Electrical Requirements - Electrolux E30EW85EPS4 Installation Instructions Manual

Important Notes to the Installer
1. Read all instructions contained in these installation
instructions before installing the wall oven.
2. Remove all packing material from the oven
compartments before connecting the electrical supply
to the wall oven.
3. Observe all governing (;odes and ordinances.
4. Be sure to leave these instructions with the consumer.
5. THIS OVEN IS NOT APPROVED FOR STACKABLE OR
SDE-BY-SDE INSTALLATION.
Important Note to the Consumer
Keep these instructions with your Owners Guide for future
reference.
IMPORTANT SAFETY
NS
• Be sure your wall oven is installed and grounded
properly by a qualified installer or service
technician,
• This wall oven must be electrically grounded [n
accordance with local codes or, in their absence,
with the National Electrical Code ANSJ/NFPA
No.TO- latest edition in United Sates, or with CSA
Standard C22.1, Canadian Electrical Code, Part 1, in
Canada.
Stepping, leaning or sitting on the
door of this wall oven can result in serious injuries
and can also cause damage to the wall oven,
Never use your wall oven for warming or heating
the room, Prolonged use of the wall oven without
adequate ventilation can be dangerous.
The electrical power to the oven must
be shut off while line connections are being made,
Failure to do so could result in serious injury or
death.
1. Carpentry
Refer to figure I for the dimensions applicable to your
appliance, and tile space necessary to receive the oven.
Tile oven support surface may be solid plywood or
similar material, however the surface must be level from
side to side and from front to rear.
2. Electrical Requirements
This appliance must be supplied with the proper voltage
and frequency, and connected to an individual, properly
grounded branch circuit, protected by a circuit breaker or
fuse, having amperage as noted on the rating plate (the
rating plate is located on the oven frame).
Observe all governing codes and local ordinances
.
A 3-wire or 4-wire single phase 120/240 or 120/208
Volt, 60 Hz AC only electrical supply is required on
a separate circuit fused on both sides of the line
(time-delay fuse or circuit breaker is recommended).
DO NOT fuse neutral. Tile fuse size must not exceed
the circuit rating of the appliance specified on the
nameplate. Consideration must be given for a
combination builtqn oven and cooktop refer to unit
serial plate of each.
NOTE: Wire sizes and connections must conform with
the fuse size and rating of the appliance in accordance
with the American National Electrical Code ANS!/NFPA
No. 70qatest edition, or with Canadian CSA Standard
C22.1, Canadian Electrical Code, Part 1, and local codes
and ordinances.
An extension cord should not be used
with this appliance, Such use may result in a fire,
electrical shock, or other personaJ injury,
2. These appliances should be connected to the fused
disconnect (or circuit breaker) box through flexible
armored or nonmetallic sheathed cable. The flexible
armored cable extending from the appliance should
be connected directly to the junction box. The
junction box should be located as shown in figure 1
and with as much slack as possible remaining in the
cable between the box and the appliance, so it can
be moved if servicing is ever necessary.
3. A suitable strain relief must be provided to attach
tile flexible armored cable to the junction box.
Electrical Shock Hazard
• Electrical ground is required on this appliance.
• Do not connect to the electrical supply until
appliance is permanently grounded.
• Disconnect power to the junction box before
making the electrical connection,
• This appliance must be connected to a
grounded, metallic, permanent wiring system,
or a grounding connector should be connected
to the grounding terminal or wire lead on the
appliance,
• Do not use a gas supply line for grounding the
appliance.
Failure to do any of the above could result in a
fire, personal injury or eIectrica[ shock,
During cold temperature weather to
prevent damage to the oven control, wait at least three
(3) hours after receiving this built-in oven before
switching the power. This will prevent possible damage
to the builtqn oven control at power on.