Led Indicators - Samson MDR16 Owner's Manual

MASTER OUTPUT SECTION
48
MIX/2TK
The MIX/2TK switch selects the signal source that you are monitoring in the CONTROL ROOM and HEADPHONE
outputs. When the switch is in the up position, the signal source is from the LEFT/ RIGHT MIX bus. When the MIX/
2TK switch is in the down position, the signal source is from the 2 TRACK input.
49
SOLO LEVEL
You can adjust the overall volume of the SOLO bus
by using the SOLO LEVEL control knob. The SOLO
LEVEL is active when any SOLO button is engaged.
50
C/ROOM + PHONES
The C/ROOM + PHONES control is used to set the
level sent to the control room outputs, and also to
the headphone jack.
51
1/2 FADERS
The 1/2 Bus faders are the over-all volume con-
trols for the 1/2 MIX bus. If the 1/2 TO MIX switch is
engaged, the 1/2 MIX faders will affect the signal
that is being sent out the CONTROL ROOM outputs,
and signal that is being sent out the MIX OUTPUT
jacks. If the 1/2 TO MIX switch is not engaged, the
1/2 MIX faders will affect the signal that is being sent
out the 1/2 OUTPUT jacks.
52
3/4 FADERS
The 3/4 Bus faders are the over-all volume controls
for the 3/4 MIX bus. If the 3/4 TO MIX switch is engaged, the 3/4 MIX faders will affect the signal that is being sent
out the CONTROL ROOM outputs, and signal that is being sent out the MIX OUTPUT jacks. If the 3/4 TO MIX switch
is not engaged, the 3/4 MIX faders will affect the signal that is being sent out the3/4 OUTPUT jacks.
53
L MIX R FADER
The L&R MIX fader IS the over-all volume control for the main MIX bus. The L&R MIX fader affects both the signal
which is output to the CONTROL ROOM speakers and the line level signal which is output from the LEFT and RIGHT
MIX OUTPUT jacks.

LED INDICATORS

54
POWER LED
The Power LED lights up to indicate that the main POWER switch, (located on the rear
panel), is on and the mixer is powered-up.
55
+48V - Phantom Power LED
The +48V LED illuminates indicating that the 48 volt phantom power is applied to the
microphone pre-amps enabling use with condenser microphones. The +48V LED will light
up when the Phantom Power switch (located on the rear panel) is switched to the ON posi-
tion.
56
SOLO LED
The SOLO LED lights up to indicate that the SOLO bus is now being heard in the
Headphones and Control Room outputs.
57
PFL LED
The PFL LED lights up to indicate that the SOLO is in PFL mode.
58
Output Level Meter
The OUTPUT LEVEL METER allows you to monitor the level of the signal which is being sent
to the L&R MIX OUTPUT jacks.
NOTE: To avoid distortion, adjust the L/R MIX faders LEVEL control so that the 0 indicator LED lights occasionally.
Controls and Functions
����
��� �� ��� ��� �� ���
� ������� � � �������
��
� � � � � �
� � � � � � �
� � � � � �
� � � � � �
�
�
��
��
��
��
��
��
� ������� � � �������
15
���� ��������
����������� ��������
� � ���
������
��
�� ��
����
�����
� � � �
�
��
� � � � � �
� � � �
� � � �
� �
� ��
�
� �
��
�� ��
� ��
������
�������
�� ��
�� ��
�� ��
�� ��
��
� ������ � ���
��
�����
���
��
����
����
���
��
��
��
�
��
��
��
���
���
���
���
��
�
��
�
�
�
��
��
��
��
��
��
�
��
��
��
���