Panasonic SC-VK62D Operating Instructions Manual page 29

Picture abnormal or un-viewable
Picture distorted.
Picture size doesn't fit the
screen.
The television may display
incorrectly or colors appear
faded.
Menu is not displayed
correctly.
Auto zoom function does not
work well.
The picture on the television
disappears or stripes appear
on the screen.
Progressive video
There is ghosting when
progressive output is on.
Picture not in progressive
output.
Listening to the radio
Noise is heard.
"ST" flickers or doesn't light.
Sound is distorted.
A beat sound is heard.
A low hum is heard during AM
broadcasts.
Unit displays
Although the unit is on standby
mode, the display lights up and
changes continuously.
The display is dark.
"NO PLAY"
"NO DISC"
"F61"
"DVD U11"
"ERROR"
"DVD HMM"
MM stands for a number.
Television displays
"This disc may not be played
in your region"
No on-screen display.
" "
"Cannot display group xx,
content xx"
Using the cassette deck
Poor quality sound.
Recording is not possible.
Memory reset (Initialization)
When the following situations occur, refer to the instructions below to reset the memory:
•
There is no response when buttons are pressed.
•
You want to clear and reset the memory contents.
To reset memory
1 Disconnect the AC power supply cord. (Wait at least 3 minutes before proceeding to step 2.)
2 While pressing and holding down [y y y y y /I] on the main unit, reconnect the AC power supply cord.
"– – – – – – – – – " appears on the display.
3 Release [y y y y y /I].
All the settings are returned to the factory preset.
You will need to reset the memory items.
•
Some distortion is normal during SEARCH.
•
Ensure that the unit is connected directly to the television, and is not connected through a video
cassette recorder.
•
Change "TV Aspect" in the "Video" tab.
•
Change the Zoom setting.
•
The unit and television are using different video systems.
Use a multi-system or NTSC television.
For Southeast Asia
Use a multi-system or PAL television.
For others
•
The system used on the disc does not match your television.
–
PAL discs cannot be correctly viewed on an NTSC television.
–
This unit can convert NTSC signals to PAL 60 for viewing on a PAL television ("NTSC Disc
Output" in "Video" tab.)
•
Restore the zoom ratio to "x1.00".
•
Set "Subtitle Position" in Display Menu to "0".
•
Turn off TV's zoom function.
•
Use the other preset aspect ratios or manual adjustment.
•
Zoom function may not work well, especially in dark scenes and may not work depending on
the type of disc.
•
Mobile telephone chargers can cause some disturbance.
•
If you are using a TV indoor antenna, change to an outdoor antenna.
•
The television antenna wire is too close to the unit. Separate the antenna wire of the television from the unit.
•
This problem is caused by the editing method or material used on DVD-Video, but should be
corrected if you use interlace output. Change "Video Output Mode" in Picture Menu to
"480i (or 525i)" or "576i (or 625i)".
•
Press [SHIFT]+[PROGRESSIVE] so "PRG" is displayed. Or select "480p (or 525p)" or
"576p (or 625p)" in "Video Output Mode" in Picture Menu.
•
If the unit is connected to the television through VIDEO OUT or S VIDEO OUT terminal, output
will be interlace, even if "PRG" is displayed.
•
Adjust the position of the FM or AM antenna.
•
Use an outdoor antenna.
•
Turn the television off or separate it from the unit.
•
Separate the antenna from other cables and cords.
•
Turn off the demo function.
•
If you set the clock, demo function will be turned off automatically.
•
Press [SHIFT]+[DIMMER] to brighten the display.
•
You inserted a disc the unit cannot play; insert one that can.
•
You inserted a blank disc.
•
You haven't inserted a disc; insert one.
•
You haven't inserted the disc correctly; insert it correctly.
•
Check and correct the speaker cord connections.
If this does not fix the problem, there is a power supply problem. Consult the dealer.
•
Disc is dirty. Wipe it clean.
•
Incorrect operation performed. Read the instructions and try again.
•
Trouble may have occurred. The number following "H" depends on the status of the unit.
Turn the unit off and back to ON. Alternatively, turn the unit off, disconnect the AC power
supply cord, and then reconnect it.
•
If the service numbers fail to clear, note the service number and contact a qualified service person.
•
You can only play DVD-Video if their region number is the same or includes the same region number
as the unit or if the DVD-Video is marked "ALL". Confirm the region number for the unit on the back of
the main unit.
•
Select "On" in "On-Screen Messages" in "Display" tab.
•
The operation is prohibited by the unit or disc.
•
You are trying to display incompatible contents.
•
Clean the heads.
•
If the erasure prevention tabs have been removed, cover the holes with adhesive tape.
Page
—
4
19
13
—
—
19
13
17
—
13
—
—
—
—
17
11, 17
4
—
26
—
—
6
6
25
7
—
—
31
5
7
—
—
—
—
19
—
—
31
21
RQT8092
29
29