GE GTDS820ED0WS Installation Instructions Manual

Electric dryer

Advertisement

Installation
Instructions
Electric
Dryer
or Visit our Web site at: www.GEApplionces.com
(US)
J
BEFORE YOU BEGIN
Read these instructions completely and carefully.
, IMPORTANT
- save these instructions for local
inspector's use.
, IMPORTANT
- Observe all governing codes and
ordinances.
, Note to Installer - Be sure to leave these instructions with
the customer.
, Note to Customer - Keep these instructions with your Use
and Care Book for future reference.
, Before the old dryer is removed from service or discarded,
remove the dryer door.
, Service information and the wiring diagram are located in
the control console.
, Do not allow children on or in the appliance. Close
supervision of children is necessary when the appliance is
used near children.
, Install the dryer where the temperature is above 50°F for
satisfactory operation of the dryer control system.
AWAR
I G
, To reduce the risk of severe injury or death,
Fire Hazard
follow all installation instructions.
, Clothes dryer installation must be
performed by a qualified installer.
, Install the clothes dryer according to these instructions and in
accordance with local codes.
, This dryer must be exhausted to the outdoors.
, Use only rigid metal 4" diameter ductwork inside the dryer
cabinet and use only ULapproved transition ducting between
the dryer and the home duct.
, DO NOT install a clothes dryer with flexible plastic venting
materials. If flexible metal (semi-rigid or foil type)duct is
installed, it must be ULlisted and installed in accordance with
the instructions found in "Connecting Dryer to House Vent"
later in this manual. Flexible venting materials are known to
collapse, be easily crushed, and trap lint. These conditions will
obstruct clothes dryer airflow and increase the risk of fire.
, Do not install or store this appliance in any location where it
could be exposed to water and or weather.
,To reduce the risk of severe injury or death, follow all
installation instructions.
, Save these instructions. (Installers: Be sure to leave these
instructions with the customer).
234DI753P001Rev.
5 31-16697
_lk This is the safety alert symbol. This symbol alerts you to
potential hazards that can kill or hurt you and others.
All safety messageswill followthe safety alert symbol and the word
"DANGER" "WARNING"or "CAUTION". T hese words are defined as:
DANGER
Indicates a hazardous
situation which, if not
avoided, will result in
death or serious injury.
A WAR I G
Indicatesa hazardous
situation which, if not
avoided,could result in
death or seriousinjury.
CAUTIO
Indicates a hazardous
situation which, if not
avoided, could result in
minor or moderate injury.
AWA
I G
Fire Hazard
, No washer can completely remove oil.
, DO NOT dry anything that has ever had any
type of oil on it (including cooking oils).
, Items containing foam, rubber or plastic
must be dried on a clothesline or by using
an Air Dry cycle.
, Failure to follow this instructions can result
on death or fire
o
o
Q
o
Electrical
"
Shock Hazard
Plug into a grounded 3 prong outlet.
DO NOT remove ground prong.
DO NOT use an adapter.
DO NOT use an extension cord.
Failure to do so can result in death, fire, or
electrical shock.
Explosion
Hazard
, Keep flammable materials and vapors, such
as gasoline, away from dryer.
, Place dryer at least 18 inches (46 cm) above
the floor for a garage installation.
, Failure to do so can result in death,
explosion, or fire.
, DO NOTallow children on or in the appliance.
Close supervision of children is necessary
when the appliance is used near children.
NOTE:Installation and service of this dryer requires basic
mechanical and electrical skills.It is your responsibility to contact
a qualified installer to make the electrical connections.

Advertisement

Table of Contents
loading

Summary of Contents for GE GTDS820ED0WS

  • Page 1 Electric Installation Instructions Dryer or Visit our Web site at: www.GEApplionces.com (US) BEFORE YOU BEGIN _lk This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. Read these instructions completely and carefully. All safety messageswill followthe safety alert symbol and the word , IMPORTANT - save these instructions for local...
  • Page 2: Tools You Will Need

    Installation Instructions Minimum Clearance in Alcove or Closet Installation Minimum clearance to combustible surfaces and for air opening are: O in. clearance both sides, 3 in. front, 7 in. top and 3 in. rear. Consideration must be given to provide adequate clearance for installation and service TOOLS YOU MATERIALS YOU WILL NEED WiLL NEED...
  • Page 3 Installation Instructions [] ELECTRICAL CONNECTION INFORMATION CONNECTING DRYER USING 4-WIRE CONNECTION (MUST BE USED FOR MOBILE HOME INSTALLATION) NOTE: Since January 1,1996, the National Electric code requires that TO REDUCE THE RISK OF FIRE, the new constructions utilize a 4-wire connection to an electric dryer.
  • Page 4: Exhaust Information

