Related Manuals for Robot Coupe R302V
Summary of Contents for Robot Coupe R302V
- Page 1 OPERATION MANUAL MODEL R302V robot coupe U.S.A., Inc. P.O. Box 16625, Jackson, MS 39236-6625 280 South Perkins St., Ridgeland, MS 39157 email: robocoup@misnet.com website: www.robotcoupeusa.com 1-800-824-1646...
- Page 2 R302V Operation Manual...
- Page 3 GUIDE repaired at one of the Robot Coupe Authorized Ser- vice Agencies, a list is provided in the back of this TROUBLE SHOOTING AIDS manual. Contact one of these service agencies for all of your service, parts and accessory requirements.
- Page 4 R302V Operation Manual II. ASSEMBLY/DISASSEMBLY INSTRUCTIONS Your Robot Coupe should be placed on a sturdy work surface at a comfortable working height and have a standard 115 volt power outlet available. Always keep the machine unplugged during assembly and disas- sembly.
- Page 5 R302V Operation Manual B. CONTINUOUS FEED ATTACHMENT ASSEMBLY INSTRUCTIONS If you are preparing to use the dicing or the French fry combinations French Fry combinations; First follow steps 1, 2, and 3 above. Then, fit the molded plastic piece of Dicing;...
- Page 6 R302V Operation Manual III. OPERATING INSTRUCTIONS The continuous feed lead serves several functions. Primarily, the lead protects the operator from the cut- ting plate. When the lead is fully locked in place, the NOTE: This machine is equipped with manual reset plate is covered and the unit will be ready for opera- thermal overload protection.
- Page 7 Follow the directions shown to sharpen the blade, or have the blades sharpend professionaly if you prefer. 1. Put on your cut-resistant gloves 2. Use the Robot Coupe stone or any good sharpening stone. 3. Hold or clamp the blade flat on the edge or corner of a sturdy table.
- Page 8 The Robot Coupe Food Processor will slice, grate, shred and julliene. These processes will be performed in a matter of seconds. Because of the speed of the process, it is necessary that the operator perform pre- liminary steps before turning the machine on.
- Page 9 Plate Utilization DO NOT put anything other than food The Robot Coupe food processor will perform a vari- products in the feed chute. ety of functions: slicing, grating, French fry, and julienne. There are a total of 25 different plates avail-...
- Page 10 R302V Operation Manual Plate Usage GRATING PLATES SLICING PLATES There are eight grating plates available for use with the Robot Coupe: R291 1/32" or 1mm Slicing Plate The thinnest slicing plate is the R291. It is used for Part Number Metric Inches (Approx.)
- Page 11 R302V Operation Manual R281 1/8" or 3mm Medium Coarse Grating R288 5/32 x 5/32" or 4mm x 4mm Julienne Plate This new size grating plate is good for an extra fine This is the most popular of the julienne plates. Car- coleslaw or anything you prefer grated a bit coarser rots, yellow squash, and zucchini work best.
-
Page 12: Cleaning/Preventive Maintenance
Correct cleaning procedures are required to assure that damage is not inflicted in the cleaning process. While the standard Robot Coupe comes with two spe- The motor base assembly contains the motor and cific plates (R209 and R211 at time of printing), many electrical components. -
Page 13: Troubleshooting Aids
(small pieces of (3) CARE: While your Robot Coupe is a ruggedly con- plastic would be present). structed machine, overall handling should be accom- 2. - Page 14 SERVICE AGENCY LIST 1. Blade is dull on plate and must be changed. NOTE: Cucumber condition before process Your Robot Coupe has a one year limited warranty ing should be considered. against defects in parts and workmanship. Should the unit require service, check with your distributor H.
- Page 16 PRICES AND OTHER INFORMATION SUBJECT TO CHANGE WITHOUT NOTICE Model Price list for USA only R302V Part # Description 39084 (F) Magnetic Switch Assy, R302V CL302 Base CL316 Screw Cover CL318 Motor Base Screw CL319 Cont. Feed Attach. CL320 Discharge Plate Assy.
- Page 18 KEEP ALL ORIGINAL CONTAINERS AND PACKING MATERIALS FOR CARRIER INSPECTION. Robot Coupe U.S.A., Inc., Robot Coupe S.A. or any of their affiliates, distributors, officers, directors, agents, employees, or insurers will not be obligated for consequential or other damages, losses, or expenses in connection with or by reason of the use of or inability to use the machine for any purpose.