Table of Contents
Advertisement
Available languages
Available languages
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket,
if the range is moved.
Failure to follow
these instructions can result
in death or serious burns to children and adults.
INSTALLATION REQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions
provided with any tools listed
here.
Tools needed
•
Tape measure
•
Flat-blade screwdriver
•
Phillips screwdriver
•
Level
•
Hand or electric drill
•
Hammer
•
Wrench or pliers
•
Pipe wrench
•
1846"combination
wrench
•
1¼,, d rive ratchet
•
3/8"nut driver
•
1/8"(3.2 mm) drill bit (for
wood floors)
•
Marker or pencil
•
Pipe-joint compound
resistant to LP gas
•
3/16"(4.8 mm) carbide-tipped
masonry drill bit (for
concrete/ceramic
floors)
•
Noncorrosive
leak-detection
solution
For LP/Natural Gas
Conversions
•
3/8"combination wrench
•
1/2"
combination wrench
•
%"
combination
wrench
•
7
mm
(9/32")
nut driver
•
Quadrex ®t or Phillips
screwdriver
•
Masking tape
Parts supplied
Check that all parts are included.
A
C
A. Anti-tip bracket
B. Plastic anchors (2)
C*
#10
X
1/211
screws
(2)
Anti-tip bracket must be securely mounted to subfloor.
Thickness of flooring may require longer screws to anchor
bracket to subfloor. Longer screws are available from your
local hardware store.
Parts needed
Check local codes and consult gas supplier. Check existing gas
supply and electrical supply. See "Electrical Requirements"
and
"Gas Supply Requirements"
sections.
1-@QUADREX
is a registered
trademark of NLW Holdings, Inc.
IMPORTANT: Observe all governing codes and ordinances.
Do
not obstruct flow of combustion
and ventilation air.
It is the installer's responsibility
to comply with installation
clearances specified on the model/serial rating plate. The
model/serial
rating plate is located on the oven frame behind
the top left side of the oven door.
The range should be located for convenient use in the
kitchen.
•
Recessed installations must provide complete enclosure of
the sides and rear of the range.
•
All openings in the wall or floor where range is to be installed
must be sealed.
•
Do not seal the range to the side cabinets.
•
Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
•
The floor anti-tip bracket must be installed. To install the anti-
tip bracket shipped with the range, see "Install Anti-Tip
Bracket" section.
Grounded electrical supply is required. See "Electrical
Requirements"
section.
Proper gas supply connection must be available. See "Gas
Supply Requirements" section.
Contact a qualified floor covering installer to check that the
floor covering can withstand at least 200°F (93°C).
Use an insulated pad or _¼"(0.64 cm) plywood under range if
installing range over carpeting.
IMPORTANT: To avoid damage to your cabinets, check with your
builder or cabinet supplier to make sure that the materials used
will not discolor, delaminate or sustain other damage. This oven
has been designed in accordance
with the requirements of UL
and CSA International and complies with the maximum allowable
wood cabinet temperatures
of 194°F (90°C).
Mobile Home - Additional
Installation
Requirements
The installation of this range must conform to the Manufactured
Home Construction
and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280). When such standard is not
applicable, use the Standard for Manufactured
Home
Installations, ANSI A225.1/NFPA 501A or with local codes.
In Canada, the installation of this range must conform with the
current standards CAN/CSA-A240-1atest
edition, or with local
codes.
Mobile
home installations
require:
•
When this range is installed in a mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the standards
listed above.
Advertisement
Table of Contents