    Installation Instructions EXHAUST INFORMATION CONNECTING DRYER USING 3-WIRE CONNECTION 'N cANADA AND 'N IFREQUIRED, BY LOCAL CODE, INSTALL EXTERNAL GROUND ( NOT PROVIDED) THE UNITED STATES, TOGROUNDED METAL, COLD WATER PIPE, OROTHER ESTABLISHED GROUND THE REQUIRED EXHAUST DUCT DIAMETER IS 4 in ll02mml. DO NOT USE DUCT LONGER THAN SPECIFIED IN THE EXHAUST DETERMINED BY AQUALIFIED...
  • Page 5: Exhaust Connection

    Installation Instructions @ EXHAUST CONNECTION For every extroo90°elbow, reduce the oollowooble v ent sgstem length bg 10 ft. Two 45° elbows will be treootedlike one 90° elbow. AWAR For the side exhooustinstoollootions, ooddone 90° elbow to the choort. Fire Hazard The totoolvent system length includes ooll t he strooightportions oondelbows of the sgstem (troonsitionduct included).
  • Page 6 Installation Instructions , For many applications, installing elbows at both the dryer STANDARD REAR EXHAUST and the wall is highly recommended (see illustrations (Vented ot floor level) below). Elbows allow the dryer to sit close to the wall without kinking and or crushing the transition duct, For straight line installation, connect...
  • Page 7: Alcove Or Closet Installation

    Installation Instructions [-_ LEVELING AND STABILIZING YOUR DRYER AWARNING Stand the dryer upright near the final location and adjust the 4 leveling legs, at the corners, to ensure that the dryer is level from side to side and front to rear. LEVEL Before the "Alcove or Closet SIDE-TO-SIDE...
  • Page 8 Installation Instructions TAB LOCATION E_ BATHROOM OR BEDROOM INSTALLATION • The drger lUST be vented to the outdoors. See EXHAUST INFORMATIONsection 3 & 4. • The installation must conform with local codes or, in the absence of local codes, with the NATIONAL ELECTRICAL CODE, ANSI/NFPA NO.
  • Page 9 Installation Instructions ADDING ELBOW AND DUCT FOR ADDING COVER PLATE TO REAR OF EXHAUST TO LEFT OR RIGHT SIDE OF CABINET (SIDES AND BOTTOM EXHAUST) CABINET . Preassemble 4" elbow with 4" duct. Wrap duct tape around joint. . Insert duct assembly, elbow first, through the side opening and connect the elbow to the dryer internal duct.
  • Page 10: Connecting Inlet Hoses

    Installation Instructions CONNECTING INLET HOSES CONNECTING INLET HOSES (cont.) (on some models) 7. Using pliers, tighten all the couplings with an additional two-thirds turn. To produce steam, the dryer must connect to the cold water supply. Since the washer must also connect to the NOTE: Do not overtighten.
  • Page 11 Installation Instructions ABOUT REVERSING THE DOOR Remove the bottom screw from eoch hinge (right side) ond portiolly insert them into the top left side hinge holes. SWING NOTE:All 4 front punel hinge screws will now be in the top hinge holes - 2 on the left ond 2 on the right. IMPORTANT NOTES: •...
  • Page 12 Installation Instructions Remove and swap the 2 cover caps and door handle _When the cover caps and door handle in place, mount from the outer door: the inner door back into the outer door with the screws removed in step 4. Make sure you mount the hinges on A.
  • Page 13: Reversing The Door Swing

    Loosen the bottom 2 right side hinge screws. Remove the door (]nd pl(]ce it on (] protected, fl(]t surf(]ce to (]void SOLID DOOR MODELS (]ng d(]m(]ge. Remove both the Blind Pl(]te (]nd the Strike WITH COVER CAPS: Pl(]te (]nd inst(]ll them in opposite positions.
  • Page 14 Installation Instructions Remove and swap the cover cap and door handle from _When the cover cap and door handle in place, mount the outer door: the inner door back into the outer door with the screws removed in step/4. Make sure you mount the hinges on the side opposite the handle.
  • Page 15 Installation Instructions REVERSING THE DOOR SWING Loosen the bottom 2 right side hinge screws. Remove the door and place it on (] protected fiat surface to (]void (]ng GLASS PANEL DOOR MODELS: damage. Remove both the Blind Plate and the Strike Plate and GHDS835ED0iVlC GTDS810EDOWS install them in opposite positions.
  • Page 16 Installation Instructions Remove and swap the 2 cover caps and door handle _When the cover caps and door handle in place, mount from the outer door: the inner door back into the outer door with the screws removed in step 4. Make sure you mount the hinges on the side opposite the handle.

Table of Contents