Related Manuals for Panasonic WV-CM146
Summary of Contents for Panasonic WV-CM146
- Page 1 Colour Monitor WV-CM146 Before attempting to connect or operate this product, please read these instructions completely...
- Page 2 If you lose the fuse cover the plug must not be used until a replacement TO REDUCE THE RISK OF ELECTRIC SHOCK, cover is obtained. DO NOT REMOVE COVER (OR BACK), NO USER A replacement fuse cover can be purchased from your local Panasonic SERVICEABLE PARTS INSIDE. Dealer. REFER SERVICING TO QUALIFIED SERVICE IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCK- PERSONNEL.
-
Page 4: Table Of Contents
CONTENTS PREFACE ......................................2 FEATURES ......................................2 PRECAUTIONS ....................................2 MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ......................3 SETUP OPERATION ................................... 6 OPERATING PROCEDURES ................................11 CONNECTIONS ....................................15 SPECIFICATIONS ....................................18... -
Page 5: Preface
• Up to 8 solid state colour cameras can be connected • Do not attempt to disassemble the monitor. To prevent to Colour Monitor WV-CM146 with an alarm feature. (4 electric shock, do not remove screws or cover. There VP multiplexed cameras and 4 specified system cam- are no user-serviceable parts inside. -
Page 6: Major Operating Controls And Their Functions
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS FRONT VIEW QUAD POWER SEQUENCE 1/5 PUSH SET UP Video Monitor WV-CM STAND BY QUAD/SPOT CAMERA SEQ/VTR MIN. .MAX DISPLAY INPUT MONITOR V-HOLD COLOUR BRIGHT CONTRAST PICTURE AUDIO MODE SELECT MODE q Power Switch (POWER) SEQ/VTR: When the INPUT SELECT switch is set to "CAMERA,"... -
Page 7: Rear View
u Colour Control (COLOUR) !3 Picture Adjustment Turn this control clockwise to strengthen the picture Turn this control clockwise for a sharp picture. colour. Turn this control counterclockwise for a soft picture. Turn this control counterclockwise to weaken the pic- !4 Audio Control (AUDIO, MIN/MAX) ture colour. - Page 8 Specified System Cameras OUT) to these connectors. This connector supplies the timing pulse signals for Specified System Camera: Panasonic VD2 multi- switching in the sequence operation of other extensible plexed camera systems, such as another CCTV system or sequential @9 Camera Input Connectors (CAMERA INPUT 5/6/7/8, switcher.
-
Page 9: Setup Operation
SETUP OPERATION 1. SET UP MENU Make sure that the connection of cameras, peripherals, or alarm connectors is correct and firm. The SET UP MENU is not displayed if no camera is connected. (Refer to "CONNECTIONS" on page 15.) This menu is described in the following section 3 "SET UP MENU DESCRIPTION" in detail. Set the DISPLAY MODE switch to ON to display SET UP MENU. -
Page 10: Rec Mode
3-3. Timing Selection (TIMING SELECT) 3-6. Alarm Recording Mode Setting (ALARM REC MODE) ** SET UP MENU ** ** SET UP MENU ** CAMERA ID 1.34..7. CAMERA ID 1.34..7. 1 CAMERA 1 CAMERA AUDIO SELECT AUDIO SELECT TIMING SELECT TIMING SELECT ----- ---- -----... - Page 11 • All Reset Operation • Editing the SET UP MENU All reset helps you escape from confusion in set up To edit the SET UP MENU (resetting/re-adjustment,) menu operation. The steps to reset are follows: move the cursor to the bottom line using the Up/Down (1) Make sure that the DISPLAY MODE switch is set to switch, and move the cursor to "SET UP DISABLE"...
- Page 12 Setting Procedures 1-1. Move the cursor to "CAMERA ID," and select the desired camera using the Left (A) or Right switch (B). To display camera identification, press the SET UP switch. 1. Camera Identification Setting (CAMERA ID) 1-2. After completing item 1, move the cursor to the second line using the Down switch (C).
- Page 13 3. Timing Selection (TIMING SELECT) 5. Page Sequence (PAGE SEQ) ** SET UP MENU ** ** SET UP MENU ** CAMERA ID 1.34..7. CAMERA ID 1.34..7. 1 CAMERA 1 CAMERA AUDIO SELECT AUDIO SELECT TIMING SELECT TIMING SELECT ----- ---- ----- ---- PAGE SEQ...
-
Page 14: Operating Procedures
8. Automatic Reset On/Off Setting (AUTO OPERATING PROCEDURES RESET) Selection of Camera ** SET UP MENU ** CAMERA ID 1.34..7. QUAD POWER SEQUENCE 1/5 STAND BY QUAD/SPOT CAMERA SEQ/VTR 1 CAMERA MIN. .MAX AUDIO SELECT DISPLAY INPUT MONITOR V-HOLD COLOUR BRIGHT CONTRAST PICTURE... - Page 15 Sequence Mode Monitoring (more than Standby mode Monitoring picture two cameras) QUAD POWER STAND BY QUAD/SPOT SEQUENCE 1/5 CAMERA SEQ/VTR QUAD SEQUENCE 1/5 POWER STAND BY QUAD/SPOT CAMERA SEQ/VTR MIN. .MAX DISPLAY INPUT MONITOR V-HOLD COLOUR BRIGHT CONTRAST PICTURE AUDIO MODE SELECT MODE...
- Page 16 Press the desired camera selection switch. something wrong with this monitor. Caution: Unless recorded by WV-CM146 video tapes cannot be Recording on Time Lapse VTR played back in QUAD or SPOT monitor mode. Only tapes recorded by WJ-FS20 without VITC signal Set the time lapse VTR in recording mode.
- Page 17 C. VITC signal (option) The picture from the VTR are displayed on the monitor by Do not align this signal with ID-code of WV-CM146. The operating the MONITOR MODE switch and the INPUT VITC should be placed at 7H or 9H.
-
Page 18: Connections
(multiplexed VD camera) to be For example, the wire length limits an intercom system are connected with this monitor must be Panasonic models. If as follows ; cameras of other make are connected, this monitor will not... - Page 19 The polarities of the intercom system and the Spot Monitor Auto Reset Control In of the monitor should be matched. Check the polarities of the intercom system by tester (meter). This monitor has an auto reset circuit that resets automati- cally 60 seconds after the intercom or alarm sensor signal Mater Unit is supplied.
- Page 20 Intercom 5 - 8 Intercom 1 - 4 Main Unit Intercom 4 Ground Coaxial Cable Intercom 1 Intercom 2 Intercom 3 Colour Monitor WV-CM146 ALARM TIMING SELECT CONTROL SPOT MONITOR CONTROL IN Setup Menu Setting; RECOVER STDBY ALL GND RESET FOCUS...
-
Page 21: Specifications
SPECIFICATIONS Power Source: 220 - 240V AC 50 Hz Power Consumption: Approx. 110W CRT Size: 36.8 cm (14" diagonal) Actual Visual Size: 33.5 cm (13" diagonal) Camera Input: 1.0 V[p-p]/75 , composite 8 (BNC) (specified VP multiplexed camera x 4) Video Input: 1.0 V[p-p]/75 , composite 1 (BNC) - Page 22 Matsushita Electric Industrial Co., Ltd. Central P.O. Box 288, Osaka 530-91, Japan N1196-2027 YWV8QA4426CN Printed in Japan N 30 Gedruckt in Japan Imprimé au Japon Impreso en Japón...