move the cursor to PUSH SET next to ZOOM/FOCUS and press the CAM (SET) key. The setting screen appears. POSITION 15*H Select a zoom position by moving the joystick up and down, and a PAN/TILT PUSH SET focus position by moving it to the right and the left, and then press the...
- Page 17 (2) To copy a preset ID from another position Move the cursor to COPY and press the CAM (SET) key. The PRESET NO.15*H preset ID in the immediately preceding position is shown. Each 0123456789 ABCDEFGHIJKLM consecutive operation of the CAM (SET) key displays the ID NOPQRSTUVWXYZ ().,'":;&#!?= preceding the one currently displayed.
- Page 18 Light Control Setting Preset setting menu 1. Move the cursor to ALC/MANUAL and move the joystick to the left or right to select ALC or MANUAL. PRESET NO.15*H ALC: The lens iris is automatically adjusted to suit the brightness of POSITION SET PRESET ID the object.
-
Page 19: Deleting Preset Positions
To return to the PRESET NUMBER SET Menu Preset setting menu • Move the cursor to RET and press the CAM (SET) key. The PRESET NUMBER SET menu appears with the * mark on the right of the preset PRESET NO.15*H position number. -
Page 20: Self Return Setting
Self Return Setting Setup menu • To set a time-out parameter for return to the home position *** SET UP MENU *** Move the cursor to SELF RETURN and select a return time by moving PRESET 1* the joystick to the left or right. Return time changes as follows: MAP* HOME POSITION SELF RETURN... -
Page 21: Local/Remote Setting
5. To set endless turn ON/OFF Move the cursor to ENDLESS, and move the joystick to the left or right ** AUTO PAN ** to set endless turn ON or OFF. POSITION START ON: The camera pans from the start position to the end position, then SPEED ...I.. - Page 22 2. Camera Identification Setting (CAMERA ID) ** SET UP ** CAMERA ID OFF * • Move the cursor to CAMERA ID, and select ON (to display the camera ALC/MANUAL ALC * SHUTTER identification) or OFF by using the joystick. SENS UP SYNC WHITE BAL ATW *...
- Page 23 3. Light Control Setting (ALC/MANUAL) Camera setting menu • Display SET UP on the monitor screen. ** SET UP ** If necessary, refer to Setup Menu Display for details on displaying the CAMERA ID OFF * ALC/MANUAL ALC * SET UP on the monitor screen. SHUTTER •...
- Page 24 • If you want to change the video output level (picture contrast), move the cursor to LEVEL and use the joystick to adjust the iris of the ALC * ALC CONT * lens. When you move the cursor to the right (+) with the joystick, the BACK LIGHT COMP lens iris opens wider to raise the level of video output.
- Page 25 5. Gain Control Setting (AGC ON/OFF) Camera setting menu ** SET UP ** • Display SET UP on the monitor screen. CAMERA ID OFF * If necessary, refer to Setup Menu Display for details on displaying the ALC/MANUAL ALC * SHUTTER SET UP menu on the monitor screen.
- Page 26 • Supply the video output signal of the camera to be adjusted and the SYNC menu reference camera video output signal (for example, Camera 1) to a dual-trace oscilloscope. ** SYNC ** V PHASE • Set the dual-trace oscilloscope to the vertical rate and expand the COARSE 1(1---16) vertical sync portion on the oscilloscope.
- Page 27 Camera setting menu 8. White Balance Setting (WHITE BAL) (available only with WV-CS600A, WV-CS604E, WV-CSR600, or WV-CST600) ** SET UP ** CAMERA ID OFF * ALC/MANUAL ALC * (1) Auto-Tracing White Balance Mode (ATW) SHUTTER • Display SET UP on the monitor screen. SENS UP SYNC (Refer to Setup Menu Display for details on displaying the SET UP...
- Page 28 (2) Automatic White Balance Control Mode (AWC) Camera setting menu • Display SET UP on the monitor screen. ** SET UP ** (Refer to Setup Menu Display for details on displaying CAMERA ID OFF * the SET UP menu on the monitor screen.) ALC/MANUAL ALC * SHUTTER...
- Page 29 Camera setting menu 10. Motion Detector Setting (MOTION DET) ** SET UP ** • Display SET UP on the monitor screen. CAMERA ID OFF * (Refer to Setup Menu Display for details on displaying the SET UP ALC/MANUAL ALC * SHUTTER menu on the monitor screen.) SENS UP...
