Tools And Parts - Crosley CAWS966RQ1 Installation Instructions Manual

Selecting theproper location foryour w asher improves
performance andminimizes noise andpossible washer "walk."
Your washer canbeinstalled inabasement, laundry room, closet,
orrecessed area. See "Drain S ystem."
IMPORTANT: Donotinstall orstore the washer where i twill b e
exposed totheweather.
Proper installation isyourresponsibility.
Youwill need:
• Awater h eater settodeliver 120°F ( 49°C) water tothewasher.
• Agrounded electrical outlet l ocated w ithin 4 ft (1.2 m)of
where t hepower cord isattached totheback ofthewasher.
See "Electrical Requirements."
• Hotand coldwater faucets l ocated w ithin 3ft (90cm) o fthe
hotandcold water fillvalves, andwater pressure of5-100 psi
(34.5-690 kPa). Washers withtriple dispensers require
20-100 p si(138-690 kPa) forbest p erformance.
• Alevel floor w ithamaximum s lope of1"(2.5 cm) u nder entire
washer. Installing thewasher oncarpeting isnot
recommended.
• Asturdy f loor t osupport thewasher weight (washer, water
andload) of315Ibs(143 kgs).
Donotstore oroperate y our w asher intemperatures atorbelow
32°F (0°C). Some water canremain i nthewasher andcancause
damage inlowtemperatures. See "Washer Care" i ntheWasher
User I nstructions forwinterizing information.
Recessed area or closet installation
The dimensions shown are for the recommended spacing allowed
(A and B), except the closet door ventilation openings. The
dimensions shown for the closet door ventilation openings (C) are
the minimum required.
19,,T
(48.3cm)
3L
n
olo
1_ max.
(0cm) (68.6crn) (0cm) (2.Scrn) (64.8crn)
A B
(7.6crn)
"_48 in_ I
(155 ¢rn 2 }1 (7.6¢m)
<- 4" -- _-
(10.2 cm)
C
A. Front view
B. Side view
C. Closet door with vents
• Additional spacing should be considered for ease of
installation and servicing.
• Additional clearances may be required for wall, door and floor
moldings.
• Additional spacing of 1" (2.5 cm) on all sides of the washer is
recommended to reduce noise transfer.
If a closet door is installed, the minimum air openings in the
top and bottom of the door are required (C). Louvered doors
with air openings in the top and bottom are acceptable.
Companion appliance spacing should also be considered.
The washer can be installed using the standpipe drain system
(floor or wall), the laundry tub drain system, or the floor drain
system. Select the drain hose installation method you need. See
"Tools and Parts."
Standpipe drain system--wall or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe of
2" (5 cm). The minimum carry-away capacity can be no less than
17 gal. (64 L) per minute. A 11/4 '' (3.2 cm) diameter to 1" (2.5 cm)
diameter standpipe adapter kit is available. See "Tools and Parts."
The top of the standpipe must be at least 39" (99 cm) high and no
higher than 96" (244 cm) from the bottom of the washer.
39"
(9g crn)
Laundry tub drain system (view C)
The laundry tub needs a minimum 20 gal. (76 L) capacity. The top
of the laundry tub must be at least 39" (99 cm) above the floor and
no higher than 96" (244 cm) from the bottom of the washer.
Floor drain system (view D)
The floor drain system requires a siphon break that may be
purchased separately. See "Tools and Parts."
The siphon break must be a minimum of 28" (71 cm) from the
bottom of the washer. Additional hoses might be needed.