Grizzly G1060 Instruction Manual
  1. Manuals
  2. Brands
  3. Grizzly Manuals
  4. Saw
  5. G1060
  6. Instruction manual

Grizzly G1060 Instruction Manual

22" scroll saw
Hide thumbs
Table of Contents

Advertisement

Quick Links

22'' SCROLL SAW
MODEL G1060

INSTRUCTION MANUAL

COPYRIGHT © 1992 BY GRIZZLY IMPORTS, INC. REG.# TX 3 300 229
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY IMPORTS, INC.
REVISED JULY 1997 PRINTED IN TAIWAN

Advertisement

Table of Contents
loading

Related Manuals for Grizzly G1060

Summary of Contents for Grizzly G1060

  • Page 1: Instruction Manual

    22'' SCROLL SAW MODEL G1060 INSTRUCTION MANUAL COPYRIGHT © 1992 BY GRIZZLY IMPORTS, INC. REG.# TX 3 300 229 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY IMPORTS, INC.

  • Page 3: Table Of Contents

    STRAIGHT CUTS ...12 CURVED CUTS...13 BEVEL CUTS ...13 INSIDE CUTS ...14 MAINTENANCE ...15 GENERAL ...15 WORKING TABLE...15 LUBRICATION ...15 CLOSURE...16 MACHINE DATA ...17 PARTS BREAKDOWN AND PARTS LISTS ...18-19 WARRANTY AND RETURNS...20 G1060 22'' Scroll Saw Table Of Contents PAGE...

  • Page 4: Safety

    Always repair or replace extension cords if they become damaged. Minimum gage for extension cord: 16 A.W.G. 50ft 16 A.W.G. 100ft 14 A.W.G. 200ft 12 A.W.G. 300ft G1060 22'' Scroll Saw...

  • Page 5: Additional Safety Instructions For Scroll Saws

    Adjust Hold-down Foot so it barely touches your workpiece. G1060 22'' Scroll Saw 16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off posi- tion before plugging in.

  • Page 6: Circuit Requirements

    SECTION 2: CIRCUIT REQUIREMENTS 110V Operation Your G1060 22'' Scroll Saw is prewired for 110 volt, single phase operation. The draws approximately 2.2 amps. We strongly rec- ommend fusing your Scroll Saw at 15 amps. Fusing higher will not adequately protect the motor.

  • Page 7: General Information

    The Model G1060 is capable of a wide variety of operations. The 22'' throat capacity enables you to maneuver large workpieces for a variety of intricate operations.

  • Page 8: Unpacking

    Unpacking The Model G1060 22'' Scroll Saw is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you’ve signed for delivery, please call Customer Service immediately for advice. Save the containers and all packing materials for possible inspection by the carrier or its agent.

  • Page 9: Clean Up

    Clean up The working table for the G1060 is coated with a waxy oil that protects them from corrosion during shipment. Remove the protective coating with mineral spirits and paper towels. Do not use gasoline or other petroleum based solvents because of their extremely low flash points.

  • Page 10: Assembly

    SECTION 4: ASSEMBLY Safety Shield The only real assembly required for your scroll saw is to attach the safety shield to the support post. Slide the mounting clip over the threaded end of the mounting rod and secure with wing nut provided.

  • Page 11: Adjustments

    Remove Table Insert and flip open Chuck Guards. Figure 3. Figure 3. G1060 22'' Scroll Saw 3. Mount Blade in Chucks. This can be done with the help of the Chuck Holder, located on the right edge of the table. Figure 4.

  • Page 12: Blade Tension

    Figure 5. -10- Table Tilt Your Scroll Saw can handle any sort of bevel cut between 0 and 30˚. Before you try this, however, make sure the blade is perpendicular to the table. Recalibration of this setting is easy.

  • Page 13: Safety Shield

    Now that the table is perpendicular to the blade, any angle you set between 0 and 30˚ will be accurate. To do this: 1. Facing the Saw, turn the Table Insert 90˚ to the right as shown in Figure 7. Figure 7.

  • Page 14: Operations

    Make sure the blade is cutting to the waste side of the line. Figure 9. Figure 9. G1060 22'' Scroll Saw...

  • Page 15: Curved Cuts

    Figure 10. Figure 10. G1060 22'' Scroll Saw Bevel Cuts Scribe your workpiece as described in the previous two sections. Adjust table to desired angle.

  • Page 16: Inside Cuts

    Inside Cuts Inside cuts such as circles or the insides of closed letters can be easily cut with your Scroll Saw by threading the blade through the workpiece’s closed loop from the bottom and remounting the blade in the chucks. This procedure is described below.

  • Page 17: Maintenance

    SECTION 7: MAINTENANCE General Regular periodic maintenance on your Model G1060 Scroll Saw will ensure its optimum perfor- mance. Make a habit of inspecting your scroll saw each time you use it. Check for the following con- ditions and repair or replace when necessary.

  • Page 18: Closure

    As with all power tools, there is danger associat- ed with the Model G1060 22'' Scroll Saw. Use the tool with respect and caution to lessen the possi- bility of mechanical damage or operator injury. If...

  • Page 19: Machine Data

    GRIZZLY MODEL G1060 22 Design Type ... Bench Model Capacities: Maximum Cutting Width...22" Maximum Cutting Height...1 Table Tilt ...0-30 Overall Dimensions: Base ...20 Table ...17 Height...15" Width ...29" Depth ...11" Blade to Frame ...21 Container Dimensions ...10" x 19 Shipping Weight ...62 lbs.

  • Page 20: Parts Breakdown And Parts Lists

    -18- G1060 22'' Scroll Saw...
  • Page 21 P1060036 ADJUSTMENT KNOB 36A PN02M HEX NUT M10-1.5 P1060037 SUPPORT ARM P1060038 AIR HOSE P1060039 HOSE CLAMP *replacement chucks supplied with setscrews. G1060 22'' Scroll Saw PART # DESCRIPTION P1060040 ADJUSTMENT KNOB P1060041 STAR WASHER 5MM P1060042 POINTER PS09M CAP SCREW M5-0.8 X 10MM...

  • Page 22: Warranty And Returns

    WARRANTY AND RETURNS Grizzly Imports, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, neg- ligence, accidents, repairs or alterations or lack of maintenance.

Table of Contents