THESE INSTALLATION INSTRUCTIONS ARE INTENDED FOR USE BY QUALIFIED INSTALLERS, Xn add(tion to these instructionsthe dishwasher shall be installed: (n the Un(ted States, (n accordance w(th the Nat(ona) Electr(c Code/State Municipal codes and/or local codes, • In Canada, in accordance with the Canadian Electric...
Accessory Parts Supplied Accessory Parts for your model dishwasher will come in one or more plastic bags, Check to make sure that the parts supplied for your model are all there, See Figure 3. If any parts are missing contact your dealer immediately.
THBEIN AW INSTRUCTIONS INTENDEDFORU_ BY QU_EDINSTALLE_ Choosing the Location Select a locationas close to the sink as possible forready accessto water and drain (49ram) lines. Most of the installation work is done before the dishwasher is moved into place. Figure 4 built-in dishwasher must...
Figure 9. Hot water line Electrical supply cable Figure 7 1. In order to reduce running time, Bosch recommends 140 ° F water inlet temperature. Your dishwasher will perform equally as well at 120 ° F water temperature,...
Electricam SuppNy customer has the responsibility ensure that the dishwasher installation in compliance with all national and local electrical codes ordinances. dishwasher shall be installed by a qualified Figure 8 electrician properly grounded. electrical supply for which the dishwasher is designed is 120\/, 60 Hz, AC, connected to a dishwasher-dedicated electrical...
A, Mounting bracket Placing the Dishwasher for mounting to under profile strips on the sides of the countertop dishwasher allow the dishwasher to fit into a cabinet opening with a width of 23-5/8" (600 mm) to 244[/8" (613 mm). Before sliding dishwasher into...
THESE NSTALLA ON IN U ONS _N_NDEDFORUSEBY I QU_EDINSTALLE_ Be sure to follow your national and local codes at all times. Drain Hose Figure Before beginning, turn off the water supply! The access hole for the drain hose should be 1.25" (32 ram) diameter, Air Gap_ Use the hose damps and rubber connection...
TNESE NST LA ON INSTRU ONS INTENDED FORUSE QUALI_EDINSTALLE_ Connecting the Hot Water $uppIv Line Ifusing a solderjoint insteadof acom _ pression fitting, be sure to make aft Figure solder connections before connecting the water line to the dishwasher. Make sure there are no sharp bends or kinks in the water line which might...
INSTRU_ONS ELECTRICAL SHOCK HAZARD IN_NDED _RUSE • DISCONNECT ELECTRICAL POWER QU_FIED INST_JUE_ AT THE CIRCUIT BREAKER BOX OR FUSE BOX BEFORE INSTALLING DISHWASHER. Connecting ElectricaN Supply • ELECTRICALLY GROUND DISH- Be sure to follow all local natio- WASHER. nal electrical codes ordinances, •...
Accessory Panel Installation SHU Modets If you have an SHU model and have ordered an accessory panel kit it must be installed prior to sliding the dishwasher into place. Dimensions of panel size that may be used is shown in Figure Panel Installation, SHV Models If you have an SHV model, a fully integrated...
Page 14
SEE FOLDED PANEL INSTALLATION TEMPLATE SHEET FOR STEP BY STEP INSTRUC_ONS ON HOW TO INSTALL YOUR DISHWASHER PANEL(S), Figure 19 IMPORTANT Do NOT DrillComp(etely through your custom door panel. EXTENSION "A" MAX -MIFf "C" MODEL "B" MAX -MIN STANDARD LONG 11/16=5/16"...
Door Tension Adjustment (only in $HI and SHV models) After installation of the dishwasher, open and close the door several times to make sure that it does so with ease, If the door closes too quickly or if the door falls open, the spring tension needs to be adjusted.
$HY66 _ $H×56 Series Base and Toe Panel Installation Steps Installation Parts SHY66 & SHX56 Base Part Base Part Screws SHY66 & SHX56 Toe Panel SHU Toe Panel Screws SHY66 & SHX56 Installation (Refer to "Materials Supplied" section) Junction Box Cover and Screw Remember to carefully check, the "Materials Figure Supplied"...
R_u_ar Toe Pane_ Installation (for models other than $HY66 & $HX56) • Obtain Toe Panel Screws from the Dishwasher Installation Kit bag (see Figure Insert screws through the Toe Panel. With a Torx screwdriver, fasten screws Figure28 and toe panel into dishwasher base.
If problem persists, take the following steps (in the order listed below) until the problem is corrected to your satisfaction. Contact your installer or the Bosch Authorized Service Contractor in your area. E-mail us from the Customer Service section of our web site, www.boschappliances.com,...