- Page 30 Because the alarm signal is multiplexed on the video signal it may be mistakenly interpreted by other video equipment as a time code signal. Therefore, when this camera is not used in a Panasonic Intelligent CCVE System, select OFF to prevent the above from occurring.
- Page 31 Camera setting menu 12. Special Menu (SPECIAL) ** SET UP ** This menu lets you adjust and set up the video signal of the camera to CAMERA ID OFF * meet your requirements. ALC/MANUAL ALC * SHUTTER • Display SET UP on the monitor screen. SENS UP (Refer to Setup Menu Display for details on displaying the SET UP on SYNC...
- Page 32 (5) To restore the camera default position Move the cursor to REFRESH by using the joystick and press the F2 ** SPECIAL ** button of the WV-CU550A. CHROMA GAIN ..I..(For the WV-RM70, keep pressing the Right and Left switches AP GAIN ..I..
-
Page 33: Installation
2. Setting the switches INSTALLATION Set the switches as follows: Precaution: The following installations should be made by DIP Switches qualified service personnel or system installers. Setting the camera switches (only for WV-CSR600) • To reset the communication parameters to the factory preset values, for example, when operating multiple cameras in a daisy chain connection, set the switches inside the camera... - Page 34 b. Top cable exit NTSC (EIA) PAL (CCIR) or NTSC (EIA) PAL (CCIR) Note: The dip switch is not for changing NTSC (EIA) to PAL (CCIR) or PAL (CCIR) to NTSC (EIA). This switch is set at factory. Do not change the setting of this switch.
- Page 35 4. Hook the Fall prevention wire on the camera 2. Follow the instructions given here to mounting angle. ensure that the camera and camera mounting angle are installed safely. 3. When removing the camera from the camera mounting angle, loosen and press up the camera fixing screw (M3) by using a screwdriver.
-
Page 36: Connections
CONNECTIONS Precaution: The following connections should be made by qualified service personnel or system installers. 220 - 240V AC WV-CS604E orWV-BS504E 24V AC Data cable (Only for WV-CSR600) RS485 cable Video Output Cable Coaxial Cable BNC Plug (5C - 2V) To Video IN (CAMERA IN) BNC Plug... - Page 37 • RS485 site connection Brown T (B) Data Transmission Orange T (A) Yellow R (B) Data Reception Green R (A) For daisy chain connection of multiple cameras, make sure to match each male connector with its female counterpart. Note: Use the cable that is described below for RS485 site communication by using WV-CSR600. •...
-
Page 38: System Connections
SYSTEM CONNECTIONS Combination Camera WV-CSR600 only Other models Max. 64 Cameras Matrix Switcher VTRs (up to 16) Personal Computer RS-232C Port CONTROL ALARM INPUT INPUT INPUT INPUT INPUT INPUT INPUT OUTPUT OUTPUT OUTPUT OUTPUT DATA VIDEO OUT1 VIDEO OUT1 VIDEO OUT1 VIDEO OUT1 VIDEO OUT1 VIDEO OUT1... -
Page 39: Prevention Of Blooming And Smear
PREVENTION OF BLOOMING AND SMEAR Smear Bright object When the camera is aimed at a bright light, such as a spotlight, or a surface that reflects bright light, smear or blooming may appear. Therefore, the camera should be operated carefully in the vicinity of extremely bright objects to avoid smear or blooming. - Page 40 Combination Camera (WV-BS500, WV-BS504E, WV-BST500) WV-BS500, WV-BS504E WV-BST500 AC 230 V, 50 Hz (WV-BS500) Power Source AC 230 V, 50 Hz AC 24 V, 50 Hz (WV-BS504E) Power Consumption Ambient Operating 10°C - +50°C Temperature Dimensions 130 (D) x 191 (H) mm 130 (D) x 195 (H) mm Approx.
-
Page 41: Accessories
Pan / Tilt Panning Range 360° Endless Panning Angle Setting Possible (in Auto-Pan mode) Panning mode Manual/Sequential Position/Sort Position/Auto Pan Manual : Approx. 3°/s - 120°/s eight steps Panning Speed Sequence Position : Maximum approx. 240°/s Tilting Range 0 - 90° Tilting Mode Manual/Sequential Position/Sort Position Manual : Approx. - Page 42 Matsushita Electric Industrial Co., Ltd. Central P.O. Box 288, Osaka 530-91, Japan N0397-0 YWV8QA4546AN Printed in Japan N 30 Gedruckt in Japan Imprimé au Japon Impreso en Japón...