Panasonic WV-CM2000 Operating Instruction page 6

21. Screen Control
This control is preset at the factory.
Do not adjust this control.
When the adjustment of this control is required, refer
to the qualified service personnel.
22. S-Video Input Connector (INPUT 4, S-VIDEO IN)
This connector accepts a S-Video (PAL/NTSC) signal.
23. S-Video Output Connector (INPUT 4, S-VIDEO OUT)
The S-Video input signal connected to the S-Video
Input Connector (22) is looped through to this connec-
tor.
24. S-Video Termination Switch (INPUT 4, 75 /Hi-z)
When bridging or looping through the S-Video signal,
set this switch to Hi-z position, and other cases this
switch should be set to 75 position.
25. Audio Input Connector (INPUT 4, AUDIO IN)
8 dB/Hi-z audio signal can be supplied to this input
connector.
26. Audio Output Connector (INPUT 4, AUDIO OUT)
The audio input signal connected to the Audio Input
Connector (25) is looped through to this connector.
27. S-Video Input Connector (INPUT 3, S-VIDEO IN)
This connector accepts a S-Video (PAL/NTSC) signal.
28. S-Video Output Connector (INPUT 3, S-VIDEO OUT)
The S-Video input signal connected to the S-Video
Input Connector (27) is looped through to this connec-
tor.
29. S-Video Termination Switch (INPUT 3, 75Ω/Hi-z)
When bridging or looping through the video signal, set
this switch to Hi-z position, and other cases this switch
should be set to 75 position.
30. Audio Input Connector (INPUT 3, AUDIO IN)
8 dB/Hi-z audio signal can be supplied to this input
connector.
31. Audio Output Connector (INPUT 3, AUDIO OUT)
The audio input signal connected to the Audio Input
Connector (30) is looped through to this connector.
32. Video Input Connector (INPUT 2, VIDEO IN)
This connector accepts a composite PAL/NTSC/M-
NTSC video signal.
33. Video Output Connector (INPUT 2, VIDEO OUT)
The video input signal connected to the Video Input
Connector (32) is looped through to this connector.
34. Video Termination Switch (INPUT 2, 75Ω/Hi-z)
When bridging or looping through the video signal, set
this switch to Hi-z position, and other cases this switch
should be set to 75Ω position.
35. Audio Input Connector (INPUT 2, AUDIO IN)
8 dB/Hi-z audio signal can be supplied to this input
connector.
36. Audio Output Connector (INPUT 2, AUDIO OUT)
The audio input signal connected to the Audio Input
Connector (35) is looped through to this connector.
37. Video Input Connector (INPUT 1, VIDEO IN)
This connector accepts a composite PAL/NTSC/M-
NTSC video signal.
38. Video Output Connector (INPUT 1, VIDEO OUT)
The video input signal connected to the Video Input
Connector (37) is looped through to this connector.
39. Video Termination Switch (INPUT 1, 75 /Hi-z)
When bridging or looping through the video signal, set
this switch to Hi-z position, and other cases this switch
should be set to 75 position.
40. Audio Input Connector (INPUT 1, AUDIO IN)
8 dB/Hi-z audio signal can be supplied to this input
connector.
41. Audio Output Connector (INPUT 1, AUDIO OUT)
The audio input signal connected to the Audio Input
Connector (40) is looped through to this connector.
42. Standby Input Connector (STAND BY IN)
Supply the control signal to select the Standby On/Off
mode to this connector.
Only when setting the Stand-by On/Off Switch to the
ON position, this control signal can be functioned.
When the coaxial cable from this connector is ground-
ed, the picture is appeared on the screen.
43. Standby Output Connector (STAND BY OUT)
This connector is looped through to the Standby Input
Connector(42).
44. Power Cord
CAUTION: The supplied power cord is designed for
use on the supplied 220-240V AC supply only.
-4-