Page 2
Safetg Information BEFORE YOU BEGIN CONTENTS Read these instructions completely and carefully. Design Information Models Available ..............IM PORTANT- save these i nstructions Product Dimensions and Clearances ......3 local inspector's use. Tools and Parts Required ............ Parts Supplied ................I M PORTANT- Electrical Tools and Parts Required ........
Page 3
Design Information PRODUCT DIMENSIONS AND CLEARANCES NOTE: Appearance will vary by model. _21-1/2"_ 29-3/4" "1 19" ADVANCEPLANNING REQUIRED TOOLS PARTS (NOT SUPPLIED} • These ovens may be installed directly into a 30" wide oven cabinet. [] #2 Phillips screwdriver • Cutout dimensions are NOT the same for installation [] Hand held drill with or without an accessory storage drawer.
Page 4
National Electrical Code or prevailing local codes. Combined Speedcook and Warming Drawer Installation When installing the 8peedcook oven over a GE or Honogram electric warming drawer, a separate 120V, 60Hz, properly grounded receptacle must be installed. See instructions packed with the warming drawer.
Page 5
7/8" overlap on the bottom of the opening for all models. Allow 1-1/4" case trim overlap on the top for models PSB2200 and PSB2201 and 3//4" overlap on the top for models ZSC2200, ZSC2201 and ZSC2202. • Oven overlaps will conceal cut edges on all sides of the opening.
Page 6
Per Oven Per Oven Requirement Requirement 45-1/4" 2" Min. Min. _equirement • If Uou are replacing a GE/Honogram electric double oven with the combined installation NOTE: Additional clearances between the cutouts an Advantium 2/40V and a single oven, use the ma U be required.
Page 7
The amount of overlap on the sides for securing the oven. depends on the actual cutout width. Allow 1-1/4" case trim overlap on the top for models PSB2200 NOTE: Additional clearances between the cutouts and PSB2201 and 3/4"...
Page 8
Preparation WITHan AccessoryStorage Drawer NOTE:MODELZSC2202CANNOTBE INSTALLED WITH AN ACCESSORY S TORAGE DRAWER. S EEINSTALLATION PREPARATION WITHOUTAN ACCESSORY S TORAGE DRAWERFORTHISHODEL. PREPARE THE OPENING (CONT.) PREPARE THE OPENING (CONT.) Installation over a GE/Nonogram Oven: Installation over a GE/Monogram Oven Warming Drawer: Construct Solid 30"...
Page 9
Installation Instructions REMOVE THE PACKAGING AND PARTS ° Remove all packing material and tape. • Locate parts package containing mounting screws. • Remove the oven from the carton. Do not lift unit bg handle or conduit. Two people are required to lift this oven.
Page 10
Installation Instructions ROUTE CONDUIT THROUGH ROUTE CONDUIT THROUGH CUTOUT CUTOUT (CONT.) CAUTIO N: When connecting to a 3-conductor branch Two people are required to lift circuit: the oven into the opening. Grasp the bottom • Connect oven red lead to branch circuit red lead. front and rear.
Page 11
Installation Instructions INSTALL MOUNTING SCREWS INSTALL BOTTOM TRIM NOTE: If installing the Advantium 2/40 Oven with an accessoru storage drawer, the bottom trim is not required. Proceed to Step/4. • Align bottom trim tabs to slots in the bottom of the oven.
Page 12
Assembly Instructions Advantium ®240V Built-ln Accessory Storage Drawer J×2200, J×2201, Z×2201 BEFORE YOU BEGIN MODELS AVAILABLE Profile Models: Read these instructions completely and carefully. Read JX2200BB-Block the Installation Instructions for the Advantium 240V oven JX2201SS-Stoinless Steel completely and carefully for cutout dimensions and step-by-step instructions.
Page 13
ASSEMBLYTO ADVANTIUM 240V BUILT-IN SPEEDCOOK OVEN ASSEMBLING THE OVEN TO DRAWER REMOVE PACKAGING AND PARTS (CONT.) • Remove the drawer from the carton. Remove the front two bottom screws on each • Remove all packing material and tape. side of the oven and the top center screw on •...
Page 16
NOTE: while performing installations described in this book, safety glasses or goggles should be worn GE Consumer & Industrial NOTE: Product improvement is a continuing endeqvor at Appliances General Electric Therefore, materials, appearance and General Electric Company specifications are subject to change without notice Louisville, KY/40225 ge.com...