Advertisement
Please note that some of the contact details on
this PDF document may not be current.
Please use the following details if you need to
Email: customer.services@gdcgroup.co.uk
The Help Centre section of this website also features a wide range
of information which may be of use to you and is available 24
hours a day. It includes:
• Operating and installation instructions downloads
• Request a repair
• Where to buy our products
• Literature downloads
• Heating requirement calculator
A division of GDC Group Ltd
Millbrook House Grange Drive Hedge End Southampton SO30 2DF
www.credaheating.co.uk
Contact Details
contact us:
Telephone: 0844 879 3588
www.credaheating.co.uk/help‐centre
Registered No: 1313016 England
VAT GB 287 1315 50004
EEE Producer Registration Number –
WEE/GE0057TS
Paper from sustainable sources
Advertisement
Table of Contents
Related Manuals for Creda 70305S
Summary of Contents for Creda 70305S
- Page 1 Contact Details Please note that some of the contact details on this PDF document may not be current. Please use the following details if you need to contact us: Telephone: 0844 879 3588 Email: customer.services@gdcgroup.co.uk The Help Centre section of this website also features a wide range of information which may be of use to you and is available 24 hours a day. It includes: • Operating and installation instructions downloads • Request a repair • Where to buy our products • Literature downloads • Heating requirement calculator www.credaheating.co.uk/help‐centre A division of GDC Group Ltd Registered No: 1313016 England VAT GB 287 1315 50004 Millbrook House Grange Drive Hedge End Southampton SO30 2DF EEE Producer Registration Number –...
- Page 2 SFHAW Sensair Fan Heater Assembly Instruction Model Nos: 70305S 70315S Cat. Nos: SFH18AW SFH24AW This product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2 and EN60555-3. These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC ©...
- Page 3 IMPORTANT NOTES: It is important to read these instructions carefully and also note the information given on the heater itself. As these particular instructions refer to the assembly and installation of a new heater, they should be retained by the installer; not left behind for the user as this would invite the dismantling and servicing by unqualified persons.
- Page 4 PLEASE DON’T TAKE CHANCES Site conditions may vary considerably and Creda cannot recommend the correct wall fixings to be used. It is the responsibility of the installer to ensure that adequate permanent fixing has been achieved. Purely for guidance the suggested fixings are made for certain wall materials but this list is not comprehensive or authoritative.
- Page 5 The panel can now be lifted clear and set to one side. Remove the packing pieces from the slots of the inner front (one on the 70305S and two on the 70315S) see Fig.
- Page 6 Connect the EARTH lead from both supplies to the terminal marked with the symbol. Storage and Fan/Boost Circuit Charge Rated CONNECTING Period Charge 70305S 7 hours 18 kWh THE SUPPLIES 70315S 7 hours 24 kWh...
- Page 7 Ensure that any slack is pulled back through each clamp and tighten the clamping screws. Make sure clamp is tightening on outer sheath of cable and not on individual conductors. Secure cables to base of heater using ties provided in fixing kit.
- Page 8 WALL FIXINGS - VERY IMPORTANT THE FOLLOWING MUST BE APPLIED You must fit a WHEN FIXING THE HEATER TO THE retaining screw at WALL BRACKET each end of the heater. If no skirting board is present secure the heater through the wall bracket slots closest to the wall. If 100mm (4”) skirting is present secure the heater through the outer slots.
- Page 9 The lower front panel can now be fitted by locating the tabs (one on the 70305S and two on the 70315S) into the corresponding slots in the bottom face of the front panel. The two black screws should now be replaced at each side of the heater.